Page 56 / 96
Scroll up to view Page 51 - 55
´µ
D-Link DWL-7100AP User Manual
Wireless Settings
SSID Broadcast:
The Service Set (network) Identifier of your
wireless network.
Allows you to select a channel. 6 is the default
setting.
Allows you to enable or disable the broadcasting
of the SSID to network clients.
Disabled by default. You can select
Super A/G
without Turbo
or
Super A/G with Dynamic
Turbo
.
Select
Disable
or
Enable
from the drop-down
menu.
Select
Disable
or
Enable
from the drop-down
menu.
Select
Short and Long
(default) or
Long Only
.
A drop-down menu to select the maximum wireless
signal rate for the selected devices(s).
Beacons are packets sent by an access point to
synchronize a network. Specify the beacon value
for the selected device(s) here. The default value
of 100 is recommended.
SSID:
Channel:
Super A/Super G:
Wireless QoS (WMM):
Radio Wave:
Data Rate:
Preamble:
Beacon Interval
(20~1000):
Page 57 / 96
´7
D-Link DWL-7100AP User Manual
DTIM (1~255)
:
This sets the fragmentation threshold (specified in bytes). Packets exceeding the value set here will be fragmented. The default
is 2346.
Fragment Length
(256~2346):
The RTS value should not be changed unless you encounter inconsistent data flow. The default value is 2346.
DTIM (Delivery Traffic Indication Message) is a countdown informing clients of the next listening window for broadcast
and multicast messages.
RTS Length:
Enable this option to allow the access point to automatically scan for an available channel.
A drop-down menu for selecting the transmit power of the selected device(s).
Tx Power:
Auto Channel Scan:
Page 58 / 96
´¶
D-Link DWL-7100AP User Manual
Security
The Security tab contains the WEP configuration settings on the intial page. If you select WPA as the authentication type, an additional
tab will appear with the WPA configuration options based on your selection.
The key is communicated across the network.
Open:
Shared:
Open System/
Shared Key:
WPA:
WPA-PSK:
Limited to communication with devices that share
the same WEP settings.
The key is communicated and identical WEP
settings are required.
Used to authenticate clients via a RADIUS
server.
Does not utilize a RADIUS server for authentication
but uses a passphrase that is configured on the
clients and access points.
Authentication
Type:
Select from the drop-down menu the type
of authentication to be used on the selected
device(s).
Key Values:
Select which defined key is active on the selected
device(s).
Select the key size (64-bit, 128-bit, or 152-bit) and
key type (HEX or ASCII) and then enter a string
to use as the key. The key length is automatically
adjusted based on the settings you choose.
Encryption:
Enable or disable encryption on the selected
device(s).
Page 59 / 96
´·
D-Link DWL-7100AP User Manual
WEP Encryption
Active Key Index:
Key Values:
Open:
Shared:
Open System/
Shared Key:
Authentication
Type:
Select from the drop-down menu the type
of authentication to be used on the selected
device(s).
The key is communicated across the network.
Limited to communication with devices that share
the same WEP settings.
The key is communicated and identical WEP
settings are required.
Select which defined key is active on the selected
device(s).
Select the key size (64-bit, 128-bit, or 152-bit) and
key type (HEX or ASCII) and then enter a string
to use as the key. The key length is automatically
adjusted based on the settings you choose.
Page 60 / 96
µ0
D-Link DWL-7100AP User Manual
WPA-EAP/WPA2-EAP/ WPA-Auto-EAP
Cipher Type:
Select
Auto, TKIP
, or
AES
from the drop-down
menu.
Select the interval during which the group key will
be valid. 1800 is the recommended setting. A lower
interval may reduce transfer rates.
Enter the IP address of the RADIUS server.
Enter the port used on the RADIUS server (1812
is default).
Enter the RADIUS secret.
Group Key Update
Interval:
RADIUS Server:
RADIUS Port:
RADIUS Secret:
19216811.live