5 - Information / Configuration

Page 5-20

SAGEM F@st™ 1704 Reference Manual - 253272861-A

Sagem Communications SAS

document. Reproduction and disclosure prohibited

Field

Action

Default

value

Peak Cell Rate

2

Enter a maximum number of cells transmitted

per second, between 1 and 2491.

-

Sustainable Cell Rate

3

Enter an average number of cells transmitted

per second.

Note:

This number must be lower than the

P

eak

C

ell

R

ate (PCR).

-

Maximum Burst Size

3

Enter the maximum number of cells emitted in

burst (value between 1 and 1000 000).

-

Encapsulation modes

DSL Link type

Action

Default value

EoA

(Ethernet over ATM)

Select the encapsulation of your choice from the

scroll down list.

•

LLC/SNAP-BRIDGING,

•

VC/MUX.

LLC/SNAP-

BRIDGING

PPPoA

(PPP over ATM)

Select the encapsulation of your choice from the

scroll down list.

•

VC/MUX,

•

LLC/ENCAPSULATION.

VC/MUX

IPoA

(IP over ATM)

Select the encapsulation of your choice from the

scroll down list.

•

LLC/SNAP-ROUTING,

•

VC/MUX.

LLC/SNAP-

ROUTING

Select Connection Mode

The Connection Mode selection only appears if you have selected the EoA DSL link type.

Field

Action

Default

value

Default mode

Check this box to configure a single service

over one connection.

Checked

VLAN MUX Mode

Check this box to configure Multiple Vlan

service over one connection.

Not

checked

MSC Mode

Check this box to configure Multiple Service

over one connection.

Not

checked

Enable Quality Of Service

Field

Action

Default

value

Enable Quality Of Service

Check the box to activate the quality of

service.

Not checked

2

This field only appears when the "UBR with PCR", "CBR", "Non Realtime VBR" or "Realtime VBR" type of

service is selected.

3

These fields only appear when the "Non Realtime VBR" or "Realtime VBR" type of service is selected.

5 - Information / Configuration

SAGEM F@st™ 1704 Reference Manual - 253272861-A

Page 5-21

Sagem Communications SAS

document. Reproduction and disclosure prohibited

5.7.2

WAN Service

Object:

This menu is associated with the remote network. It is used to display the list of all the

configured PVCs, and to add PVCs or remove them.

•

In the

Advanced Setup

menu, select

WAN Service

.

The following screen opens:

Field

Meaning

Interface

Name, allocated automatically, associated with the service name (for example,

ATM interface "ppp_0_35_1" associated with the ATM service

pppoe_0_35_1).

Description

Name of the ATM service. This name is made up as follows:

Protocol_VPI_VCI_Index

For example: pppoe_0_35_1.

Type

Data flow encapsulation mode.

Vlan8021p

4

Value of the 802.1P Priority.

VlanMuxId

4

Value of the 802.1Q VLAN ID.

ConnID

Connection Identification. This is used to identify the different PPP

connections which belong to the same PVC. To do so, you need only

increment the "VC number" in the "Service" field when adding a new "PVC".

IGMP

Status (Enabled or Disabled) of the IGMP function. (see Note).

NAT

Status (Enabled or Disabled) of the NAT.

Firewall

Status (Enabled or Disabled) of the Firewall.

IPv6

Status (Enabled or Disabled) of the IPv6.

MLD

Status (Enabled or Disabled) of the MLD.

Note

This function enables the distribution of Multicast datagrams over the local

network (LAN) and interaction between the router and the local network hosts.

4

These values only appear if the WAN service is configured over a DSL ATM interface using VLAN MUX Mode.

5 - Information / Configuration

Page 5-22

SAGEM F@st™ 1704 Reference Manual - 253272861-A

Sagem Communications SAS

document. Reproduction and disclosure prohibited

5.7.2.1

Add

Note

You must have configured a DSL ATM interface (see section 5.7.1) to add a

WAN service.

•

Click on the

Add

button.

•

Select the DSL ATM interface for the WAN service.

•

Click on the

Next

button to continue configuring the WAN service.

Note

Depending on the type of network protocol configured for the selected DSL

ATM interface (EoA, PPPoA or IPoA), the content of the following WAN

interface configuration screens differs.

Therefore, and for more clarity, each type of protocol will be dealt with

separately (screens + associated summary tables) below.

5 - Information / Configuration

SAGEM F@st™ 1704 Reference Manual - 253272861-A

Page 5-23

Sagem Communications SAS

document. Reproduction and disclosure prohibited

5.7.2.2

Ethernet over ATM – PPP over Ethernet (PPPoE)

•

Select the WAN service type

PPP over Ethernet (PPPoE)

.

Field

Action

Default value

Enter Service description

Displays the name of the service being

configured. This name, which is allocated

automatically, is made up as follows:

Protocol_VPI_ Index _ VCI

For example: pppoe_0_0_35.

Note:

You may enter another service name.

pppoe_0_0_35

Enter 802.1P Priority

5

Enter a value for the 802.1P Priority. This value

is between 0 and 7.

-1

Enter 802.1Q VLAN ID

5

Enter a value for the 802.1QVLAN ID. This

value is between 0 and 4094.

-1

Enable IPv6 for this

service

Check this box to enable IPv6 for this service.

Not checked

•

Click on the

Next

button to continue configuring the WAN service.

5

These values only appear if the WAN service is configured over a DSL ATM interface using VLAN MUX Mode.

5 - Information / Configuration

Page 5-24

SAGEM F@st™ 1704 Reference Manual - 253272861-A

Sagem Communications SAS

document. Reproduction and disclosure prohibited

Field

Action

Default value

PPP Username

Enter your connection ID.

This information is provided to you by your

I

nternet

S

ervice

P

rovider (ISP).

-

PPP Password

Enter your connection password.

This information is provided to you by your

I

nternet

S

ervice

P

rovider (ISP).

-

PPPoE Service

Name

Enter the name of the PPPoE service.

This information is provided to you by your

I

nternet

S

ervice

P

rovider (ISP).

-

Authentication

Method

Select the authentication method of your choice from the

scroll down list:

•

AUTO,

•

PAP,

•

CHAP,

•

MSCHAP.

AUTO

Dial on demand

(with idle timeout

timer)

Check the box to only connect to the Internet on "Traffic".

Not checked

Inactivity Timeout

(minutes) [1-4320]:

6

Enter the inactivity time. This value (in minutes) is

between 1 and 4320

(i.e. 72 hours).

If there is no traffic for a certain period of time, the PPPoE

session is interrupted.

0

6

This field only appears when the "Dial on demand (with idle timeout timer)" field is activated (box checked).