Huawei HG8245T Router Manual PDF (Setup & Configuration Guide)

Home

Manuals

Huawei

HG8245T

Page 201 / 429 Scroll up to view Page 196 - 200

Ont SN

: 6877687714852901

Password

VenderID

: HWTC

Ont Version

: 120D0010

Ont SoftwareVersion : V1R003C00

Ont EquipmentID

: 247

Ont autofind time

: 2011-02-10 14:59:12

---------------------------------------------------------------------

---

huawei(config-if-gpon-0/1)#

ont confirm 1 ontid 1 sn-auth

6877687714852900 omci ont-lineprofile-id 10 ont-srvprofile-id 10

huawei(config-if-gpon-0/1)#

ont confirm 1 ontid 2 sn-auth

6877687714852901 omci ont-lineprofile-id 10 ont-srvprofile-id 10

NOTE

If multiple ONTs of the same type are connected to a port and the same line profile or service

profile is bound to the ONTs, you can add ONTs in batches by confirming the auto discovered

ONTs in batches to simplify the operation and increase the configuration efficiency. For

example, the preceding command can be modified as follows:

huawei(config-if-gpon-0/1)#

ont confirm 1 all sn-auth omci ont-

lineprofile-id 10 ont-srvprofile-id 10

(3)

(Optional) Bind an alarm profile to the ONT.

In this example, bind the default alarm profile, namely alarm profile 1 to the

ONT.

huawei(config-if-gpon-0/1)#

ont alarm-profile 1 1 profile-id 1

huawei(config-if-gpon-0/1)#

ont alarm-profile 1 2 profile-id 1

Confirm that the ONT goes online normally.

After an ONT is added, run the

display ont info

command to query the current status

of the ONT. Ensure that

Control flag

of the ONT is

active

Run State

online

Config state

normal

, and

Match state

match

huawei(config-if-gpon-0/1)#

display ont info 1 1

---------------------------------------------------------------------

F/S/P

0/1/1

ONT-ID

Control flag

active

//Indicates that the ONT is

activated.

Run state

online

//Indicates that the ONT goes online

normally.

Config state

normal

//Indicates that the configuration status

of the

ONT is normal.

Match state

match

//Indicates that the capability profile

bound to

the ONT is consistent with the

actual capability

of the ONT.

...//The rest of the response information is omitted.

If the ONT state fails, the ONT fails to be in the up state, or the ONT does not match,

check the ONT state by referring to the above-mentioned descriptions.

–

Control flag

deactive

, run the

ont activate

command in the GPON port mode

to activate the ONT.

–

If the ONT fails to be in the up state, that is,

Run state

offline

, the physical line

may be broken or the optical transceiver may be damaged. You need to check both

the material and the line.

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

193

Page 202 / 429

–

If the ONT state fails, that is,

Config state

failed

, the ONT capability set

outmatches the actual ONT capabilities (For details about the ONT actual

capabilities, see Reference of GPON ONT Capability Sets). In this case, run the

display ont failed-configuration

command in the diagnosis mode to check the

failed configuration item and the failure cause. Then, rectify the fault according to

actual conditions.

NOTE

If an ONT supports only four queues, the values of 4–7 of the priority-queue parameter in the

gem add

command are invalid. After configuration recovers, Config state will be failed.

–

If the ONT does not match, that is,

Match state

mismatch

, the port types and

number of ports undermatch the actual port types and number of ports supported

by the ONT. In this case, run the

display ont capability

command to query the

actual capability of the ONT, and then select one of the following modes to modify

the ONT configuration:

–

Create a proper ONT profile according to the actual capability of the ONT, and

then run the

ont modify

command to modify the configuration data of the ONT.

–

Modify the ONT profile according to the actual capability of the ONT and save

the modification. Then, the ONT automatically recovers the configuration

successfully.

Configure a traffic profile.

You can run the

display traffic table ip

command to query the traffic profiles existing

in the system. If the traffic profiles existing in the system do not meet the requirements,

you need to run the

traffic table ip

command to add a traffic profile.

The profile ID is 10, no rate limitation in the upstream and downstream directions,

the priority is 4, and packets are scheduled according to the priority carried.

huawei(config-if-gpon-0/1)#

quit

huawei(config)#

traffic table ip index 10 cir off priority 4 priority-

policy tag-In-Package

Create service ports.

Set the service port indexes to 5 and 6, SVLAN ID to 1000, GEM port ID to 3, and

CVLAN ID to 30. Use traffic profile 10.

huawei(config)#

service-port 5 vlan 1000 gpon 0/1/1 ont 1 gemport 3 multi-

service user-vlan 30 rx-cttr 10 tx-cttr 10

huawei(config)#

service-port 6 vlan 1000 gpon 0/1/1 ont 2 gemport 3 multi-

service user-vlan 30 rx-cttr 10 tx-cttr 10

Configure the queue scheduling mode.

Use the 3PQ+5WRR queue scheduling. Queues 0-4 adopt the WRR mode, with the

weights of 10, 10, 20, 20, and 40 respectively; queues 5-7 adopt the PQ mode.

NOTE

Queue scheduling is a global configuration. You need to configure queue scheduling only once on

the OLT, and then the configuration takes effect globally. In the subsequent phases, you do not need

to configure queue scheduling repeatedly when configuring other services.

huawei(config)#

queue-scheduler wrr 10 10 20 20 40 0 0 0

Configure the mapping between queues and 802.1p priorities. Priorities 0-7 map

queues 0-7 respectively.

huawei(config)#

cos-queue-map cos0 0 cos1 1 cos2 2 cos3 3 cos4 4 cos5 5 cos6

6 cos7 7

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

194

Page 203 / 429

For the service board that supports only four queues, the mapping between 802.1p

priorities and queue IDs is as follows: priorities 0 and 1 map queue 1; priorities 2 and

3 map queue 2; priorities 4 and 5 map queue 3; priorities 6 and 7 map queue 4.

Create a multicast VLAN and set the IGMP version.

Set the IGMP version of the multicast VLAN to IGMP v3.

huawei(config)#

multicast-vlan 1000

huawei(config-mvlan1000)#

igmp version v3

This operation will delete all programs in current multicast vlan

Are you sure to change current IGMP version? (y/n)[n]:

10.

Select the IGMP mode.

Select the IGMP proxy mode.

huawei(config-mvlan1000)#

igmp mode proxy

Are you sure to change IGMP mode?(y/n)[n]:

11.

Add an IGMP upstream port.

The IGMP upstream port is port 0/19/0 and works in the default mode, and protocol

packets are transmitted to all the IGMP upstream ports in the multicast VLAN.

huawei(config-mvlan1000)#

igmp uplink-port 0/19/0

huawei(config-mvlan1000)#

btv

huawei(config-btv)#

igmp uplink-port-mode default

Are you sure to change the uplink port mode?(y/n)[n]:

12.

(Optional) Set the multicast global parameters.

In this example, the default settings are used for all the multicast global parameters.

13.

Configure the program library.

Configure the IP address of the multicast program to 224.1.1.10, program name to

program1, IP address of the program source to 10.10.10.10.

huawei(config-btv)#

multicast-vlan 1000

huawei(config-mvlan1000)#

igmp program add name program1 ip 224.1.1.10

sourceip 10.10.10.10

14.

Configure the right profile.

Configure the profile name to profile0, with the right of watching program 1.

huawei(config-mvlan1000)#

btv

huawei(config-btv)#

igmp profile add profile-name profile0

huawei(config-btv)#

igmp profile profile-name profile0 program-name

program1 watch

15.

Configure the multicast users.

Configure users of service ports 5 and 6 as multicast users and bind right profile

profile0 to the service ports.

huawei(config-btv)#

igmp policy service-port 5 normal

huawei(config-btv)#

igmp policy service-port 6 normal

huawei(config-btv)#

igmp user add service-port 5 auth

huawei(config-btv)#

igmp user add service-port 6 auth

huawei(config-btv)#

igmp user bind-profile service-port 5 profile-name

profile0

huawei(config-btv)#

igmp user bind-profile service-port 6 profile-name

profile0

huawei(config-btv)#

multicast-vlan 1000

huawei(config-mvlan1000)#

igmp multicast-vlan member service-port 5

huawei(config-mvlan1000)#

igmp multicast-vlan member service-port 6

huawei(config-mvlan1000)#

quit

16.

Save the data.

huawei(config)#

save

Configure an optical network terminal (ONT) on the Web page.

Layer 3 bridge mode is used for connecting an ONT to the upper-layer device and

parameters of a WAN port must be configured.

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

195

Page 204 / 429

(1)

Configure the IP address of the PC network adapter to be in the same network

segment as the IP address of the local maintenance Ethernet port of the ONT

(default:

192.168.100.1

(2)

Open the Web browser, and enter the IP address of the local maintenance Ethernet

port of the ONT.

(3)

On the login window, enter the user name (default:

telecomadmin

) and password

(default:

admintelecom

) of the administrator. After the password authentication

is passed, the Web configuration window is displayed.

Configure the working mode of a LAN port.

(1)

In the navigation tree, choose

LAN

LAN Port Work Mode

. Select the check

box of LAN3 and set LAN3 to work in the Layer 3 mode.

(2)

Click

Apply

to apply the configuration.

Configure parameters of a WAN port.

(1)

In the navigation tree, choose

WAN

WAN Configuration

(2)

In the right pane, click

New

. In the dialog box that is displayed, configure

parameters of a WAN port as follows:

–

WAN Connection: Enable

–

Mode: Bridge

–

VLAN ID: 30 (The VLAN ID of the ONT must be the same as the user-side

VLAN ID configured on the OLT.)

–

802.1p: 4

–

MultiCast VLAN ID: 1000 (The multicast VLAN ID of the ONT must be the

same as the multicast VLAN ID configured on the OLT.)

–

Bridge Type: IP_Bridged

–

Binding options: LAN3

(3)

Click

Apply

to apply the configuration.

Enable DHCP replay.

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

196

Page 205 / 429

(1)

In the navigation tree, choose

LAN

DHCP Server Configuration

(2)

In the right pane, click the check box of

Enable DHCP L2Relay

NOTE

Bridge Type

of the WAN port is set to

PPPoE_Bridged

, DHCP relay does not need to be

enabled. If

Bridge Type

is set to

IP_Bridged

, DHCP relay must be enabled.

(3)

Click

Apply

to apply the configuration.

Save the configuration.

In the navigation tree, choose

System Tools

Configuration File

. In the right pane,

click

Save Configuration

to save the configuration.

Configure the ONT on the U2000.

Layer 3 bridge mode is used for connecting the ONT to the upper-layer device and

parameters of a WAN port must be configured.

The following uses batch configurations of creating a value-added service profile of the

ONT as an example. To configure an ONT, on the GPON ONU tab page, select an ONT,

right-click, and choose

Configure Value-Added Service

from the shortcut menu.

Configure the value-added service profile of the ONT.

(1)

From the main menu, choose

Configuration

Access Profile Management

. In

the navigation tree of the tab page that is displayed, choose

PON Profile

ONT

VAS Profile

(2)

On the

ONT VAS Profile

tab page, right-click, and choose

Add

from the shortcut

menu.

(3)

In the dialog box that is displayed, set relevant parameters.

–

Profile Name: ONT-IPTV

–

Vendor ID: HWTC(2011)

–

Terminal Type: 247

–

Version: V1R002C06-Later

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

197

Rate

Popular Huawei Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share