1. Home
    2. /
  2. Manuals
    3. /
  3. Zyxel
    4. /
  4. P-660HN-F1Z
    5. /
  5. 8
Page 36 / 421 Scroll up to view Page 31 - 35
Chapter 1 Introducing the ZyXEL Device
P-660HN-FxZ Series User’s Guide
36
Refer to the Quick Start Guide for information on hardware connections.
1.6
The RESET Button
If you forget your password or cannot access the web configurator, you will need to use the
RESET
button at the back of the device to reload the factory-default configuration file. This
means that you will lose all configurations that you had previously and the password will be
reset to “1234”. You can also use the
1.6.1
Using the Reset Button
1
Make sure the
POWER
LED is on (not blinking).
2
To set the device back to the factory default settings, press the
RESET
button for ten
seconds or until the
POWER
LED begins to blink and then release it. When the
POWER
LED begins to blink, the defaults have been restored and the device restarts.
1.7
The WPS WLAN Button
You can use the
WPS WLAN ON/OFF
button (
) on the top of the device to turn the
wireless LAN off or on. You can also use it to activate WPS in order to quickly set up a
wireless network with strong security.
ETHERNET
1-4
Green
On
The ZyXEL Device has an Ethernet connection with a device on
the Local Area Network (LAN).
Blinking
The ZyXEL Device is sending/receiving data to /from the LAN.
Off
The ZyXEL Device does not have an Ethernet connection with
the LAN.
WLAN/WPS
Green
On
The wireless network is activated.
Blinking
The ZyXEL Device is communicating with other wireless clients.
Orange
Blinking
The ZyXEL Device is setting up a WPS connection.
Off
The wireless network is not activated.
DSL
Green
On
The DSL line is up.
Blinking
The ZyXEL Device is initializing the DSL line.
Off
The DSL line is down.
INTERNET
Green
On
The ZyXEL Device has an IP connection but no traffic.
Your device has a WAN IP address (either static or assigned by a
DHCP server), PPP negotiation was successfully completed (if
used) and the DSL connection is up.
Blinking
The ZyXEL Device is sending or receiving IP traffic.
Red
On
The ZyXEL Device attempted to make an IP connection but
failed. Possible causes are no response from a DHCP server, no
PPPoE response, PPPoE authentication failed.
Off
The ZyXEL Device does not have an IP connection.
Table 1
LED Descriptions
LED
COLOR
STATUS
DESCRIPTION
Page 37 / 421
Chapter 1 Introducing the ZyXEL Device
P-660HN-FxZ Series User’s Guide
37
1.7.1
Turn the Wireless LAN Off or On
1
Make sure the
POWER
LED is on (not blinking).
2
Press the
WPS WLAN ON/OFF
button for less than five seconds and release it. The
WLAN/WPS
LED should change from on to off or vice versa.
1.7.2
Activate WPS
1
Make sure the
POWER
LED is on (not blinking).
2
Press the
WPS WLAN ON/OFF
button for five to ten seconds and release it. Press the
WPS button on another WPS -enabled device within range of the ZyXEL Device. The
WLAN/WPS
LED should flash while the ZyXEL Device sets up a WPS connection
with the wireless device.
"
You must activate WPS in the ZyXEL Device and in another wireless device
within two minutes of each other. See
Section 7.9.8 on page 129
for more
information.
Page 38 / 421
Chapter 1 Introducing the ZyXEL Device
P-660HN-FxZ Series User’s Guide
38
Page 39 / 421
P-660HN-FxZ Series User’s Guide
39
C
HAPTER
2
Introducing the Web
Configurator
2.1
Overview
The web configurator is an HTML-based management interface that allows easy device setup
and management via Internet browser. Use Internet Explorer 6.0 and later or Netscape
Navigator 7.0 and later versions. The recommended screen resolution is 1024 by 768 pixels.
In order to use the web configurator you need to allow:
•
Web browser pop-up windows from your device. Web pop-up blocking is enabled by
default in Windows XP SP (Service Pack) 2.
•
JavaScript (enabled by default).
•
Java permissions (enabled by default).
See
Appendix B on page 341
if you need to make sure these functions are allowed in Internet
Explorer.
2.1.1
Accessing the Web Configurator
1
Make sure your ZyXEL Device hardware is properly connected (refer to the Quick Start
Guide).
2
Launch your web browser.
3
Type "192.168.1.1" as the URL.
4
A password screen displays. The ZyXEL Device has a dual login system. The default
non-readable characters represents the user password (user by default). Clicking
Login
without entering any password brings you to the system’s status screen. To access the
administrative web configurator and manage the ZyXEL Device, type the admin
password (1234 by default) in the password screen and click
Login
. Click
Cancel
to
revert to the default user password in the password field. If you have changed the
password, enter your password and click
Login
.
Page 40 / 421
Chapter 2 Introducing the Web Configurator
P-660HN-FxZ Series User’s Guide
40
Figure 3
Password Screen
5
The following screen displays if you have not yet changed your password. It is strongly
recommended you change the default password. Enter a new password, retype it to
confirm and click
Apply
; alternatively click
Ignore
to proceed to the main menu if you
do not want to change the password now.
Figure 4
Change Password Screen
6
The following screen displays if you have not replaced the factory default certificate.
Click
Apply
to create a specific certificate for the device using your computer’s MAC
address.
"
For security reasons, the ZyXEL Device automatically logs you out if you do
not use the web configurator for five minutes (default). If this happens, log in
again.

Rate

4 / 5 based on 1 vote.

Popular Zyxel Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top