1. Home
    2. /
  2. Manuals
    3. /
  3. TRENDnet
    4. /
  4. TVP-221H
    5. /
  5. 12
Page 56 / 100 Scroll up to view Page 51 - 55
TVP-221H User’s Guide
56
The first time you connect to the TVP-221H for configuration, you will need to
connect to it under the same LAN segment to set the DHCP or PPPoE client. To
configure the TVP-221H, insert one end of an Ethernet cable into the RJ45 WAN port
on the rear panel of the TVP-221H and the other end directly to your PC Terminal.
Open your browser and enter the TVP-221H’s default IP Address:
192.160.0.1
. Make
sure your computer’s Fixed IP is in the same segment. (See Chapter 4, PC
Configuration). The TVP-221H supports auto MDIX so you do not have to worry
about the cable. Any Cat 3 or 5 cable will be sufficient.
Dial Plan
After these dial plans are added, users on Site A are able to dial “22 + extension
number” to connect to users on site B for free VoIP telephony. Users on Site B are
able to call phones on Site A for free VoIP telephony by dialing “11 + extension
number”. (Note: There is a Max digit (5) limitation on dial plan which allows the
TVP-221H to differentiate with potential PSTN numbers that may start with 11 or 22
but because they exceed 5 digits, they would be handled differently)
The benefits of this dial plan are:
1.
Simplified setup
2.
VoIP (Free calls to remote site extension)
3.
Simplified dialing ensures easy, direct access to remote extensions.
4.
Simplified dialing makes remote offices and branches feel like local
extensions.
Two TVP-221H Gateways (Both Gateways are set up with default settings)
1.
TVP-221H
A, located site A
2.
TVP-221H
B, located on site B.
Registered DDNS name for both Dynamic IPs
•
tvp1.dyndns.org
is applied for TVP-221H
on site A
•
tvp2.dyndns.org
is applied for TVP-221H
on site B
Clients used on this topology :
•
TVP-221H
on site A has
PPPoE
, and
DDNS
clients enabled
•
TVP-221H
on site B has
DHCP
, and
DDNS
clients enabled.
Network topology is illustrated as follows:
Page 57 / 100
TVP-221H User’s Guide
TVP-221H configuration (ADSL PPPoE connection) on site A
Web Configuration
Telnet / Console
Local (from PC in same Segment)
Open your browser
1. Enter 192.168.0.1
2.
You will be prompted for
Username and Password.
Default Username and
Password are “admin” and
“123” respectively.
Console
Connect RS-232 to TVP-221H and
PC
Open Hyper Terminal
Input parameters:
Baud rate
19,200
Number of data bit
8
Parity check
None
Number of stop bit
1
Flow control
None
Enter “123”
Local Telnet (from PC in same
segment)
From Windows command prompt
57
Page 58 / 100
TVP-221H User’s Guide
Web Configuration of Internet Access
Internet Access / PPPoE
1.
Select “Yes” to enable PPPoE
function
2. Enter username and
password provided by your
ISP
3. Click on “Save”
Internet Access / Dynamic DNS
4. Select Enable
5.
Enter Server Name, Host
Name, User Name, Password
(eg. dyndns.org tvp1
username1 password1)
6. Click on “Save”
7. Click on “Store”
Web Configuration of Dial Plan
Dial Plan Settings / Dial plan Table
Setup
8.
Select “Add” and “Telephone”
9. Enter following fields
a. Telephone Number :22
b. Hunt Group ID:
22
c.
Min. Digits:
2
d. Max. Digits:
5
e. Strip Length:
2
f.
Append Prefix: none
10. Click on “OK”
Enter “telnet 192.168.0.1”
Enter Username “admin”
Enter “123”
net set pppoe on
net set pppoe user_name
[
user_name]
net set pppoe pw
[my_password]
net set dyndns on
set dyndns add [serv_name]
[host_name] [user_name] [password]
(
eg. dyndns.org tvp1 username1
password1)
config activate
config store
58
atpm req
atpm aadd
22 2 5 22 2
atpm hadd
22 2 22
From the local connection, you could
continue setting up the dial plan.
However you could choose to reboot.
Once Internet Access is setup, you could
choose to reboot and then reconnect
using an PC with internet access:
1.
Click on “Reboot”
On your PC, close all browser windows,
before reopening.
2.
Enter tvp1.dyndns.org
3.
You will be prompted for Username
and Password. Default Username
and Password are “admin” and
“123” respectively.
You would then continue as below:
Enter “net reset”
Enter “telnet tvp1.dyndns.org”
Enter Username “admin”
Enter “123”
Using a RJ45 Cat 5 cable, connect your
TVP-221H directly to your ADSL /
Cable Modem and initiate new Telnet
session
from a PC with internet Access:
You would then continue as below:
Page 59 / 100
TVP-221H User’s Guide
Dial Plan Settings / Dial plan Table
Setup
11. Select “Add” and “HuntGroup”
12. Enter following fields
a.
Hunt Group ID: 22
b. Destination ID: 22
13. Click on “OK”
Dial Plan Settings / Dial plan Table
Setup
14. Select “Add” and
“Remote_Host_Name”
15. Enter the following fields
a. Destination ID: 22
b.
Hostname or IP address
(eg. tvp2.dyndns.org)
c.
Click on “OK”
Dial Plan Settings / Store Dial Plan
16. Click on “Store”
17. Click on “Yes”
atpm dadd <
dest_id
> dns
<
hostname/port
> (
eg
.
22 dns
tvp2.dyndns.org)
atpm done
atpm store
TVP-221H configuration (cable connection) on site B
Web Configuration
Telnet / Console
Local (from PC in same Segment)
Open your browser
3. Enter 192.168.0.1
4.
You will be prompted for
Username and Password.
Default Username and
Password are “admin” and
“123” respectively.
59
Console
Connect RS-232 to TVP-221H &
PC
Open Hyper Terminal
Input parameters:
Baud rate
19,200
Number of data bit
8
Parity check
None
Number of stop bit
1
Flow control
None
Enter “123”
Local Telnet (from PC in same
Segment)
Changes to network settings require rebooting to take effect.
Changes to the Dial Plan do not and will take effect as soon
as they are stored.
Caution
: If you do not store the dial plan, it will be lost
when you reboot.
Note
:
After changing the default IP address, you will be
required to use the new IP Address (hostname), in this
example tvp1.dyndns.org, to gain access to the TVP-221H
via web browser user interface or Telnet.
Page 60 / 100
TVP-221H User’s Guide
Web Configuration of Internet Access
Internet Access / DHCP Client
24. Select
“Yes”
25. Click on “Save”
Internet Access / Dynamic DNS
26. Select Enable
27. Enter Server Name, Host
Name, User Name, Password
(eg. dyndns.org tvp2
username2 password2)
28. Click on “Save”
29. Click on “Store”
Web Configuration of Dial Plan
Dial Plan Settings / Dial plan Table
Setup
30. Select “Add” and “Telephone”
31. Enter following fields
a. Telephone Number:11
b. Hunt Group ID:
11
c.
Min. Digits:
2
d. Max. Digits:
5
60
e. Strip Length:
2
f.
Append Prefix: none
32. Click on “OK”
Dial Plan Settings / Dialplan Table
From Windows command prompt
Enter “telnet 192.168.0.1”
Enter Username “admin”
Enter “123”
net set dhcp on
.
net set dyndns on
set dyndns add [serv_name]
[host_name] [user_name] [password]
(eg. dyndns.org tvp2 username2
password2)
config activate
config store
atpm req
atpm aadd
11 2 5 11 2
From the local connection, you could
continue on setting up the dial plan.
However you could choose to reboot,
Once Internet Access is setup, you could
choose to reboot,
1.
Click on “Reboot”
Connect your TVP-221H directly to your
ADSL / Cable Modem. Using a PC with
Internet Access,
close all browser
windows, and then reopen your browser.
2.
Enter tvp2.dyndns.org
3.
You will be prompted for Username
and Password. Default Username and
Password are “admin” and “123”
respectively.
You would then continue as below:
Enter “net reset”
Enter “telnet tvp2.dyndns.org”
Enter Username “admin”
Enter “123”
connect your TVP-221H directly to
your ADSL / Cable Modem and
reconnect from a PC with Internet
Access
You would then continue as below:

Rate

3.5 / 5 based on 2 votes.

Popular TRENDnet Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top