Huawei HG8245T Router Manual PDF (Setup & Configuration Guide)

Home

Manuals

Huawei

HG8245T

Page 141 / 429 Scroll up to view Page 136 - 140

–

DBA profile: A DBA profile describes the GPON traffic parameters. A T-CONT

is bound to a DBA profile for dynamic bandwidth allocation, improving the

upstream bandwidth usage rate.

–

Line profile: A line profile describes the binding between the T-CONT and the

DBA profile, the QoS mode of the traffic stream, and the mapping between the

GEM port and the ONT-side service.

–

Service profile: A service profile provides the service configuration channel for

the ONT that is managed through OMCI.

–

Alarm profile: An alarm profile contains a series of alarm thresholds to measure

and monitor the performance of activated ONT lines. When a statistical value

reaches the threshold, the host is notified and an alarm is reported to the log host

and the NMS.

(1)

Configure a DBA profile.

You can run the

display dba-profile

command to query the DBA profiles

existing in the system. If the DBA profiles existing in the system do not meet the

requirements, you need to run the

dba-profile add

command to add a DBA

profile.

Set the DBA profile ID to 10, type to type4, and maximum bandwidth to 100

Mbit/s.

huawei(config)#

dba-profile add profile-id 10 type4 max 102400

(2)

Configure an ONT line profile.

Create GPON ONT line profile 10 and bind T-CONT 4 to DBA profile 10.

huawei(config)#

ont-lineprofile gpon profile-id 10

huawei(config-gpon-lineprofile-10)#

tcont 4 dba-profile-id 10

Create GEM port 1 for carrying traffic streams of the ETH type and bind GEM

port 1 to T-CONT 4. Set the QoS mode to priority-queue (default).

NOTE

To change the QoS mode, run the

qos-mode

command to configure the QoS mode to gem-

car or flow-car, and run the

gem add

command to configure the ID of the traffic profile

bound to the GEM port.

When the QoS mode is PQ, the default queue priority is 0; when the QoS is flow-car,

traffic profile 6 is bound to the port by default (no rate limitation); when the QoS mode is

gem-car, traffic profile 6 is bound to the port by default (no rate limitation).

huawei(config-gpon-lineprofile-10)#

gem add 1 eth tcont 4

Configure the service mapping mode from the GEM port to the ONT to VLAN

(default), and map CVLAN 10 to GEM port 1.

huawei(config-gpon-lineprofile-10)#

mapping-mode vlan

huawei(config-gpon-lineprofile-10)#

gem mapping 1 0 vlan 10

After the configurations are complete, run the

commit

command to make the

configured parameters take effect.

huawei(config-gpon-lineprofile-10)#

commit

huawei(config-gpon-lineprofile-10)#

quit

(3)

Configure an ONT service profile.

The ID of the VLAN to which ETH port 1 belongs is 10.

The number of ports configured in the service profile must be the same as the

actual number of ONT ports. The flowing table lists the port capabilities

ofHG8010/HG8240B/HG8245T/HG8247T. The HG8247 is used as an example.

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

133

Page 142 / 429

Product

Number of

ETH Ports

Number of

POTS Ports

Number of

CATV Ports

HG8010

HG8240/

HG8240B

HG8242

HG8245/

HG8245T

HG8247/

HG8247T

huawei(config)#

ont-srvprofile gpon profile-id 10

huawei(config-gpon-srvprofile-10)#

ont-port eth 4 pots 2 catv 1

huawei(config-gpon-srvprofile-10)#

port vlan eth 1 10

After the configurations are complete, run the

commit

command to make the

configured parameters take effect.

huawei(config-gpon-srvprofile-10)#

commit

huawei(config-gpon-srvprofile-10)#

quit

(4)

(Optional) Configure an alarm profile.

–

The ID of the default GPON alarm profile is 1. The thresholds of all the alarm

parameters in the default alarm profile are 0, which indicates that no alarm is

reported.

–

In this example, the default alarm profile is used, and therefore the

configuration of the alarm profile is not required.

–

Run the

gpon alarm-profile add

command to configure an alarm profile,

which is used for monitoring the performance of an activated ONT line.

Add an ONT on the OLT.

The ONT is connected to the GPON port of the OLT through optical fibers. The service

can be configured only after an ONT is successfully added on the OLT.

Two ONTs are connected to GPON port 0/1/1. The ONT IDs are 1 and 2, the SNs are

6877687714852900 and 6877687714852901, the management mode is OMCI, and

ONT line profile 10 and service profile 10 are bound to the two ONTs.

(1)

Add an ONT offline.

If the password or SN of an ONT is obtained, you can run the

ont add

command

to add the ONT offline.

huawei(config)#

interface gpon 0/1

huawei(config-if-gpon-0/1)#

ont add 1 1 sn-auth 6877687714852900 omci

ont-lineprofile-id 10 ont-srvprofile-id 10

huawei(config-if-gpon-0/1)#

ont add 1 2 sn-auth 6877687714852901 omci

ont-lineprofile-id 10 ont-srvprofile-id 10

(2)

Automatically find an ONT.

If the password or SN of an ONT is unknown, run the

port

portid

ont-auto-

find

command in the GPON mode to enable the ONT auto-find function of the

GPON port. Then, run the

ont confirm

command to confirm the ONT.

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

134

Page 143 / 429

huawei(config)#

interface gpon 0/1

huawei(config-if-gpon-0/1)#

port 1 ont-auto-find enable

huawei(config-if-gpon-0/1)#

display ont autofind 1

//After this command is executed, the information about all ONTs

connected to

the GPON port through the optical splitter is displayed.

---------------------------------------------------------------------

---

Number

: 1

F/S/P

: 0/1/1

Ont SN

: 6877687714852900

Password

VenderID

: HWTC

Ont Version

: 120D0010

Ont SoftwareVersion : V1R003C00

Ont EquipmentID

: 247

Ont autofind time

: 2011-02-10 14:59:10

---------------------------------------------------------------------

---

Number

: 2

F/S/P

: 0/1/1

Ont SN

: 6877687714852901

Password

VenderID

: HWTC

Ont Version

: 120D0010

Ont SoftwareVersion : V1R003C00

Ont EquipmentID

: 247

Ont autofind time

: 2011-02-10 14:59:12

---------------------------------------------------------------------

---

huawei(config-if-gpon-0/1)#

ont confirm 1 ontid 1 sn-auth

6877687714852900 omci ont-lineprofile-id 10 ont-srvprofile-id 10

huawei(config-if-gpon-0/1)#

ont confirm 1 ontid 2 sn-auth

6877687714852901 omci ont-lineprofile-id 10 ont-srvprofile-id 10

NOTE

If multiple ONTs of the same type are connected to a port and the same line profile or service

profile is bound to the ONTs, you can add ONTs in batches by confirming the auto discovered

ONTs in batches to simplify the operation and increase the configuration efficiency. For

example, the preceding command can be modified as follows:

huawei(config-if-gpon-0/1)#

ont confirm 1 all sn-auth omci ont-

lineprofile-id 10 ont-srvprofile-id 10

(3)

(Optional) Bind an alarm profile to the ONT.

In this example, bind the default alarm profile, namely alarm profile 1 to the

ONT.

huawei(config-if-gpon-0/1)#

ont alarm-profile 1 1 profile-id 1

huawei(config-if-gpon-0/1)#

ont alarm-profile 1 2 profile-id 1

Confirm that the ONT goes online normally.

After an ONT is added, run the

display ont info

command to query the current status

of the ONT. Ensure that

Control flag

of the ONT is

active

Run State

online

Config state

normal

, and

Match state

match

huawei(config-if-gpon-0/1)#

display ont info 1 1

---------------------------------------------------------------------

F/S/P

0/1/1

ONT-ID

Control flag

active

//Indicates that the ONT is

activated.

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

135

Page 144 / 429

Run state

online

//Indicates that the ONT goes online

normally.

Config state

normal

//Indicates that the configuration status

of the

ONT is normal.

Match state

match

//Indicates that the capability profile

bound to

the ONT is consistent with the

actual capability

of the ONT.

...//The rest of the response information is omitted.

If the ONT state fails, the ONT fails to be in the up state, or the ONT does not match,

check the ONT state by referring to the above-mentioned descriptions.

–

Control flag

deactive

, run the

ont activate

command in the GPON port mode

to activate the ONT.

–

If the ONT fails to be in the up state, that is,

Run state

offline

, the physical line

may be broken or the optical transceiver may be damaged. You need to check both

the material and the line.

–

If the ONT state fails, that is,

Config state

failed

, the ONT capability set

outmatches the actual ONT capabilities (For details about the ONT actual

capabilities, see Reference of GPON ONT Capability Sets). In this case, run the

display ont failed-configuration

command in the diagnosis mode to check the

failed configuration item and the failure cause. Then, rectify the fault according to

actual conditions.

NOTE

If an ONT supports only four queues, the values of 4–7 of the priority-queue parameter in the

gem add

command are invalid. After configuration recovers, Config state will be failed.

–

If the ONT does not match, that is,

Match state

mismatch

, the port types and

number of ports undermatch the actual port types and number of ports supported

by the ONT. In this case, run the

display ont capability

command to query the

actual capability of the ONT, and then select one of the following modes to modify

the ONT configuration:

–

Create a proper ONT profile according to the actual capability of the ONT, and

then run the

ont modify

command to modify the configuration data of the ONT.

–

Modify the ONT profile according to the actual capability of the ONT and save

the modification. Then, the ONT automatically recovers the configuration

successfully.

Specify the native VLAN for the ONT port.

ETH port 1 on the ONT is connected to the PC and the native VLAN is VLAN 10.

huawei(config-if-gpon-0/1)#

ont port native-vlan 1 1 eth 1 vlan 10

huawei(config-if-gpon-0/1)#

ont port native-vlan 1 2 eth 1 vlan 10

Configure a traffic profile.

You can run the

display traffic table ip

command to query the traffic profiles existing

in the system. If the traffic profiles existing in the system do not meet the requirements,

you need to run the

traffic table ip

command to add a traffic profile.

The profile ID is 8, the CIR is 4 Mbit/s, the priority is 1, and packets are scheduled

according to the priority carried.

huawei(config-if-gpon-0/1)#

quit

huawei(config)#

traffic table ip index 8 cir 4096 priority 1 priority-

policy tag-In-Package

Create service ports.

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

136

Page 145 / 429

Set the service port indexes to 1 and 2, SVLAN ID to 100, GEM port ID to 1, and

CVLAN ID to 10. Use traffic profile 8.

huawei(config)#

service-port 1 vlan 100 gpon 0/1/1 ont 1 gemport 1 multi-

service user-vlan 10 rx-cttr 8 tx-cttr 8

huawei(config)#

service-port 2 vlan 100 gpon 0/1/1 ont 2 gemport 1 multi-

service user-vlan 10 rx-cttr 8 tx-cttr 8

Configure the queue scheduling mode.

Use the 3PQ+5WRR queue scheduling. Queues 0-4 adopt the WRR mode, with the

weights of 10, 10, 20, 20, and 40 respectively; queues 5-7 adopt the PQ mode.

NOTE

Queue scheduling is a global configuration. You need to configure queue scheduling only once on

the OLT, and then the configuration takes effect globally. In the subsequent phases, you do not need

to configure queue scheduling repeatedly when configuring other services.

huawei(config)#

queue-scheduler wrr 10 10 20 20 40 0 0 0

Configure the mapping between queues and 802.1p priorities. Priorities 0-7 map

queues 0-7 respectively.

huawei(config)#

cos-queue-map cos0 0 cos1 1 cos2 2 cos3 3 cos4 4 cos5 5 cos6

6 cos7 7

For the service board that supports only four queues, the mapping between 802.1p

priorities and queue IDs is as follows: priorities 0 and 1 map queue 1; priorities 2 and

3 map queue 2; priorities 4 and 5 map queue 3; priorities 6 and 7 map queue 4.

10.

Save the data.

huawei(config)#

save

Configure the ONT.

The ONT is connected to the upper-layer device in Layer 2 mode. Users perform PPPoE

dialup on their PCs and no configuration is required on the ONT.

----End

Result

After physical port LAN1 on the ONT is connected to a PC, perform PPPoE dialup using

software on the PC. After successful PPPoE dialup, the user can access the Internet following

entering correct network addresses.

Configuration File

vlan 100 smart

vlan attrib 100 stacking

port vlan 100 0/19 0

dba-profile add profile-id 10 type4 max 102400

ont-lineprofile gpon profile-id 10

tcont 4 dba-profile-id 10

gem add 1 eth tcont 4

mapping-mode vlan

gem mapping 1 0 vlan 10

commit

quit

ont-srvprofile gpon profile-id 10

ont-port eth 4 pots 2 catv 1

port vlan eth 1 10

commit

quit

interface gpon 0/1

port 1 ont-auto-find enable

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

137

Rate

Popular Huawei Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share