Huawei HG8245T Router Manual PDF (Setup & Configuration Guide)

Page 156 / 429 Scroll up to view Page 151 - 155

(6)

Configure a routing policy.

a.

In the navigation tree, choose

Layer 3 Forwarding

>

Policy Route

. Select

Policy Route

, right-click, and choose

Add

.

b.

Choose

Policy Route 1

and enter proper values.

–

Physical Port Name: LAN1

–

WAN Interface Name: WAN1(ONT-HSI)

NOTE

To bind a LAN port to a WAN port, set

Physical Port Name

and

WAN Interface

Name

. The preceding figure shows that WAN 1 is bound to LAN 1.

To bind a WAN port to multiple LAN ports, set

Physical Port Name

to

LAN1,...,LANx

. For example, to bind WAN 1 to LAN 1 and LAN 2, set

Physical Port

Name

to

LAN1,LAN2

.

(7)

Click

OK

to complete the configuration of the new profile.

3.

Bind the value-added service profile.

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

148

Page 157 / 429

(1)

In the

Physical Map

navigation tree on the

Main Topology

tab page, double-

click the target OLT, or select the target OLT, right-click, and choose

NE

Explorer

.

(2)

In the navigation tree, choose

GPON

>

GPON Management

.

(3)

In the window on the right, choose

GPON ONU

.

(4)

On the

GPON ONU

tab page, set the search criteria to find the GPON ONU

records.

(5)

Select an ONT from the list, right-click, and choose

Bind VAS Profile

from the

shortcut menu. In the dialog box that is displayed, choose the created profile, and

click

OK

to complete profile binding.

4.

Configure the ONT value-added service.

(1)

On the

GPON ONU

tab page, select an ONT, right-click, and choose

Configure

Value-Added Service

from the shortcut menu.

(2)

Configure the user name and password for PPPoE dialup.

In the navigation tree, choose

WAN Device

>

WAN Device 1

>

WAN

Connection

>

WAN Connection 1

>

WAN PPP Interface

>

WAN PPP

Interface 1

. Select

WAN PPP Interface 1

, and set

User Name

to

iadtest@pppoe

and

Password

to

iadtest

. The user name and password must be

the same as those configured on the BRAS.

(3)

Click

OK

. In the dialog box that is displayed, click

OK

. The configurations take

effect without the requirement of resetting the ONT.

----End

Result

The PC obtains the IP addresses automatically. After the PPPoE dialup is successfully performed

on the ONT, the PC can automatically obtain the IP addresses allocated by the ONT through

DHCP. Then, the Internet access service is provisioned after Websites are entered into Internet

Explorer (IE) address bars of the PC.

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

149

Page 158 / 429

Configuration File

vlan 100 smart

vlan attrib 100 stacking

port vlan 100 0/19 0

dba-profile add profile-id 10 type4 max 102400

ont-lineprofile gpon profile-id 10

tcont 4 dba-profile-id 10

gem add 1 eth tcont 4

mapping-mode vlan

gem mapping 1 0 vlan 10

commit

quit

ont-srvprofile gpon profile-id 10

ont-port eth 4 pots 2 catv 1

commit

quit

interface gpon 0/1

port 1 ont-auto-find enable

display ont autofind 1

ont confirm 1 ontid 1 sn-auth 6877687714852900 omci ont-lineprofile-id 10 ont-

srvprofile-id 10ont confirm 1 ontid 2 sn-auth 6877687714852901 omci ont-lineprofile-

id 10 ont-srvprofile-id 10ont alarm-profile 1 1 profile-id 1

ont alarm-profile 1 2 profile-id 1

quit

traffic table ip index 8 cir 4096 priority 1 priority-policy tag-In-Package

service-port 1 vlan 100 gpon 0/1/1 ont 1 gemport 1 multi-service user-vlan 10 rx-

cttr 8 tx-cttr 8

service-port 2 vlan 100 gpon 0/1/1 ont 2 gemport 1 multi-service user-vlan 10 rx-

cttr 8 tx-cttr 8

queue-scheduler wrr 10 10 20 20 40 0 0 0

cos-queue-map cos0 0 cos1 1 cos2 2 cos3 3 cos4 4 cos5 5 cos6 6 cos7 7

save

3.3.4 Configuring the GPON FTTH VoIP Service (H.248 Protocol)

on the OLT CLI

The OLT is connected to the remote ONT through a GPON port to provide users with the IP-

based high-quality and low-cost VoIP service.

Service Requirements

l

The ONT is connected to the MGC through H.248.

l

The ONT obtains the IP address through DHCP.

l

Two phone sets are connected to two TEL ports of the ONT respectively, and calls can be

made between two phone sets.

l

Users of phone sets under different ONTs can call and communicate with each other.

l

The DBA mode of the VoIP service is assured bandwidth + maximum bandwidth, and no

rate limitation is performed on the upstream and downstream traffic.

Table 3-7

Data plan

Item

Data

OLT

S-VLAN ID: 200

S-VLAN type: smart VLAN

Upstream port: 0/19/0

C-VLAN ID: 20

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

150

Page 159 / 429

Item

Data

ONT

ONT ID: 1 and 2

IP address of the MGC server: 200.200.200.200/24

Port ID of the MGC server: 2944

MG registration mode: domain name

MG domain name: 6877687714852901

Terminal IDs of line 1 and line 2: A0 and A1

Prerequisite

l

The interface data and the PSTN user data corresponding to the MG interface must be

configured on the MGC.

l

The OLT must be connected to the MGC. The IP address of the MGC server can be pinged

from the OLT.

l

For the ONT, to provision different voice services, you must select different software

versions. Before configuration, ensure that the ONT's version is V200R005C01.

Procedure

l

Configure the OLT.

1.

Create a service VLAN and add an upstream port to it.

The VLAN ID is 200, and the VLAN is a smart VLAN. Add upstream port 0/19/0 to

VLAN 200.

huawei(config)#

vlan 200 smart

huawei(config)#

port vlan 200 0/19 0

2.

(Optional) Configure upstream link aggregation.

In this example, a single upstream port is used. In the case of multiple upstream ports,

upstream link aggregation can be configured. For details, see Configuring Upstream

Link Aggregation.

3.

Enables ARP proxy.

For different users of the same SVLAN, because the service ports of the smart VLAN

are isolated from each other, the voice media streams cannot interchange normally.

Therefore, the ARP proxy function of the OLT needs to be enabled.

huawei(config)#

arp proxy enable

huawei(config)#

interface vlanif 200

huawei(config-if-vlanif200)#

arp proxy enable

huawei(config-if-vlanif200)#

quit

4.

Configure GPON ONT profiles.

GPON ONT profiles include the DBA profile, line profile, service profile, and alarm

profile.

–

DBA profile: A DBA profile describes the GPON traffic parameters. A T-CONT

is bound to a DBA profile for dynamic bandwidth allocation, improving the

upstream bandwidth usage rate.

–

Line profile: A line profile describes the binding between the T-CONT and the

DBA profile, the QoS mode of the traffic stream, and the mapping between the

GEM port and the ONT-side service.

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

151

Page 160 / 429

–

Service profile: A service profile provides the service configuration channel for

the ONT that is managed through OMCI.

–

Alarm profile: An alarm profile contains a series of alarm thresholds to measure

and monitor the performance of activated ONT lines. When a statistical value

reaches the threshold, the host is notified and an alarm is reported to the log host

and the NMS.

(1)

Configure a DBA profile.

Run the

display dba-profile

command to query the existing DBA profiles in the

system. If the existing DBA profiles in the system do not meet the requirement,

run the

dba-profile add

command to create a DBA profile.

Set the DBA profile ID to 20, type to Type3, assured bandwidth to 15 Mbit/s,

and maximum bandwidth to 30 Mbit/s.

huawei(config)#

dba-profile add profile-id 20 type3 assure 15360 max

30720

(2)

Configure an ONT line profile.

Create GPON ONT line profile 10 and bind T-CONT 2 to DBA profile 20.

huawei(config)#

ont-lineprofile gpon profile-id 10

huawei(config-gpon-lineprofile-10)#

tcont 2 dba-profile-id 20

Create GEM port 2 for carrying traffic streams of the ETH type and bind GEM

port 2 to T-CONT 2. Set the QoS mode to priority-queue (default).

NOTE

a.

To change the QoS mode, run the

qos-mode

command to configure the QoS mode to gem-

car or flow-car, and run the

gem add

command to configure the ID of the traffic profile

bound to the GEM port.

b.

When the QoS mode is PQ, the default queue priority is 0; when the QoS is flow-car,

traffic profile 6 is bound to the port by default (no rate limitation); when the QoS mode is

gem-car, traffic profile 6 is bound to the port by default (no rate limitation).

huawei(config-gpon-lineprofile-10)#

gem add 2 eth tcont 2

Configure the mapping between the GEM port and the ONT-side service to the

VLAN mapping mode (default) and map the service port of CVLAN 20 to GEM

port 2.

huawei(config-gpon-lineprofile-10)#

mapping-mode vlan

huawei(config-gpon-lineprofile-10)#

gem mapping 2 1 vlan 20

After the configurations are complete, run the

commit

command to make the

configured parameters take effect.

huawei(config-gpon-lineprofile-10)#

commit

huawei(config-gpon-lineprofile-10)#

quit

(3)

Configure an ONT service profile.

The number of ports configured in the service profile must be the same as the

actual number of ONT ports. The flowing table lists the port capabilities

ofHG8010/HG8240B/HG8245T/HG8247T. The HG8247 is used as an example.

Product

Number of

ETH Ports

Number of

POTS Ports

Number of

CATV Ports

HG8010

1

-

HG8240/

HG8240B

4

2

-

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

152

Rate

Popular Huawei Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share