1. Home
    2. /
  2. Manuals
    3. /
  3. TRENDnet
    4. /
  4. TVP-221H
    5. /
  5. 16
Page 76 / 100 Scroll up to view Page 71 - 75
TVP-221H User’s Guide
Telnet / Console
Web Configuration
Login to Site A TVP Gateway
From Console
1.
Logon to the Web Configuration by
opening your browser
Enter Username “admin”
Enter Password “123”
Enter 192.168.0.20
2.
You will be prompted for Username and
Password. Default Username and
Password are “admin” and “123”
respectively.
or from
Windows command prompt
Enter “telnet 192.168.0.20”
Enter Username “admin”
Enter Password “123”
Web Configuration of Dial Plan
atpm req
Dial Plan Settings / Dial Plan Table Setup
atpm aadd
22 5 5 22 2
3.
Select “Add” and “Telephone
4.
Enter following fields
a.
Telephone Number: 22
b.
Hunt Group ID:
22
76
c.
Min. Digits:
5
d.
Max. Digits:
5
e.
Strip Length:
2
f.
Append Prefix: none
5.
Click on OK
Dial Plan Settings / Dial Plan Table Setup
6.
Select “Add” and “HuntGroup”
atpm hadd
22 2 22
7.
Enter following fields
a.
Hunt Group ID: 22
b.
Destination ID 0: 22
8.
Click on OK
Dial Plan Settings / Dial Plan Table Setup
atpm dadd
20 h323 192.168.0.55
9.
Select “Add” and “DestinationID”
10.
Enter the following fields
a.
Destination ID: 22
b.
Hostname (or IP address)
192.168.0.55
atpm done
atpm store
c.
Click on OK
Dial Plan Settings / Dial in PLAR/CID
set tcid 0 dial_in plar 22201
11.
Enter 22201 in the PLAR Address Field
config activate
12.
Click on OK
config store
Dial Plan Settings / Store Dial Plan
13.
Click on Yes
Liness 3-12 create an
address entry for TVP
Gateway B
Lines 11-13 setup the hotline
(PLAR) from TVP Gateway A
to TVP Gateway B
Page 77 / 100
TVP-221H User’s Guide
6
Chapter 6
Connection Considerations
This section discusses the special connection consideration for various environments and
situations where you can use the VoIP Gateway.
6.1
Port Configuration
VoIP Gateway supports FXS and FXO ports.
FXS (Foreign Exchange Station)
FXS provides power and ringing signals to its interfacing equipment.
It is
not
intended for connection to the Public Switched Telephone Network.
It is a station
loop start operation that provides a connection to:
1.
A standard, single-line analog telephone system
2.
The line circuit of a key telephone system
3.
A loop start trunk circuit of a Private Branch Exchange (PBX) that normally
connects to incoming Central Office circuits
FXO (Foreign Exchange Office)
FXO recognizes signals and draws current to indicate an active state.
It is a trunk
loop start operation that emulates a single-line telephone to:
1. Central Office lines
2. PBX station
There are two basic environments that the TVP-221H can be applied to.
They are
described in the following sections.
77
Page 78 / 100
TVP-221H User’s Guide
78
Application 1: Special FXS Connections
The following diagram illustrates two different types of connections. The SITE A
FXS Connection shows the normal connection between a gateway and telephone
set (POTS) or FAX machine. The other type of FXS connection is shown on SITE
B, on the right hand side. The Connection between the gateway and PBX has a
special CO trunk interface card. The telephone sets connected to PBX can be
either POTS or digital telephone depending upon the PBX capability.
FXS Connection
w/ CO Trunk
Interface Card
TVP-224HR
TVP-221H
Site A
Site B
Normal FXS
Connection
Application 2: FXO Connections
Application 2 has three possible connections. One Site A, the FXS connection to
analog devices is normal and is identical to connections mentioned in Application
1.
On Site B, the connection between PSTN and PBX is also a normal
connection. The last connection is between PBX and the gateway which uses the
internal analogue lines of the PBX. In this case, the FXO port has to be used.
Note
: If a digital PBX is used, an analog terminal adapter is needed to provide an
analog interface to the FXO port. Please consult with your PBX supplier.
In this application, the caller on Site A, can make a call using a device connected
to a FXS port on the Site A gateway.
The call will be routed to the Site B
Gateway,
through a FXO port and passed on to the PBX system. The PBX
system will then forward the call to the dedicated terminal / extension.
TVP-224HR
TVP-221H
Site A
Site B
Normal FXS
Connection
Normal
FXO Connection
Page 79 / 100
TVP-221H User’s Guide
1
7
Chapter 7
Troubleshooting Tips
This section provides solutions for problems you may possibly encounter
while installing and connecting your VoIP Gateway.
Power (PWR) LED is not illuminate
1.
Check the power adapter connection.
2.
If the power adapter or power cord is connected to the gateway, check that the
cord is securely plugged into the power socket on the rear of the console.
3.
Check that the other end of the power adapter or power cord is securely
plugged into the power outlet.
4.
If both ends of the power cord are properly connected and there is still no
power, the gateway might have a faulty power outlet, power adapter, or power
cord.
5.
Change to another power outlet or obtain another power adapter or power cord.
LNK LED is not illuminate
1.
Check the TVP-221H was connected correctly:
a.
Powered on
b.
Correctly connected
2.
Check if the cable connects to an end device is a standard straight through
network Ethernet cable.
3.
Make sure connectors at both ends are securely seated.
4.
Check the TVP-221H IP setting is correct
Line port LED is not illuminate when pick up the phone
1.
Check the RJ11 telephone line is connected correctly between phone set and
line port
There is no dial tone when pick up the phone
2.
Check line port LED illuminate
3.
Check the RJ11 telephone line is connected correctly between phone set and
line port
There is an out-of-service tone when dialing destination phone number
1.
Check the dial plan setting (address table, hunt group table and destination
table) at the destination phone number
There is no connected tone when dialing destination phone number
79
Page 80 / 100
TVP-221H User’s Guide
80
2.
Check the IP network (Ethernet cable, Ethernet port and GW IP setting) is
connected correctly
3.
Check the destination TVP-221H and phone is available
Final Steps
If the procedures in this section have not solved the problem, reset the gateway by
turning the power on and off.
If the problem still exists, contact customer support.

Rate

3.5 / 5 based on 2 votes.

Popular TRENDnet Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top