5 - Information / Configuration

SAGEM F@st™ 1704 Reference Manual - 253272861-A

Page 5-25

Sagem Communications SAS

document. Reproduction and disclosure prohibited

Field

Action

Default value

PPP retry on

authentication error

Check the box, PPP can be retried again and

again while authentication fails

Checked

PPP retry period

(seconds)

Enter if required a retry period. This value (in

seconds) is by default set to 15 seconds. You

can set another value from 3 to 65535.

15

PPP MTU (Bytes)

Enter an MTU (

M

aximum

T

ransfer

U

nit) value.

This value (in bytes) is between 38 and 1492.

Note:

The MTU specifies the maximum size

of the data used (IP packets) expressed

as a number of bytes.

1492

Use Static IPv4 Address

Check the box to use the static IPv4 address.

Not checked

IPv4 Address:

7

Enter the static IPv4 address.

0.0.0.0

Use Static IPv6 Address

8

Check the box to use the static IPv6 address.

Not checked

IPv6 Address

9

Enter the static IPv6 address.

-

IPv6 Address Prefix

Length

9

Enter the prefix length for the IPv6 address.

64

Enable PPP Debug mode

Check the box to use the PPP Debug mode.

In the event of connection failure, this option will

enable you to trace a possible problem in the

SYSLOG file.

Not checked

Bridge PPPoE frames

between WAN and Local

Ports

Check the box to enable the router when

bridging the frames between WAN and local

Ethernet ports

Not checked

Enable IGMP Multicast

Proxy

Check the box to activate the IGMP function.

Not checked

•

Click on the

Next

button to continue configuring the remote network (WAN) in PPPoE

mode.

•

Select a preferred wan interface as the system default gateway.

7

This field only appears when the "Use Static IPv4 Address" field is activated (box checked).

8

This field only appears when the “Enable IPv6 for this service” feature is activated (box checked).

9

These fields only appear when the “Use Static IPv6 Address” field is activated (box checked).

5 - Information / Configuration

Page 5-26

SAGEM F@st™ 1704 Reference Manual - 253272861-A

Sagem Communications SAS

document. Reproduction and disclosure prohibited

•

Click on the

Next

button to continue configuring the remote network (WAN) in PPPoE

mode.

Field

Action

Default

value

Obtain DNS info from a

WAN interface

Check the box to obtain DNS server addresses

automatically, and select the desired interface in

the list

WAN Interface selected

.

Checked

Use the following Static

DNS IP address

If you check this box, you must enter DNS

server addresses.

Not

checked

Primary DNS server

Enter a primary DNS server address.

-

Secondary DNS server

Enter a secondary DNS server address.

-

•

Click on the

Next

button to continue configuring the remote network (WAN) in PPPoE

mode.

5 - Information / Configuration

SAGEM F@st™ 1704 Reference Manual - 253272861-A

Page 5-27

Sagem Communications SAS

document. Reproduction and disclosure prohibited

Field

Action

PORT / VPI / VCI

Displays the Port/VPI/VCI specific to the “PPPoE” connection

Connection Type

Displays the “PPPoE” protocol

Service Name

Displays the name of the service: pppoe_0_0_35.

Service Category

Displays the type of service adapted to the traffic required.

IP Address

Indicates that the IP address is allocated automatically:

Automatically assigned

Service State

Displays the status of the service:

Enabled

NAT

Displays the status of the NAT:

Enabled

Firewall

Displays the status of the firewall:

Enabled

IGMP Multicast

Displays the status of the IGMP function:

Disabled

Quality of Service

Displays the status of the Quality of Service function:

Enabled

•

Click on the

Apply/Save

button to confirm the new WAN service.

5 - Information / Configuration

Page 5-28

SAGEM F@st™ 1704 Reference Manual - 253272861-A

Sagem Communications SAS

document. Reproduction and disclosure prohibited

5.7.2.3

Ethernet over ATM – IP over Ethernet (IPoE)

•

Select the WAN service type

IP over Ethernet (IPoE)

.

Field

Action

Default

value

Enter Service description

Displays the name of the service being

configured. This name, which is allocated

automatically, is made up as follows:

Protocol_VPI_ Index _ VCI

For example: ipoe_0_0_35.

Note:

You may enter another service name.

ipoe_0_0_35

Enter 802.1P Priority

10

Enter a value for the 802.1P Priority. This value

is between 0 and 7.

-1

Enter 802.1Q VLAN ID

10

Enter a value for the 802.1QVLAN ID. This

value is between 0 and 4094.

-1

Enable IPv6 for this

service

Check this box to enable IPv6 for this service.

Not checked

•

Click on the

Next

button to continue configuring the WAN service.

10

These values only appear if the WAN service is configured over a DSL ATM interface using VLAN MUX Mode.

5 - Information / Configuration

SAGEM F@st™ 1704 Reference Manual - 253272861-A

Page 5-29

Sagem Communications SAS

document. Reproduction and disclosure prohibited

Field

Action

Default value

Obtain an IP

address

automatically

Check the box to obtain an IP address automatically from

your router's DHCP server.

Checked

Use the following

Static IP address:

If you check this box, you must enter a static WAN IP

address and the dedicated WAN subnet mask and WAN

gateway IP address.

Not checked

WAN IP Address

Enter the static IP address.

-

WAN Subnet Mask

Enter the subnet mask.

-

WAN gateway IP

address

Enter the gateway IP address.

-