Chapter 4 Internet and Wireless Setup Wizard

P-660HN-FxZ Series User’s Guide

56

Figure 16

Internet Access Wizard Setup: ISP Parameters

The following table describes the fields in this screen.

Table 8

Internet Access Wizard Setup: ISP Parameters

LABEL

DESCRIPTION

Mode

Select

Routing

(default) from the drop-down list box if your ISP give you one IP

address only and you want multiple computers to share an Internet account. Select

Bridge

when your ISP provides you more than one IP address and you want the

connected computers to get individual IP address from ISP’s DHCP server directly. If

you select

Bridge

, you cannot use Firewall, DHCP server and NAT on the ZyXEL

Device.

Encapsulation

Select the encapsulation type your ISP uses from the

Encapsulation

drop-down list

box. Choices vary depending on what you select in the

Mode

field.

If you select

Bridge

in the

Mode

field, select either

PPPoA

or

RFC 1483

.

If you select

Routing

in the

Mode

field, select

PPPoA

,

RFC 1483

,

ENET ENCAP

or

PPPoE

.

Multiplexing

Select the multiplexing method used by your ISP from the

Multiplex

drop-down list

box either VC-based or LLC-based.

Virtual Circuit

ID

VPI (Virtual Path Identifier) and VCI (Virtual Channel Identifier) define a virtual circuit.

Refer to the appendix

for more information.

VPI

Enter the VPI assigned to you. This field may already be configured.

VCI

Enter the VCI assigned to you. This field may already be configured.

Back

Click this to return to the previous screen without saving.

Next

Click this to continue to the next wizard screen. The next wizard screen you see

depends on what protocol you chose above.

Exit

Click this to close the wizard screen without saving.

Chapter 4 Internet and Wireless Setup Wizard

P-660HN-FxZ Series User’s Guide

57

2

The next wizard screen varies depending on what mode and encapsulation type you use.

All screens shown are with routing mode. Configure the fields and click

Next

to

continue. See

Section 4.3 on page 60

for wireless connection wizard setup

Figure 17

Internet Connection with PPPoE

The following table describes the fields in this screen.

Figure 18

Internet Connection with RFC 1483

Table 9

Internet Connection with PPPoE

LABEL

DESCRIPTION

User Name

Enter the user name exactly as your ISP assigned. If assigned a name in the form

user@domain where domain identifies a service name, then enter both components

exactly as given.

Password

Enter the password associated with the user name above.

Service Name

Type the name of your PPPoE service here.

Back

Click this to return to the previous screen without saving.

Apply

Click this to save your changes.

Exit

Click this to close the wizard screen without saving.

Chapter 4 Internet and Wireless Setup Wizard

P-660HN-FxZ Series User’s Guide

58

The following table describes the fields in this screen.

Figure 19

Internet Connection with ENET ENCAP

The following table describes the fields in this screen.

Table 10

Internet Connection with RFC 1483

LABEL

DESCRIPTION

IP Address

This field is available if you select

Routing

in the

Mode

field.

Type your ISP assigned IP address in this field.

Back

Click this to return to the previous screen without saving.

Next

Click this to continue to the next wizard screen.

Exit

Click this to close the wizard screen without saving.

Table 11

Internet Connection with ENET ENCAP

LABEL

DESCRIPTION

Obtain an IP

Address

Automatically

A static IP address is a fixed IP that your ISP gives you. A dynamic IP address is not

fixed; the ISP assigns you a different one each time you connect to the Internet.

Select

Obtain an IP Address Automatically

if you have a dynamic IP address.

Static IP

Address

Select

Static IP Address

if your ISP gave you an IP address to use.

IP Address

Enter your ISP assigned IP address.

Subnet Mask

Enter a subnet mask in dotted decimal notation.

Refer to the appendix

to calculate a subnet mask If you are implementing subnetting.

Gateway IP

address

You must specify a gateway IP address (supplied by your ISP) when you use

ENET

ENCAP

in the

Encapsulation

field in the previous screen.

First DNS

Server

Enter the IP addresses of the DNS servers. The DNS servers are passed to the DHCP

clients along with the IP address and the subnet mask.

Second DNS

Server

As above.

Back

Click this to return to the previous screen without saving.

Chapter 4 Internet and Wireless Setup Wizard

P-660HN-FxZ Series User’s Guide

59

Figure 20

Internet Connection with PPPoA

The following table describes the fields in this screen.

•

If the user name and/or password you entered for PPPoE or PPPoA connection are not

correct, the screen displays as shown next. Click

Back to Username and Password setup

to go back to the screen where you can modify them.

Apply

Click this to save your changes.

Exit

Click this to close the wizard screen without saving.

Table 12

Internet Connection with PPPoA

LABEL

DESCRIPTION

User Name

Enter the login name that your ISP gives you.

Password

Enter the password associated with the user name above.

Back

Click this to return to the previous screen without saving.

Apply

Click this to save your changes.

Exit

Click this to close the wizard screen without saving.

Table 11

Internet Connection with ENET ENCAP (continued)

LABEL

DESCRIPTION

Chapter 4 Internet and Wireless Setup Wizard

P-660HN-FxZ Series User’s Guide

60

Figure 21

Connection Test Failed-1

•

If the following screen displays, check if your account is activated or click

Restart the

Internet/Wireless Setup Wizard

to verify your Internet access settings.

Figure 22

Connection Test Failed-2.

4.3

Wireless Connection Wizard Setup

After you configure the Internet access information, use the following screens to set up your

wireless LAN.

1

Select

Yes

and click

Next

to configure wireless settings. Otherwise, select

No

and skip

to Step

6

.