Inteno X5668B Router Manual PDF (Setup & Configuration Guide)

Page 51 / 92 Scroll up to view Page 46 - 50

X5668 / X5668U

User’s Guide

46



If the

Network Authentication

is WPA2, select Enable or Disable for

WPA2

Pre-authentication

, enter value of Network Re-Auth Interval, enter value of

WPA

Group Rekey Interval

, the

IP address

and

Port number

of Radius server,

Radius

Key

, WPA Encryption Method (TKIP, AES, TKIP+AES), enable or disable

WEP

encryption

. If WEP Encryption is enabled, select the

Encryption Strength

with

64bits or 128bits, select the current

Key Index

and enter the key and four keys

when necessary.



If the

Network Authentication

is WPA2-PSK (pre-shared key), enter the WPA

Pre-Shared Key and enter

WPA Group Rekey Interval

,

WPA Encryption Method

(TKIP, AES, TKIP+AES), enable or disable

WEP encryption

. If WEP Encryption is

enabled, select the

Encryption Strength

with 64bits or 128bits, select the current

Key Index

and enter the key and four keys when necessary.



If the

Network Authentication

is mixed WPA2/WPA, select Enable or Disable for

WPA2 Pre-authentication

, enter value of Network Re-Auth Interval, enter value of

WPA Group Rekey Interval

, the

IP address

and

Port number

of Radius server,

Radius Key

, WPA Encryption Method (TKIP, AES, TKIP+AES), enable or disable

WEP encryption

. If WEP Encryption is enabled, select the

Encryption Strength

with 64bits or 128bits, select the current

Key Index

and enter the key and four

keys when necessary.

Page 52 / 92

X5668 / X5668U

User’s Guide

47



If the

Network Authentication

is Mixed WPA2/WPA-PSK (pre-shared key), enter

the WPA Pre-Shared Key and enter

WPA Group Rekey Interval

,

WPA Encryption

Method

(TKIP, AES, TKIP+AES), enable or disable

WEP encryption

. If WEP

Encryption is enabled, select the

Encryption Strength

with 64bits or 128bits,

select the current

Key Index

and enter the key and four keys when necessary



Click Save/Apply to save the configuration.

MAC Filter

With this configuration, you could allow or deny wireless to access the device by

wireless MAC address filtering feature. It is disabled as default.

Figure 60: Wireless MAC Filter Configuration

Global Setting



Select the

MAC Restrict Mode

from one of Disable (no MAC filter), Allow (only

those PCs with MAC addresses in the table can surf Internet) and Deny (only

those PCs with MAC addresses in the table can not surf Internet).



Click

Add

to add an entry or

Remove

to remove the specified entry.

Figure 61: Add a Wireless MAC Address

Global Setting



Enter the

MAC Address of wireless client



Click Save/Apply to save the configuration.

Page 53 / 92

X5668 / X5668U

User’s Guide

48

Wireless Bridge

The wireless bridge feature is also known as WDS, Wireless Distribution System).

Figure 62: Wireless Bridge Configuration

Global Setting



Set the

AP mode

as Access Point or Wireless Bridge



When the

AP mode

is set to Wireless Bridge, the

Wireless Restrict

determine

where it can communicate with all other wireless bridges and also wireless

clients (set

Bridge Restrict

is Disabled) or just the specified MAC addresses of

below wireless bridge devices (set

Bridge Restrict

is Enable).



Click Reflash to get the updated information



Click

Save/Apply

to save the configuration

Advanced

This page allows you to configure advanced parameters for wireless communication.

Figure 63: Wireless Setting – Advanced

Page 54 / 92

X5668 / X5668U

User’s Guide

49

Global Setting



Enable

AP Isolation

if you do not want AP to be able to communicate with each

other.



Set the W

ireless Communication Band

. If you do not know it, please it as default.



Select the

channel

from the list



Enter the value of

Auto Channel Timer



Set the

54g Rate

(Wireless Communication Rate), AUTO means to use the

highest rate if possible)



Set the

Rate for Multicast Packets

, AUTO means to use the highest if possible.



Set the

Basic Rate



Set the

Fragmentation Threshold

values from 256 to 2364 bytes. If the value is

too small, it may cause a result in poor performance.



Set the

RTS (Ready to Send) Threshold



Set

DTIM Interval.

DTIM stands for Delivery Traffic Indication Message. This is a

beacon and is a countdown informing wireless clients of the next window for

listening to broadcast and multicast messages. It is a wake-up interval for clients

in power-saving mode.



Set

Beacon Interval

. The interval in milliseconds between beacon transmissions.



Set the

Maximum Associated Wireless Client



Set

XPress Technology

enabled or disabled.



Set

54g Mode

to 54g Auto, 54g Performance, 802.11b, 54g LRS (limited rate

support).



Set

54g Protection

to AUTO if there are 802.11g and 802.11b coexisting in the

wireless network.



Set

Afterburner Technology



Set

Preamble Type

. A preamble is a signal that sync up the timing between

devices.



Set

Transmission Power

. Larger value means more coverage.

Quality of Service

The device provides wireless quality of service, Wi-Fi Multimedia.

Figure 64: Wireless Setting – Quality of Service

Global Setting



Select to enable or disable

WMM (Wi-Fi Multimedia)



Select

to

enable

or

disable

WMM

No

Acknowledgement

.

Enabling

no-acknowledge can result in more efficient throughput but high error rates



Click

Save/Apply

to save the configuration

Page 55 / 92

X5668 / X5668U

User’s Guide

50

Station Information

The table shows up whole associated wireless clients the device and their status.

Figure 65: Wireless Setting – Station Information

Global Setting



Click Refresh to get the latest updated information

Rate

Popular Inteno Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share