Page 86 / 100 Scroll up to view Page 81 - 85
TVP-221H User’s Guide
86
ping (xxx.xxx.xxx.xxx): 56
data bytes
xxx.xxx.xxx.xxx is alive
If the ping times out, you do not have Internet
Access or the Public IP Address you used is
incorrect.
Please try another Public IP address.
If you confirm that you do not have Internet
Access, please refer to the trouble shooting
section of the User Manual or consult your ISP
to make sure your Internet Access Data is
correct and accurately entered into the TVP-
221H.
The following commands enable / disable web
and telnet access respectively.
Net set http <on/off>
Net set telnet <on/off>
Console>
on / off
To reset to Factory Default settings, please
perform the following commands to:
Erase all 'port', 'codec' & 'h323' configuration
config erase
Then access dial plan edit mode by entering
atpm req
Purge the dial plan from the database
atpm purge all
Store the changes
atpm store
Reset the network configuration to default
net set fac_default
Key in
"yes"
to re-boot.
Page 87 / 100
TVP-221H User’s Guide
87
Appendix C – Connecting Through Telnet
To use Telnet, Internet Access must have been previously setup so that the gateway
is visible on the internet (See User Guide for More Information). Alternatively, you can
use Telnet to locally access the TVP-221H, if you are under a router or switch and the
TVP-221H and your computer are in the same network segment.
To access the TVP-221H Gateway from a remote location / or from the same LAN
Segment using Telnet, perform the following tasks:
Task
Prompt
Type
Open the windows command prompt and enter the
telnet
command followed by the IP address of the TVP-221H
Gateway you want to access.
None
telnet
xxx.xxx.xxx
When the TVP-221H Gateway prompts you to
Login
,
enter the user name "admin”
Login:
admin
When the TVP-221H Gateway prompts you for the
Password
, enter the password. The default password is
"123" but it is recommended that the password be
changed for security considerations.
The password can
be changed from the Web UI Administration / Password
submenu page.
Password
:
123
Type in “ping xxx.xxx.xxx”, where xxx.xxx.xxx is your ISP
provided DNS Server IP or any known Public Internet
Address. The following dialogue confirms Internet Access
Console>ping 168.95.1.1
ping <168.95.1.1>: 56 data bytes
168.95.1.1 is alive
If the ping times out, you do not have Internet Access or
the Public IP Address you pinged is incorrect. Try another
IP Address. If you confirm that you do not have Internet
Access, please refer to the trouble shooting section of the
User Manual or consult your ISP to make sure your
Internet Access Data is correct and accurately entered
into the TVP-221H.
Console>
ping
xxx.xxx.xxx
Page 88 / 100
TVP-221H User’s Guide
88
Appendix D – CLI Commands
Normal Mode Commands
Command
Description
atpm aadd
Add an entry to the address table
atpm adel
Delete an entry from the address table
atpm afind
Find and display an entry in the address table
atpm alist
Display all entries in the address table
atpm dadd
Add an entry to the destination table
atpm ddel
Delete an entry from the destination table
atpm dfind
Find and display an entry in the destination table
atpm dlist
Display all entries in the address table
atpm hadd
Add an entry to the hunt group table
atpm hdel
Delete an entry from the hunt group table
atpm hfind
Find and display an entry in the hunt group table
atpm hlist
Display all entries in the hunt group table
atpm done
End the atpm table update session
atpm erase
Erase all atpm tables from NVS
atpm purge
Purge entries from atpm table(s)
atpm req
Start atpm table update session
atpm restore
Restore atpm tables from NVS
atpm store
Store atpm tables into NVS
atpm slist
Display atpm system parameters
atpm sys
Set atpm system parameters
config activate
Move the configuration from temporary area to active area.
config erase
Erase the configuration from NVS
config store
Store the active configuration data into NVS
clrscr
Clear screen
download
Switch to download mode
help
Display help screen
net reset
Reset the system
Page 89 / 100
TVP-221H User’s Guide
89
net set gateway
Set default gateway’s IP address
net set http
Turn on/off HTTP server
net set ip
Set IP address
net set ip_preced
Set IP precedence bits
net set mask
Set IP subnet mask
net set speed
Select Ethernet link speed
net set user_pw
Set password
net show
Display IP parameters
net show hwstat
Display hardware status
ping
Send ICMP echo request to another host
show h323
Display H.323 parameter settings
show version
Show software versions
set h323
Set H.323 parameters
tel show tel_id
Display line impendence setting.
tel show port
Display hook state for a telephony port
tel show ring_freq
Show ringer’s frequency
tel set tel_id
Set line impendence for GW line interface
tel set ring_freq
Set ringer’s frequency
Download Mode Commands
Command
Description
Help
Display help screen
Quit
Switch to normal operation mode
set gateway
Set default gateway ‘s IP address
set ip
Set IP address
set mask
Set IP subnet mask
start
Start downloading file
Page 90 / 100
TVP-221H User’s Guide
90
Appendix E - Factory Default Settings
The following table lists the settings of certain parameters before the TVP-221H is
shipped.
Parameter
Default Setting
Network
PPPoE
disabled
DYN
DNS
disabled
DHCP client
disabled
Configured IP address
192.168.0.1
Configured IP subnet mask
255.255.255.0
Default gateway IP address
0.0.0.0
Current active IP address
192.168.0.1
Current active subnet mask
255.255.255.0
IP precedence
0 0 0 0
Ethernet MAC address
00-50-2d-xx-xx-xx
Ethernet link speed
10/100 auto-negotiation
User ID for HTTP browser and Telnet client login
admin
Password for HTTP browser and Telnet access
login
123
HTTP server
enabled
Telnet server
enabled
Serial port (Fixed)
Baud rate
19,200
Number of data bit
8
Parity check
None
Number of stop bit
1
Flow control
None
H.323
h323 display_name
customer
h323 h245_term_type
60
h323 rtp_port_base
30,000

Rate

3.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top