Page 66 / 202
                                                    Scroll up to view Page 61 - 65
                                                
                    
5 - Information / Configuration 
Page 5-30
SAGEM F@st™ 1704 Reference Manual - 253272861-A 
Sagem Communications SAS
document. Reproduction and disclosure prohibited 
•
Click on the 
Next
button to continue configuring the remote network (WAN) in IPoE mode. 
Field 
Action 
Default value
Enable IGMP Multicast 
Check the box to activate the IGMP function. 
Not checked
•
Select a preferred wan interface as the system default gateway. 
•
Click on the 
Next
button to continue configuring the remote network (WAN) in IPoE mode. 
 
                 
                                
                    
                        Page 67 / 202
                                            
                    
5 - Information / Configuration 
SAGEM F@st™ 1704 Reference Manual - 253272861-A 
Page 5-31
Sagem Communications SAS
document. Reproduction and disclosure prohibited 
Field 
Action 
Default value
Obtain DNS info from a 
WAN interface 
Check the box to obtain DNS server addresses 
automatically, and select the desired interface in 
the list 
WAN Interface selected
. 
Checked 
Use the following Static 
DNS IP address: 
If you check this box, you must enter DNS server 
addresses. 
Not checked
Primary DNS server 
Enter a primary DNS server address. 
- 
Secondary DNS server 
Enter a secondary DNS server address. 
- 
•
Click on the 
Next
button to continue configuring the remote network (WAN) in IPoE mode. 
 
                 
                                
                    
                        Page 68 / 202
                                            
                    
5 - Information / Configuration 
Page 5-32
SAGEM F@st™ 1704 Reference Manual - 253272861-A 
Sagem Communications SAS
document. Reproduction and disclosure prohibited 
Field 
Action 
PORT / VPI / VCI 
Displays the Port/VPI/VCI specific to the "IPoE" connection. 
Connection Type 
Displays the "IPoE" protocol 
Service Name 
Displays the name of the service: ipoe_0_0_35. 
Service Category 
Displays the type of service adapted to the traffic required. 
IP Address 
Indicates that the IP address is allocated automatically: 
Automatically Assigned 
Service State 
Displays the status of the service: 
Enabled 
NAT 
Displays the status of the NAT: 
Enabled 
Firewall 
Displays the status of the firewall: 
Enabled 
IGMP Multicast 
Displays the status of the IGMP function: 
Disabled 
Quality Of Service 
Displays the status of the Quality Of Service function: 
Enabled
•
Click on the 
Apply/Save
button to confirm the new WAN service. 
 
                 
                                
                    
                        Page 69 / 202
                                            
                    
5 - Information / Configuration 
SAGEM F@st™ 1704 Reference Manual - 253272861-A 
Page 5-33
Sagem Communications SAS
document. Reproduction and disclosure prohibited 
5.7.2.4 
Ethernet over ATM – Bridging 
•
Select the WAN service type 
Bridging
. 
Field 
Action 
Default 
value 
Enter Service description 
Displays the name of the service being 
configured. This name, which is allocated 
automatically, is made up as follows: 
Protocol_VPI_ Index _ VCI 
For example: br_0_0_35. 
Note:
You may enter another service name. 
br_0_0_35 
Enter 802.1P Priority
11
Enter a value for the 802.1P Priority. This value 
is between 0 and 7. 
-1 
Enter 802.1Q VLAN ID
11
Enter a value for the 802.1QVLAN ID. This 
value is between 0 and 4094. 
-1 
Enable IPv6 for this 
service 
Check this box to enable IPv6 for this service. 
Not checked
•
Click on the 
Next
button to continue configuring the remote network (WAN) in Bridge mode. 
11
These values only appear if the WAN service is configured over a DSL ATM interface using VLAN MUX Mode. 
 
                 
                                
                    
                        Page 70 / 202
                                            
                    
5 - Information / Configuration 
Page 5-34
SAGEM F@st™ 1704 Reference Manual - 253272861-A 
Sagem Communications SAS
document. Reproduction and disclosure prohibited 
Field 
Action 
PORT / VPI / VCI 
Displays the Port/VPI/VCI specific to the "Bridge" connection. 
Connection Type 
Displays the "Bridge" protocol 
Service Name 
Displays the name of the service: br_0_0_35. 
Service Category 
Displays the type of service adapted to the traffic required. 
IP Address 
In the “Bridge” connection, this field is: 
Not Applicable 
Service State 
Displays the status of the service: 
Enabled 
NAT 
Displays the status of the NAT: 
Disabled 
Firewall 
Displays the status of the firewall: 
Disabled 
IGMP Multicast 
In the “Bridge” connection, this field is: 
Not Applicable 
Quality Of Service 
Displays the status of the Quality Of Service function: 
Enabled
•
Click on the 
Apply/Save
button to confirm the new WAN service.