Huawei HG8245T Router Manual PDF (Setup & Configuration Guide)

Page 151 / 429 Scroll up to view Page 146 - 150

by the ONT. In this case, run the

display ont capability

command to query the

actual capability of the ONT, and then select one of the following modes to modify

the ONT configuration:

–

Create a proper ONT profile according to the actual capability of the ONT, and

then run the

ont modify

command to modify the configuration data of the ONT.

–

Modify the ONT profile according to the actual capability of the ONT and save

the modification. Then, the ONT automatically recovers the configuration

successfully.

6.

Configure a traffic profile.

You can run the

display traffic table ip

command to query the traffic profiles existing

in the system. If the traffic profiles existing in the system do not meet the requirements,

you need to run the

traffic table ip

command to add a traffic profile.

The profile ID is 8, the CIR is 4 Mbit/s, the priority is 1, and packets are scheduled

according to the priority carried.

huawei(config-if-gpon-0/1)#

quit

huawei(config)#

traffic table ip index 8 cir 4096 priority 1 priority-

policy tag-In-Package

7.

Create service ports.

Set the service port indexes to 1 and 2, SVLAN ID to 100, GEM port ID to 1, and

CVLAN ID to 10. Use traffic profile 8.

huawei(config)#

service-port 1 vlan 100 gpon 0/1/1 ont 1 gemport 1 multi-

service user-vlan 10 rx-cttr 8 tx-cttr 8

huawei(config)#

service-port 2 vlan 100 gpon 0/1/1 ont 2 gemport 1 multi-

service user-vlan 10 rx-cttr 8 tx-cttr 8

8.

Configure the queue scheduling mode.

Use the 3PQ+5WRR queue scheduling. Queues 0-4 adopt the WRR mode, with the

weights of 10, 10, 20, 20, and 40 respectively; queues 5-7 adopt the PQ mode.

NOTE

Queue scheduling is a global configuration. You need to configure queue scheduling only once on

the OLT, and then the configuration takes effect globally. In the subsequent phases, you need not

configure queue scheduling repeatedly when configuring other services.

huawei(config)#

queue-scheduler wrr 10 10 20 20 40 0 0 0

Configure the mapping between queues and 802.1p priorities. Priorities 0-7 map

queues 0-7 respectively.

huawei(config)#

cos-queue-map cos0 0 cos1 1 cos2 2 cos3 3 cos4 4 cos5 5 cos6

6 cos7 7

For the service board that supports only four queues, the mapping between 802.1p

priorities and queue IDs is as follows: priorities 0 and 1 map queue 1; priorities 2 and

3 map queue 2; priorities 4 and 5 map queue 3; priorities 6 and 7 map queue 4.

9.

Save the data.

huawei(config)#

save

l

Configure the optical network terminal (ONT) on the Web page.

Layer 3 route mode is used for connecting an ONT to the upper-layer device. IP addresses

of users' PCs are allocated by the DHCP IP address pool on the ONT. PPPoE auto dialup

is performed on the ONT. Parameters of the WAN port must be configured on the ONT.

1.

Log in to the Web configuration window.

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

143

Page 152 / 429

(1)

Configure the IP address of the PC network adapter to be in the same network

segment as the IP address of the local maintenance Ethernet port of the ONT

(default:

192.168.100.1

).

(2)

Open the Web browser, and enter the IP address of the local maintenance Ethernet

port of the ONT.

(3)

On the login window, enter the user name (default:

telecomadmin

) and password

(default:

admintelecom

) of the administrator. After the password authentication

is passed, the Web configuration window is displayed.

2.

Configure the working mode of a LAN port.

(1)

In the navigation tree, choose

LAN

>

LAN Port Work Mode

. Select the check

box of LAN 1 and set LAN1 to work in the Layer 3 mode.

(2)

Click

Apply

to apply the configuration.

3.

Configure parameters of a WAN port.

(1)

In the navigation tree, choose

WAN

>

WAN Configuration

.

(2)

In the right pane, click

New

. In the dialog box that is displayed, configure

parameters of a WAN port as follows:

–

WAN Connection: Enable

–

Service List: INTERNET (For configuring the Internet access service,

INTERNET

or a combination containing

INTERNET

needs to be selected.)

–

Mode: Route

–

VLAN ID: 10 (The VLAN ID of the ONT must be the same as the user-side

VLAN ID configured on the OLT.)

–

802.1p: 1

–

IP Acquisition Mode: PPPoE

–

NAT: Enable (NAT must be enabled to configure the Internet access service.)

–

User Name: iadtest@pppoe, Password: iadtest (The user name and password

must be the same as the user name and password configured on the BRAS.)

–

Binding options: LAN1

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

144

Page 153 / 429

(3)

Click

Apply

to apply the configuration.

4.

Save the configuration.

In the navigation tree, choose

System Tools

>

Configuration File

. In the right pane,

click

Save Configuration

to save the configuration.

5.

Check the ONT connection status.

In the navigation tree, choose

Status

>

WAN Information

. In the right pane,

Status

is

Connected

and the obtained IP address is displayed at

IP

.

l

Configure the ONT on the U2000.

Layer 3 route mode is used for connecting the ONT to the upper-layer device. IP addresses

of users' PCs are allocated by the DHCP IP address pool on the ONT. PPPoE auto dialup

is performed on the ONT. Parameters of the WAN port must be configured on the ONT.

The following uses batch configurations of creating a value-added service profile of the

ONT as an example. To configure an ONT, on the GPON ONU tab page, select an ONT,

right-click, and choose

Configure Value-Added Service

from the shortcut menu.

1.

Log in to the NMS (iManager U2000 V100R003C00) and start the FTP service.

2.

Configure the value-added service profile of the ONT.

(1)

From the main menu, choose

Configuration

>

Access Profile Management

. In

the navigation tree of the tab page that is displayed, choose

PON Profile

>

ONT

VAS Profile

.

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

145

Page 154 / 429

(2)

On the

ONT VAS Profile

tab page, right-click, and choose

Add

from the shortcut

menu.

(3)

In the dialog box that is displayed, set relevant parameters.

–

Profile Name: ONT-HSI

–

Vendor ID: HWTC(2011)

–

Terminal Type: 247

–

Version: V1R003C00-Later

(4)

Configure the working mode of a LAN port.

In the navigation tree, choose

LANDevice

>

LAN Interface 1

>

LAN

Interface

>

LAN Ethernet Configuration 1

. Select

LAN Ethernet

Configuration 1

and set

LAN port two three-port enable

to

enable

(indicating

that LAN 1 works in the Layer 3 mode).

NOTE

l

If

LAN port two three-port enable

is

disable

, the LAN port works in the Layer 2

mode.

l

If

LAN port two three-port enable

is

enable

, the LAN port works in the Layer 3

mode.

LAN port two three-port enable

is defaulted to

disable

.

By default, the system has one

LAN Ethernet Configuration 1

node. To add nodes,

select

LAN Interface

, right-click, and choose

Add

from the shortcut menu.

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

146

Page 155 / 429

(5)

Configure parameters of a WAN port.

a.

In the navigation tree, choose

WAN Device

>

WAN Device 1

>

WAN

Connection

. Select

WAN Connection

, right-click, and choose

Add PPP

Connection

from the shortcut menu.

b.

Select

WAN PPP Interface 1

and enter (or select) a proper value.

–

WAN Interface Name: ONT-HSI

–

WAN Enable: enable

–

Connection Type: IP_Routed

–

NATEnable: Enable (NAT must be enabled to configure the Internet

access service.)

–

Service Type: INTERNET (For configuring the Internet access service,

INTERNET

or a combination containing

INTERNET

needs to be

selected.)

–

VLAN ID: 10 (The VLAN ID of the ONT must be the same as the user-

side VLAN ID configured on the OLT.)

–

Priority: 1

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

147

Rate

Popular Huawei Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share