Huawei HG8247H Router Manual PDF (Setup & Configuration Guide)

Page 231 / 358 Scroll up to view Page 226 - 230

3.

Click

Apply

to apply the configuration.

Step 2

Configure the parameters of the H.248-based voice interface.

1.

In the navigation tree, choose

Voice

>

VoIP Interface Configuration

.

2.

In the right pane, configure the parameters of the H.248-based voice interface as follows

(other parameters use the default settings):

l

Set

MGC Address

below

Primary Server

to

200.200.200.200

.

l

MID Format: DomainName

l

MG Domain: 6877687714852901

l

Signaling Port: 1_VOIP_R_VID_20

l

Region: CN – China

NOTE

l

The parameters of the H.248-based voice interface must be consistent with the corresponding

configuration on the media gateway controller (MGC).

l

If dual-homing is configured,

MGC Address

below

Secondary Server

must be configured.

l

MID Format

can be set to

Domain Name

,

IP

, or

Device

. If

MID Format

is set to

Domain Name

or

Device

, the setting must be consistent with the corresponding configuration on the MGC.

l

Domain Name

is ONT's domain name registered on the MGC. It is globally unique.

Domain

Name

in this example is ONT's SN.

l

If

Media Port

is empty, the parameter value is the same as

Signaling Port

. The media streams are

not isolated from signaling streams. If the upper-layer network requires isolation of media streams

from signaling streams, create different traffic streams for the media streams and signaling streams

on the OLT, create different WAN ports on the ONT, and bind the created WAN ports to

Media

Port

and

Signaling Port

.

l

Profile Index

can be set to

Default

,

BT

,

FT

,

KPN

,

PCCW

,

ZTE

, or

BELL

. Choose the value based

on the MGC type.

Profile Index

is set to

Default

(indicating interconnection with Huawei MGC) in

this example. If the settings do not meet requirements, configure

UserDefine

. For details about how

to configure this parameter, contact Huawei technical support.

EchoLife HG8240/HG8245/HG8247 GPON Terminal

Service Manual

3 Configuration

Issue 04 (2011-01-12)

Huawei Proprietary and Confidential

3-193

Page 232 / 358

3.

Click

Apply

to apply the configuration.

Step 3

Configure parameters of the H.248-based voice users.

1.

In the navigation tree, choose

Voice

>

VoIP User Configuration

.

2.

In the right pane, configure the parameters of voice user 1 as follows:

l

Line Name: A0

l

Associated POTS: 1 (binding port TEL1 on the ONT)

l

Select

Enable Line Name

to enable the voice user configuration.

3.

Click

Apply

to apply the configuration.

4.

In the right pane, click

New

to add voice user 2, and configure the parameters of voice user

2 as follows:

l

Line Name: A1

l

Associated POTS: 2 (binding port TEL2 on the ONT)

l

Select

Enable Line Name

to enable the voice user configuration.

5.

Click

Apply

to apply the configuration.

NOTE

l

The terminal IDs

A0

and

A1

must be consistent with the corresponding configuration on the MGC.

l

If

Associated POTS

is

1

, port TEL1 on the ONT is bound. If

Associated POTS

is

2

, port TEL2 on the ONT

is bound.

3 Configuration

EchoLife HG8240/HG8245/HG8247 GPON Terminal

Service Manual

3-194

Huawei Proprietary and Confidential

Issue 04 (2011-01-12)

Page 233 / 358

Step 4

Save the configuration.

Choose

System Tools

>

Configuration File

from the navigation tree. In the right pane, click

Save Configuration

.

Step 5

Restart the voice process.

In the navigation tree, choose

Status

>

VoIP Information

. In the right pane, click

Restart

VoIP

.

Step 6

Check the ONT connection status.

In the navigation tree, choose

Status

>

WAN Information

. In the right pane,

Status

is

Connected

and the obtained IP address is displayed at

IP

.

EchoLife HG8240/HG8245/HG8247 GPON Terminal

Service Manual

3 Configuration

Issue 04 (2011-01-12)

Huawei Proprietary and Confidential

3-195

Page 234 / 358

Step 7

Check the registration status of the voice user.

In the navigation tree, choose

Status

>

VoIP Information

. In the right pane,

User Status

is

Up

.

----End

Result

l

User 1 with telephone number

88001234

can call user 2 with telephone number

88001235

, and the communication between them is normal. The communication is also

normal for user 2's calling user 1.

NOTE

The termination IDs of line 1 and line 2 configured on the MGC correspond to telephone numbers

88001234

and

88001235

respectively.

l

Check whether the voice communication between users using different ONTs is normal.

3.4.7 Configuring the Wi-Fi Access Service on the Web Page

This topic provides an example of how to configure the Wi-Fi access service on the Web page.

Prerequisite

l

The Layer 2 service channels between the OLT and ONTs are enabled by running the OLT

commands. For details, see

3.4.1.1 Enabling Layer 2 Service Channels Between an OLT

and a GPON ONT (on the OLT CLI)

.

l

You have established the environment for logging in to the Web page for service

configuration and have successfully logged in to the Web page. For details, see

3.4.3

Locally Logging in to the Web Interface

.

l

A portable computer with the Wi-Fi function must be available.

3 Configuration

EchoLife HG8240/HG8245/HG8247 GPON Terminal

Service Manual

3-196

Huawei Proprietary and Confidential

Issue 04 (2011-01-12)

Page 235 / 358

Context

The Wi-Fi wireless access service includes the Layer 3 bridge Wi-Fi service and the Layer 3

route Wi-Fi service.

l

Layer 3 Wi-Fi service: Search for the SSID is performed on the PC. After the user passes

the verification, the PPPoE auto dialup is performed on the PC. The IP address is allocated

by the upper-layer BRAS. The ONT is connected to the OLT and then to the upper-layer

network in the Layer 3 mode to provide the high-speed Internet access service.

l

Layer 3 route Wi-Fi service: Search for the SSID is performed on the PC. After the user

passes the verification, the PPPoE auto dialup is performed on the PC. The ONT is

connected to the OLT and then to the upper-layer network in the Layer 3 mode to provide

the high-speed Internet access service.

Procedure

l

Layer 3 bridge Wi-Fi service

1.

Configure the Wi-Fi parameters.

(1)

In the navigation tree, choose

Wi-Fi

>

Wi-Fi Basic Configuration

.

(2)

Select

Enable Wireless

to enable the Wi-Fi function. Then, set the parameters

as follows:

–

SSID: ChinaNet-huawei

–

Authentication Mode: WPA Pre-Shared Key

–

Encryption Mode: TKIP&AES

–

WPA PreSharedKey: chinahuawei

(3)

Click

Apply

to apply the configuration.

2.

Configure the parameters of the Layer 3 bridge WAN port.

(1)

In the navigation tree, choose

WAN

>

WAN Configuration

.

(2)

In the right pane, click

New

. In the dialog box that is displayed, configure

parameters of the WAN port as follows:

–

WAN Connection: Enable

–

Mode: Bridge

EchoLife HG8240/HG8245/HG8247 GPON Terminal

Service Manual

3 Configuration

Issue 04 (2011-01-12)

Huawei Proprietary and Confidential

3-197

Rate

Popular Huawei Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share