Inteno DG201A Router Manual PDF (Setup & Configuration Guide)
Given below is full router user manual of Inteno DG201A router model. You can also download this manual in PDF Format to read later on your computer.
Product user manuals come handy in case you want to know all functionalities of your device, troubleshooting, fist time configuration & setup and in many other situations.
Page 1 / 10
1
Installation
Guide
English
Svenska
Suomi
Norsk
DG201 R1
Multi WAN Residential Gateway
www.inteno.se
Page 2 / 10
3
2
Svenska
Suomi
Norsk
Installation
Guide
English
Language
Page
English
.......................
4
Svenska
.....................
8
Suomi
......................
12
Norsk
.......................
16
DG201 R1
Multi WAN Residential Gateway
Page 3 / 10
5
4
English
Svenska
Suomi
Norsk
DG201
Multi WAN Residential Gateway
Start Box
Check that the following items
are in the Start Box:
• Inteno DG201
• Power adapter
• RJ45 Network cable (white)
(large contact)
• RJ11 Telephone cable (grey)
(small contact)
• DSL splitter
Connecting the
DSL/telephone jack
It’s important to connect the broadband
service to the first telephone jack in your
home. Otherwise you may get trouble with
your telephony service, as well as your
data service. In an apartment you’ll usually
find the first telephone jack close to the
entrance door. In a villa, the location of the
jack may be harder to detect, as you need
to find out where the telephone cable
connects to the house. If you previously
have had a broadband service and it has
worked without troubles you’ll know that
you should install the modem in the same
telephone jack as before. If you haven’t
had a broadband service you’ll need to
localize the first telephone jack.
Do as follows:
1. Shut down your computer.
2. Connect the DSL splitter adapter to the
first telephone jack inside the house.
3. Connect the grey telephone cable
between the DSL splitter and the
DG201 (DSL).
Connecting the WAN/
broadband connection
Do as follows:
1. Shut down your computer.
2. Connect a RJ45 network cable
between your broadband outlet and
the DG201 WAN port (WAN/GbE1).
Back
Top/Front
DG201
Multi WAN Residential Gateway
DG201
Multi WAN Residential Gateway
This installation guide will help you install the Inteno DG201. Your
service provider will supply you with information about log in and
access. DG201 can be connected to an ADSL/VDSL2 network or to an
Ethernet based broadband network.
a
b
c
TEL2
TEL1
LAN1
GbE1
LAN2
LAN3
LAN4
DSL
WiFi
802.11n
WiFi
802.11n
GbE2
d
GbE1 WAN
GbE2 WAN
WLAN
USB
USB 1
USB 2
RESET
Page 4 / 10
7
6
English
Svenska
Suomi
Norsk
Connecting the LAN
1. Connect a RJ45 network cable
between the DG201 network port
(LAN 1-4) and the network port on the
back or side of your computer. If you
have more computers, use LAN2,
LAN3, LAN4 and then GbE2.
2. Finally, plug the power adapter into
an electrical outlet and contact into the
modern where it is labeled “Power.”
3. Start the computer.
4. The colored lights will blink for roughly
30 seconds. If you have connected your
modem properly, the Power, WAN and
Internet lights will be a fixed green color.
See picture labeled “Front.” You have
now connected the DG201.
Connecting the
Wireless Local
Area Network (WLAN)
1. Make sure that the WLAN button on the
front panel is in the ON position.
2. For wireless connection first perform
a search for available wireless networks
using the WLAN client.
3. Compare the list with the SSID which
is shown on a sticker on the under side
of the DG201.
4. Connect by double clicking on the
correct SSID and then providing the
encryption code which is shown on the
sticker labeled WPA on the under side
of the DG201.
Description of
the front panel
Graphics on the front panel
1.
Power indicator light
On (green) – the power is on
On (red) – start up error (contact your
service provider)
Off – the power is off
2.
Ethernet indicator
On (green) – LAN connected
Off – LAN not connected
Blinking (green) – active
3.
GbE1 indicator
On (green) – LAN connected, 100 Mps
On (yellow) – LAN connected, 1000 Mps
Off – LAN not connected
Blinking (green/yellow) - active
4.
TEL1/TEL2
On (green) – the terminal is registered
On (yellow) – the telephone receiver is
off (the telephone is in use)
Blinking (yellow) – incoming call
Off – the telephone receiver is on
(the telephone is not in use)
5.
WLAN indicator
On – (green) WLAN activated
Off – WLAN not active
Blinking (green) – active
6.
USB indicator
On (blue) –
USB connected
Off – USB not active
Blinking (blue) – active
7.
DSL indicator
On (green) – connected to the
DSL network
Off – not connected to the
DSL network
Blinking (green) – active
8.
Internet indicator
On (green) – IP address received
On (red) – IP address not received
9.
GbE1 indicator
On (green) – LAN connected, 100 Mps
On (yellow) – LAN connected, 1000 Mps
Off – LAN not connected
Blinking (green/yellow) – active
Troubleshooting
1. Check that the power is on. The power
indicator light should be on (Power).
See picture labeled “Front.”
2. Is the power indicator light off? Check
that the modem is properly connected
to the power adapter. Check that
the power adapter is connected to an
electrical outlet. If the modem is
properly connected to an electrical
outlet, a power indicator light that is
still not on may indicate a faulty
modem or a faulty power adapter.
Contact your service provider.
3. Are the Power and Internet indicator
lights red? Contact your service
provider.
4. Is the DSL indicator light off? Check
the connection between the DSL port
on the modem and your telephone
jack. If the DSL indicator light is off,
despite proper connection, contact your
service provider.
5. Is your broadband connection is
broken when one of the telephones in
the house is lifted? This probably
means that the modem is not con
nected to the first telephone jack. This
is also the case if there is excessive
static on the line. Move the modem to
the first incoming telephone jack.
6. Is the Ethernet indicator light off?
Check the connection between the
LAN port on the modem and the
network port on the back or side of
your computer. Check that the NIC in
your computer is functioning properly.
7. Reset button. See picture labeled
“Back.” This button resets the modem
to factory settings. Hold it in for
10 seconds.
e
g
h
f
DG201
Multi WAN Residential Gateway
DG201
Multi WAN Residential Gateway
Page 5 / 10
9
English
Svenska
Suomi
Norsk
8
DG201
Multi WAN Residential Gateway
DG201
Multi WAN Residential Gateway
DG201
Multi WAN Residential Gateway
Startboxen
Kontrollera att följande finns
med i startboxen:
• Inteno DG201
• DC-adapter (strömadapter)
• RJ45 Nätverkskabel (vit) (stor kontakt)
• RJ11 Telefonkabel (grå) (liten kontakt)
• DSL splitter.
Inkoppling DSL/
Telefonjacket
Använd första jacket
Det är viktigt att bredbandstjänsten
kopplas till det första telejacket i
bostaden. Annars kan problem uppstå
både på den vanliga telefonin och bred-
bandsuppkopplingen. I en lägenhet sitter
första jacket oftast närmast ytterdörren,
i en villa varierar det beroende på var
telefonledningen går in i huset. Har du
haft bredband tidigare som fungerat
problemfritt kan du vara säker på att
befintlig tjänst sitter i första telejack.
Installera modemet i samma telefonjack
som tidigare bredband varit inkopplat i.
Har du inte haft bredband tidigare
lokalisera ditt första jack.
Gör så här:
1. Stäng av din dator.
2. Koppla DSL splitter i ditt första
inkommande telefonjack.
3. Koppla den grå telefonkabeln
till DSL splitter och DG201
DSL-kontakt (DSL).
Inkoppling WAN/
Bredbandsuttag
Gör så här:
1. Stäng av din dator.
2. Koppla en RJ45 nätverkskabel
mellan ditt bredbandsuttag och DG201
WAN-kontakt märkt WAN/GbE1.
Baksida
Ovansida/
Framsida
Den här installationsguiden hjälper dig att installera Inteno DG201.
Information om hur du loggar in och får åtkomst till dina tjänster
får du från din operatör. DG201 kan dels kopplas in till ett ADSL/VDSL2-
nät alternativt till ett Ethernet-baserat bredbandsnät.
19216811.live