Huawei HG8245T Router Manual PDF (Setup & Configuration Guide)

Home

Manuals

Huawei

HG8245T

Page 216 / 429 Scroll up to view Page 211 - 215

huawei(config)#

ont-srvprofile gpon profile-id 10

huawei(config-gpon-srvprofile-10)#

ont-port eth 4 pots 2 catv 1

huawei(config-gpon-srvprofile-10)#

port vlan eth 1 10

After the configurations are complete, run the

commit

command to make the configured

parameters take effect.

huawei(config-gpon-srvprofile-10)#

commit

huawei(config-gpon-srvprofile-10)#

quit

(Optional) Configure an alarm profile.

The ID of the default GPON alarm profile is 1. The thresholds of all the alarm parameters

in the default alarm profile are 0, which indicates that no alarm is reported.

In this example, the default alarm profile is used, and therefore the configuration of the

alarm profile is not required.

Run the

gpon alarm-profile add

command to configure an alarm profile, which is used

for monitoring the performance of an activated ONT line.

Step 4

Add an ONT on the OLT.

The ONT is connected to the GPON port of the OLT through optical fibers. The service can be

configured only after an ONT is successfully added on the OLT.

Two ONTs are connected to GPON port 0/1/1. The ONT IDs are 1 and 2, the SNs are

6877687714852900 and 6877687714852901, the management mode is OMCI, and ONT line

profile 10 and service profile 10 are bound to the two ONTs.

Add an ONT offline.

If the password or SN of an ONT is obtained, you can run the

ont add

command to add

the ONT offline.

huawei(config)#

interface gpon 0/1

huawei(config-if-gpon-0/1)#

ont add 1 1 sn-auth 6877687714852900 omci ont-

lineprofile-id 10 ont-srvprofile-id 10

huawei(config-if-gpon-0/1)#

ont add 1 2 sn-auth 6877687714852901 omci ont-

lineprofile-id 10 ont-srvprofile-id 10

Automatically find an ONT.

If the password or SN of an ONT is unknown, run the

port

portid

ont-auto-find

command

in the GPON mode to enable the ONT auto-find function of the GPON port. Then, run the

ont confirm

command to confirm the ONT.

huawei(config)#

interface gpon 0/1

huawei(config-if-gpon-0/1)#

port 1 ont-auto-find enable

huawei(config-if-gpon-0/1)#

display ont autofind 1

//After this command is executed, the information about all ONTs connected

the GPON port through the optical splitter is displayed.

------------------------------------------------------------------------

Number

: 1

F/S/P

: 0/1/1

Ont SN

: 6877687714852900

Password

VenderID

: HWTC

Ont Version

: 120D0010

Ont SoftwareVersion : V1R003C00

Ont EquipmentID

: 247

Ont autofind time

: 2011-02-10 14:59:10

------------------------------------------------------------------------

Number

: 2

F/S/P

: 0/1/1

Ont SN

: 6877687714852901

Password

VenderID

: HWTC

Ont Version

: 120D0010

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

208

Page 217 / 429

Ont SoftwareVersion : V1R003C00

Ont EquipmentID

: 247

Ont autofind time

: 2011-02-10 14:59:12

------------------------------------------------------------------------

huawei(config-if-gpon-0/1)#

ont confirm 1 ontid 1 sn-auth 6877687714852900 omci

ont-lineprofile-id 10 ont-srvprofile-id 10

huawei(config-if-gpon-0/1)#

ont confirm 1 ontid 2 sn-auth 6877687714852901 omci

ont-lineprofile-id 10 ont-srvprofile-id 10

NOTE

If multiple ONTs of the same type are connected to a port and the same line profile or service profile is

bound to the ONTs, you can add ONTs in batches by confirming the auto discovered ONTs in batches to

simplify the operation and increase the configuration efficiency. For example, the preceding command

can be modified as follows:

huawei(config-if-gpon-0/1)#

ont confirm 1 all sn-auth omci ont-lineprofile-id

10 ont-srvprofile-id 10

(Optional) Bind an alarm profile to the ONT.

In this example, bind the default alarm profile, namely alarm profile 1 to the ONT.

huawei(config-if-gpon-0/1)#

ont alarm-profile 1 1 profile-id 1

huawei(config-if-gpon-0/1)#

ont alarm-profile 1 2 profile-id 1

Step 5

Confirm that the ONT goes online normally.

After an ONT is added, run the

display ont info

command to query the current status of the

ONT. Ensure that

Control flag

of the ONT is

active

Run State

online

Config state

normal

, and

Match state

match

huawei(config-if-gpon-0/1)#

display ont info 1 1

---------------------------------------------------------------------

F/S/P

: 0/1/1

ONT-ID

: 1

Control flag

active

//Indicates that the ONT is

activated.

Run state

online

//Indicates that the ONT goes online

normally.

Config state

normal

//Indicates that the configuration status of

the

ONT is normal.

Match state

match

//Indicates that the capability profile bound

the ONT is consistent with the actual

capability

of the ONT.

...//The rest of the response information is omitted.

If the ONT state fails, the ONT fails to be in the up state, or the ONT does not match, check the

ONT state by referring to the above-mentioned descriptions.

Control flag

deactive

, run the

ont activate

command in the GPON port mode to activate

the ONT.

If the ONT fails to be in the up state, that is,

Run state

offline

, the physical line may be

broken or the optical transceiver may be damaged. You need to check both the material and

the line.

If the ONT state fails, that is,

Config state

failed

, the ONT capability set outmatches the

actual ONT capabilities (For details about the ONT actual capabilities, see Reference of

GPON ONT Capability Sets). In this case, run the

display ont failed-configuration

command in the diagnosis mode to check the failed configuration item and the failure cause.

Then, rectify the fault according to actual conditions.

NOTE

If an ONT supports only four queues, the values of 4–7 of the priority-queue parameter in the

gem add

command are invalid. After configuration recovers, Config state will be failed.

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

209

Page 218 / 429

If the ONT does not match, that is,

Match state

mismatch

, the port types and number of

ports undermatch the actual port types and number of ports supported by the ONT. In this

case, run the

display ont capability

command to query the actual capability of the ONT,

and then select one of the following modes to modify the ONT configuration:

–

Create a proper ONT profile according to the actual capability of the ONT, and then run

the

ont modify

command to modify the configuration data of the ONT.

–

Modify the ONT profile according to the actual capability of the ONT and save the

modification. Then, the ONT automatically recovers the configuration successfully.

Step 6

Specify the native VLAN for the ONT port.

ETH port 1 on the ONT is connected to the PC and the native VLAN is VLAN 10.

NOTE

The

ont port native-vlan

command is used for configuring the native VLAN of an ETH port. When a packet

is transmitted to the ONT, a VLAN tag is added to the packet; when a packet is transmitted out of the ONT, the

VLAN tag is removed from the packet. This command is applicable for only the L2 service (L2 Internet access

service) when the ONT functions as a bridge device. When the ONT functions as a gateway device, the

configuration of the port VLAN is implemented on the ONT Web page, NMS, or U2560 server.

huawei(config-if-gpon-0/1)#

ont port native-vlan 1 1 eth 1 vlan 10

huawei(config-if-gpon-0/1)#

ont port native-vlan 1 2 eth 1 vlan 10

Step 7

Configure traffic profiles.

You can run the

display traffic table ip

command to query the traffic profiles existing in the

system. If the traffic profiles existing in the system do not meet the requirements, you need to

run the

traffic table ip

command to add a traffic profile.

HSI service: The profile ID is 8, the CIR is 4 Mbit/s, the priority is 1, and packets are

scheduled according to the priority carried.

VoIP service: The profile ID is 9, no rate limitation in the upstream and downstream

directions, the priority is 6, and packets are scheduled according to the priority carried.

Wi-Fi service: The profile ID is 10, the CIR is 6 Mbit/s, the priority is 1, and packets are

scheduled according to the priority carried.

U2560 management channel: The profile ID is 11, no rate limitation in the upstream and

downstream directions, the priority is 7, and packets are scheduled according to the priority

carried.

huawei(config-if-gpon-0/1)#

quit

huawei(config)#

traffic table ip index 8 cir 4096 priority 1 priority-policy tag-In-

Package

huawei(config)#

traffic table ip index 9 cir off priority 6 priority-policy tag-In-

Package

huawei(config)#

traffic table ip index 10 cir 6144 priority 1 priority-policy tag-In-

Package

huawei(config)#

traffic table ip index 11 cir off priority 7 priority-policy tag-In-

Package

Step 8

Create service ports.

HSI service: Set the service port indexes to 1 and 2, SVLAN ID to 100, GEM port ID to 1,

and CVLAN ID to 10. Use traffic profile 8.

VoIP service: Set the service port indexes to 3 and 4, SVLAN ID to 200, GEM port ID to 2,

and CVLAN ID to 20. Use traffic profile 9.

Wi-Fi service: Set the service port indexes to 5 and 6, SVLAN ID to 400, GEM port ID to

3, and CVLAN ID to 40. Use traffic profile 10.

U2560 management channel: Set the service port indexes to 7 and 8, SVLAN ID to 500,

GEM port ID to 4, and CVLAN ID to 50. Use traffic profile 11.

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

210

Page 219 / 429

huawei(config)#

service-port 1 vlan 100 gpon 0/1/1 ont 1 gemport 1 multi-service

user-vlan 10 rx-cttr 8 tx-cttr 8

huawei(config)#

service-port 2 vlan 100 gpon 0/1/1 ont 2 gemport 1 multi-service

user-vlan 10 rx-cttr 8 tx-cttr 8

huawei(config)#

service-port 3 vlan 200 gpon 0/1/1 ont 1 gemport 2 multi-service

user-vlan 20 rx-cttr 9 tx-cttr 9

huawei(config)#

service-port 4 vlan 200 gpon 0/1/1 ont 2 gemport 2 multi-service

user-vlan 20 rx-cttr 9 tx-cttr 9

huawei(config)#

service-port 5 vlan 400 gpon 0/1/1 ont 1 gemport 3 multi-service

user-vlan 40 rx-cttr 10 tx-cttr 10

huawei(config)#

service-port 6 vlan 400 gpon 0/1/1 ont 2 gemport 3 multi-service

user-vlan 40 rx-cttr 10 tx-cttr 10

huawei(config)#

service-port 7 vlan 500 gpon 0/1/1 ont 1 gemport 4 multi-service

user-vlan 50 rx-cttr 11 tx-cttr 11

huawei(config)#

service-port 8 vlan 500 gpon 0/1/1 ont 2 gemport 4 multi-service

user-vlan 50 rx-cttr 11 tx-cttr 11

Step 9

Configure the queue scheduling mode.

Use the 3PQ+5WRR queue scheduling. Queues 0-4 adopt the WRR mode, with the weights of

10, 10, 20, 20, and 40 respectively; queues 5-7 adopt the PQ mode.

NOTE

Queue scheduling is a global configuration. You need to configure queue scheduling only once on the OLT, and

then the configuration takes effect globally. In the subsequent phases, you do not need to configure queue

scheduling repeatedly when configuring other services.

huawei(config)#

queue-scheduler wrr 10 10 20 20 40 0 0 0

Configure the mapping between queues and 802.1p priorities. Priorities 0-7 map queues 0-7

respectively.

huawei(config)#

cos-queue-map cos0 0 cos1 1 cos2 2 cos3 3 cos4 4 cos5 5 cos6 6 cos7

For the service board that supports only four queues, the mapping between 802.1p priorities and

queue IDs is as follows: priorities 0 and 1 map queue 1; priorities 2 and 3 map queue 2; priorities

4 and 5 map queue 3; priorities 6 and 7 map queue 4.

Step 10

Save the data.

huawei(config)#

save

----End

Configuration File

vlan 100,200,400,500 smart

vlan attrib 100 stacking

port vlan 100,200,400,500 0/19 0

arp proxy enable

interface vlanif 200

arp proxy enable

quit

dba-profile add profile-id 10 type4 max 102400

dba-profile add profile-id 20 type3 assure 30720 max 102400

dba-profile add profile-id 30 type4 max 204800

dba-profile add profile-id 40 type2 assure 30720

ont-lineprofile gpon profile-id 10

tcont 1 dba-profile-id 10

tcont 2 dba-profile-id 20

tcont 3 dba-profile-id 30

tcont 4 dba-profile-id 40

gem add 1 eth tcont 1

gem add 2 eth tcont 2

gem add 3 eth tcont 3

gem add 4 eth tcont 4

mapping-mode vlan

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

211

Page 220 / 429

gem mapping 1 1 vlan 10

gem mapping 2 2 vlan 20

gem mapping 3 3 vlan 40

gem mapping 4 4 vlan 50

commit

quit

ont-srvprofile gpon profile-id 10

ont-port eth 4 pots 2 catv 1

port vlan eth 1 10

commit

quit

interface gpon 0/1

port 1 ont-auto-find enable

display ont autofind 1

ont confirm 1 ontid 1 sn-auth 6877687714852900 omci ont-lineprofile-id 10 ont-

srvprofile-id 10

ont confirm 1 ontid 2 sn-auth 6877687714852901 omci ont-lineprofile-id 10 ont-

srvprofile-id 10

ont alarm-profile 1 1 profile-id 1

ont alarm-profile 1 2 profile-id 1

ont port native-vlan 1 1 eth 1 vlan 10

ont port native-vlan 1 2 eth 1 vlan 10

quit

traffic table ip index 8 cir 4096 priority 1 priority-policy tag-In-Package

traffic table ip index 9 cir off priority 6 priority-policy tag-In-Package

traffic table ip index 10 cir 6144 priority 1 priority-policy tag-In-Package

traffic table ip index 11 cir off priority 7 priority-policy tag-In-Package

service-port 1 vlan 100 gpon 0/1/1 ont 1 gemport 1 multi-service user-vlan 10 rx-

cttr 8 tx-cttr 8

service-port 2 vlan 100 gpon 0/1/1 ont 2 gemport 1 multi-service user-vlan 10 rx-

cttr 8 tx-cttr 8

service-port 3 vlan 200 gpon 0/1/1 ont 1 gemport 2 multi-service user-vlan 20 rx-

cttr 9 tx-cttr 9

service-port 4 vlan 200 gpon 0/1/1 ont 2 gemport 2 multi-service user-vlan 20 rx-

cttr 9 tx-cttr 9

service-port 5 vlan 400 gpon 0/1/1 ont 1 gemport 3 multi-service user-vlan 40 rx-

cttr 10 tx-cttr 10

service-port 6 vlan 400 gpon 0/1/1 ont 2 gemport 3 multi-service user-vlan 40 rx-

cttr 10 tx-cttr 10

service-port 7 vlan 500 gpon 0/1/1 ont 1 gemport 4 multi-service user-vlan 50 rx-

cttr 11 tx-cttr 11

service-port 8 vlan 500 gpon 0/1/1 ont 2 gemport 4 multi-service user-vlan 50 rx-

cttr 11 tx-cttr 11

queue-scheduler wrr 10 10 20 20 40 0 0 0

cos-queue-map cos0 0 cos1 1 cos2 2 cos3 3 cos4 4 cos5 5 cos6 6 cos7 7

save

3.4.2 Data Plan

This topic plans the data in a unified manner for various example networks of connecting ONTs

in the FTTH GPON access mode. Subsequent examples are configured based on the following

data plan.

Table 3-12

shows the unified data plan for the HSI service, VoIP service and Wi-Fi service in

an FTTH network.

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

212

Rate

Popular Huawei Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share