2 - Description and installation of your residential gateway

SAGEM F@st™ 3202 Reference Manual - 288060387-01

Reproduction and communication prohibited without the written permission of

E

Page 2-7

Figure 2.3 - Connecting the ADSL line/Telephone set/Power supply

to the SAGEM F@st™ 3202

2.4

Connecting a set-top box (TV/Video) to your Residential

Gateway

¾

Connect the end of an RJ45/RJ45 cable to the socket marked

ETH2

(

) on your

SAGEM F@st™ 3202,

¾

Connect the other end of the cable to your TV/Video set-top box.

Consult your service provider for how to use your set-top box to access the TV/Video

services with your SAGEM F@st™ 3202.

2 - Description and installation of your residential gateway

SAGEM F@st™ 3202 Reference Manual - 288060387-01

Page 2-8

Reproduction and communication prohibited without the written permission of

E

2.5

Installation instructions

Environment

¾

The SAGEM F@st™ 3202 must be installed and used inside a building.

¾

The ambient temperature must not exceed 45°C.

¾

The SAGEM F@st™ 3202 must not be exposed to strong sunlight or to intense heat.

¾

The SAGEM F@st™ 3202 must not be placed in an environment subject to significant

steam condensation.

¾

The SAGEM F@st™ 3202 must not be exposed to water splashes.

¾

The SAGEM F@st™ 3202 casing must not be covered.

¾

The SAGEM F@st™ 3202 must not be used for outdoor transmissions.

Power source

¾

Use a readily accessible mains outlet, near to the equipment. The power supply lead is 2 m

long.

¾

Arrange the power lead so as to avoid any accidental disconnection of the Residential

Gateway.

¾

The SAGEM F@st™ 3202 is designed to be connected to a TT or TN system power supply.

¾

The SAGEM F@st™ 3202 is not designed to be connected to an electrical installation with

IT system (power supply with independent neutral).

¾

Protection against short circuits and leaks between phase, neutral and earth must be

included in the building's electrical installation. The power supply circuit for this equipment

must be provided with 16 A overcurrent protection as well as differential protection.

Upkeep

¾

Never open the unit. This must be done only by personnel qualified and approved by your

provider.

¾

Do not use liquid or aerosol cleaning agents.

SAGEM F@st™ 3202 Reference Manual - 288060387-01

Reproduction and communication prohibited without the written permission of

E

Page 3-1

3. Installing and configuring the

Residential Gateway

This section

covers

¾

The installation and configuration of your Residential

Gateway on your computer's USB port.

§ 3.1

¾

The installation and configuration of your Residential

Gateway on your computer's network card (Ethernet).

§ 3.2

¾

The installation and configuration of your Residential

Gateway with your computer's Wi-Fi interface.

§ 3.3

¾

The installation and configuration of an additional computer.

§ 3.4

3 - Installing and configuring the residential gateway

SAGEM F@st™ 3202 Reference Manual - 288060387-01

Page 3-2

Reproduction and communication prohibited without the written permission of

E

Your Residential Gateway can be installed and configured with the following interfaces:

¾

USB (see section 3.1),

¾

Ethernet (ETH1

)(see section 3.2),

¾

Wi-Fi (see section 3.3).

!

When you have installed your Residential Gateway with an interface (USB,

for example) and you want to install it with another (Ethernet or Wi-Fi),

you

must uninstall

the Residential Gateway.

To do this:

Select

Start / Programs / LiveBox

/

Utilities

/

Uninstall

.

3.1

Installing and configuring your Residential Gateway on your

computer's USB port

The

USB

port on the SAGEM F@st™ 3202 is a USB 1.1 supporting a maximum bit rate of

12 Mbit/s. The connector provided is type B enabling it to be connected to a computer port

supporting a type A connector via the lead supplied with the equipment.

This port lets you can connect directly to a computer, on a type A USB input using a USB lead

(supplied with the equipment).

The USB interface

must be configured

before the USB connector is

connected.

3.1.1

Installing the USB drivers on your computer

Before installing your SAGEM F@st™ 3202 Residential Gateway, you must

uninstall any other ADSL modem/router.

3 - Installing and configuring the residential gateway

SAGEM F@st™ 3202 Reference Manual - 288060387-01

Reproduction and communication prohibited without the written permission of

E

Page 3-3

3.1.1.1

In Windows XP

The

installation

procedure described was performed in

Windows



XP

.

Installation in other Windows



operating systems (98, ME and 2000) may

differ slightly.

1

Insert the CD-ROM in your computer's

appropriate drive; the screen opposite

appears.

Proceed as described on screen.

Click the

button to

continue installation.

Note:

If this screen does not appear: Select

Start

, then

Run

, then enter:

"<CD-ROM drive letter> :\

autorun.exe

(for example e:\autorun.exe)

then click

OK

.

2

The screen opposite appears.

Click

.

3

The screen opposite appears.

Carry out the operations described on

screen.

Click the

button to

continue installation.