1. Home
    2. /
  2. Manuals
    3. /
  3. TRENDnet
    4. /
  4. TVP-221H
    5. /
  5. 14
Page 66 / 100 Scroll up to view Page 61 - 65
TVP-221H User’s Guide
66
After these dial plans are added, users on Site A are able to dial “22 +
extension number” to connect to users on site B for free VoIP telephony.
Users on Site B are able to call phones on Site A for free VoIP telephony by
dialing “11 + extension number”. (Note: There is a Max digit (5) limitation on
dial plan which allows the TVP-221H to differentiate with potential PSTN
numbers that may start with 11 or 22 but because they exceed 5 digits, they
would be handled differently)
The benefits of this dial plan are:
1. Simplified setup
2.
VoIP (Free calls to remote site extension)
3.
Simplified dialing ensures easy, direct access to remote extensions.
4.
Simplified dialing makes remote offices and branches feel like local
extensions.
Network Deployment
Two TVP-221H Gateways (Both Gateways are set up with default settings)
1. TVP-221H
A, located site A
2. TVP-221H
B, located on site B.
Register DDNS name for both Dynamic IPs (See Chapter 4)
•
tvp1.dyndns.org (xxx.xxx.xxx)
is applied for TEW-431BRP
on site A
•
tvp2.dyndns.org (xxx.xxx.xxx)
is applied for TEW-431BRP
on site B
Clients used in this topology:
•
TEW-431BRP
on site A has
PPPoE
, and
DDNS
clients enabled
•
TEW-431BRP
on site B has
DHCP
, and
DDNS
clients enabled.
Other considerations for this configuration:
•
TVP-221H on site A is connected to a
LAN port
, Virtual Server is
enabled.
•
TVP-221H on site B is connected to a
LAN port,
Virtual Server is
enabled.
Page 67 / 100
TVP-221H User’s Guide
TVP-221H configuration (ADSL PPPoE connection) on site A
Web Configuration
Telnet / Console
Local (from PC in same Segment)
Open your browser
1. Enter 192.168.0.1
2.
You will be prompted for
Username and Password. Default
Username and Password are
“admin” and “123” respectively.
Web Configuration of Internet Access
Internet Access / Fixed IP
Enter Fixed IP (192.168.0.20,
Subnet Mask(255.255.255.0),
Default Gateway 192.168.0.254.
3. Click on ‘Save”
67
Console
Connect RS-232 to TVP-221H & PC
Open Hyper Terminal
Input parameters:
Baud rate
19,200
Number of data bit
8
Parity check
None
Number of stop bit
1
Flow control
None
Enter “123”
Telnet (from PC in same Segment)
From Windows command prompt
Enter “telnet 192.168.0.1”
Enter Username “admin”
Enter “123”
net set ip
192.168.0.20
net set mask
255.255.255.0
net set gateway
192.168.0.254
Once Internet Access is setup, you could
choose to reboot the TVP-221H, and then
use a PC in the same segment and with a
web browser, access theTVP-221H:
If using the Router’s DHCP Server, make
sure the routers DHCP Server is on and that
the configuring PC and TVP-221H are
DHCP Client enabled.
From the local connection, you could
continue on setting up the dial plan.
However you could choose to reboot,
If you would like your PC and / or TVP-221H
to have a Fixed IP,
Make sure that the their
IP’s do not conflict with the range of IP’s
allocated with the Routers DHCP Server.
Enter “net reset”
Enter “telnet 192.168.0.20”
Enter “telnet tvp1.dyndns.org”
Enter Username “admin”
Enter “123”
Connect your TVP-221H and a PC
directly to your router making sure
they are in the same LAN segment.
From the windows command prompt:
Or from a remote computer
You would then continue as below:
If you are trying to access the TVP-221H
from a PC in the same segment as the TVP-
221H (LAN),
Open your browser and enter
1. Enter 192.168.0.20
If you would like to access the TVP-221H
from the WAN side, from a remote PC with
Internet Access:
2. Enter tvp1.dyndns.org
You will be prompted for Username and
Password. Default Username and Password
are “admin” and “123” respectively.
You could then continue as below:
Page 68 / 100
TVP-221H User’s Guide
Web Configuration of Dial Plan
Dial Plan Settings / Dialplan Table Setup
4.
Select “Add” and “Telephone
5. Enter following fields
g. Telephone Number: 22
h. Hunt Group ID:
22
i.
Min. Digits:
2
j.
Max. Digits:
5
k.
Strip Length:
2
l.
Append Prefix: none
6. Click on “OK”
Dial Plan Settings / Dialplan Table Setup
7.
Select “Add” and “HuntGroup”
8. Enter following fields
m. Hunt Group ID: 22
n.
Destination ID 0: 22
9. Click on “OK”
Dial Plan Settings / Dialplan Table Setup
10. Select “Add” and “DestinationID”
11. Enter the following fields
o. Destination ID: 22
p.
Hostname (or IP address)
tvp2.dyndns.org
q. Click on “OK”
Dial Plan Settings / Store Dial Plan
12. Click on “Yes”
atpm req
atpm aadd
22 2 5 22 2
atpm hadd
22 2 22
atpm dadd
22 dns tvp2.dyndns.org
atpm done
atpm store
Changes to network settings require rebooting to take effect.
Changes to the Dial Plan do not and will take effect as soon
as they are stored.
Caution
: If you do not store the dial plan, it will be lost
when you reboot.
Note
:
After changing the default IP address, you will be
required to use the new IP Address (hostname), in this
example, 192.168.0.20 to gain access from the local LAN
segment or
tvp1.dyndns.org, to gain remote access via the
Internet.
TVP-221H configuration (cable connection) on site B
Telnet / Console
Web Configuration
Local (from PC in same Segment)
Console
68
Page 69 / 100
TVP-221H User’s Guide
Open your browser
Connect RS-232 to TVP-224HR
and PC
Enter 192.168.01
1.
You will be prompted for
Username and Password.
Default Username and Password
are “admin” and “123”
respectively.
Open Hyper Terminal
Input parameters:
Baud rate
19,200
Number of data bit
8
Parity check
None
Number of stop bit
1
Flow control
None
Enter “123”
Web Configuration of Internet Access
Local Telnet (from PC in same
Internet Access / Fixed IP
Segment)
Enter Fixed IP (192.168.0.55,
Subnet Mask(255.255.255.0),
Default Gateway 192.168.0.254
From Windows command prompt
Enter “telnet 192.168.0.1”
Enter Username “admin”
2. Click on “Save”
Enter “123”
69
net set ip
192.168.0.55
net set mask
255.255.255.0
net set gateway
192.168.0.254
Once Internet Access is setup, you could
choose to reboot the TVP-221H, and then
use a PC in the same segment with a web
browser, to access theTVP-221H:
If using the Router’s DHCP Server, make
sure the routers DHCP Server is on and
that the configuring PC and TVP-221H are
DHCP Client enabled.
If you would like your PC and / or TVP-
221H to have a Fixed IP,
Make sure that
the their IP’s do not conflict with the range
of IP’s allocated with the Routers DHCP
Server.
If you are trying to access the TVP-221H
from a PC in the same segment as the
TVP-221H (LAN),
Open your browser and
enter
3. Enter 192.168.0.55
If you would like to access the TVP-221H
from the WAN side, from a remote PC with
Internet Access:
4. Enter tvp2.dyndns.org
You will be prompted for Username and
Password. Default Username and
Password are “admin” and “123”
respectively.
You could then continue as below:
From the local connection, you
could continue on setting up the
dial plan.
However you could
choose to reboot,
Enter “net reset”
Enter “telnet 192.168.0.55”
Enter “telnet tvp2.dyndns.org”
Enter Username “admin”
Enter “123”
connect your TVP-221H and a
PC directly to your router making
sure they are in the same LAN
segment.
From the windows command
prompt:
Or from a remote computer
You would then continue as
below:
Page 70 / 100
TVP-221H User’s Guide
Web Configuration of Dial Plan
Dial Plan Settings / Dial plan Table Setup
atpm req
3.
Select “Add” and “Telephone
atpm aadd
11 2 5 11 2
4. Enter following fields
r.
Telephone Number:11
s.
Hunt Group ID:
11
t.
Min. Digits:
2
u. Max. Digits:
5
v.
Strip Length:
2
w. Append Prefix: none
5. Click on “OK”
Dial Plan Settings / Dial plan Table Setup
6.
Select “Add” and “HuntGroup”
atpm hadd
11 2 11
7. Enter following fields
f.
Hunt Group ID: 11
g.
Destination ID 0: 11
8. Click on “OK”
Dial Plan Settings / Dial plan Table Setup
9.
Select “Add” and “DestinationID”
atpm dadd
11 dns tvp1.dyndns.org
10. Enter the following fields
h. Destination ID: 11
i.
Hostname (or IP address)
tvp1.dyndns.org
j.
Click on ”OK”
atpm done
Dial Plan Settings / Store Dial Plan
atpm store
11. Click on ”Yes”
70
Changes to network settings require rebooting to take effect.
Changes to the Dial Plan do not and will take effect as soon
as they are stored.
Caution
: If you do not store the dial plan, it will be lost
when you reboot.
Note
:
After changing the default IP address, you will be
required to use the new IP Address (hostname), in this
example, 192.168.0.55 to gain access from the local LAN
segment or
tvp2.dyndns.org, to gain remote access via the
Internet.

Rate

3.5 / 5 based on 2 votes.

Popular TRENDnet Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top