Page 86 / 111
Scroll up to view Page 81 - 85
Huawei Technologies Proprietary
76
Figure 4-27
Diagnostics Window
Select the Virtual Circuit and click the
Submit
button. A
message will appear, informing you whether the loop test succeeded
or failed.
The diagnostics utility will run a series of test to check whether
the device's connections are up and working. This takes only a few
seconds. The program reports whether the test passed or failed. A
test may be skipped if the program determines that no suitable
interface is configured on which to run the test.
Page 87 / 111
Huawei Technologies Proprietary
77
The Ping utility is essentially a tool that is used to see if a
computer is operating and also to see if network connections are
intact. You can enter the host name or IP address of the device you
want to check, and then click the
Ping
button. The result will be
shown below.
4.20
Traffic Statistics
Click the
Traffic Statistics
of
Status
in the Wizard Column to
view the log of device.
Figure 4-28
Traffic Statistics
The device keeps statistic of the data traffic that it handles. You
are able to read the amount of Receive and Transmit packets that
pass through the device on both the WAN (Wide Area Network) ports
and the LAN (Local Area Network) ports. Click the
Refresh
button to
update the counters and the
Reset
button to clear the counters. The
traffic counter will reset when the device is rebooted.
Page 88 / 111
Huawei Technologies Proprietary
78
5
Service Configuration
This section describes the configuration for six modes of
SmartAX MT882 ADSL router device for ADSL online service. The
contents include:
z
Preparation for service configuration
z
PPPoE
z
PPPoA
z
RFC 2684 Bridged (Pure Bridge)
z
RFC 2684 Bridged (Static IP)
z
RFC 2684 Bridged (DHCP)
z
RFC 2684 Routed (IPoA)
5.1
Preparation for Service Configuration
Collect the following data firstly to perform the configuration:
Page 89 / 111
Huawei Technologies Proprietary
79
Virtual dialup
mode
DSL mode
Protocol
types
PPPoE
PPPoA
RFC
2648
Bridged
(Pure
Bridge)
RFC
2684
Bridged
(Static
IP)
RFC
2684
Bridged
(DHCP)
RFC
2684
Routed
(IPoA)
Connec
tion
Type
Connec
tion
Type
Connec
tion
Type
Connecti
on Type
Connec
tion
Type
Conne
ction
Type
PPPoE
user
name
PPPoA
user
name
VPI/
VCI
VPI/
VCI
VPI/
VCI
VPI/
VCI
PPPoE
passwo
rd
PPPoA
passwo
rd
None
WAN IP
None
WAN
IP
VPI/VCI
VPI/VCI
None
Subnet
mask
None
Subnet
mask
Security
Protocol
Security
Protocol
None
Default
gateway
None
Default
gatewa
y
Preparing
information
None
None
None
DNS
DNS
DNS
Page 90 / 111
Huawei Technologies Proprietary
80
5.2
PPPoE Configuration
Configurations on MT882
Location
Parameters
Comments
PVC
Select any one from the eight
PVCs.
VPI/VCI
The value shall be provided by
your ISP.
Wan Type
Select “PPP”.
Connection
type
Select “PPPoE”.
User name
and Password
The values shall be provided by
your ISP.
Default Route
Select “Enable”.
ATM Setting
DNS
Select “Enable”.
DNS
It is recommended to have DNS Relay function
enabled.
DHCP Mode
It is recommended to have DHCP Server function
enabled.
Configurations on the user PC
IP Address
and Network
Mask
It is recommended to set the mode as obtaining
an IP address automatically.
DNS
It is recommended to set the mode as obtaining a
DNS server’s IP address automatically.
19216811.live