Page 31 / 91
Scroll up to view Page 26 - 30
DG-HR1400 User Manual
31
3-3 Using Quick Setup
This router provides a ‘Quick Setup’ procedure, which will help you to complete all
required settings you need to access the Internet in very short time. Please follow the
instructions mentioned below to complete the ‘
Quick Setup
’:
Please go to Quick Setup menu by clicking ‘
Setup
’ button.
And the following message will be displayed:
Click the “
Next
” button to continue.
Please follow the steps and complete the router configuration.
Page 32 / 91
DG-HR1400 User Manual
32
Step 1 Setup WAN Connection Type:
Below given ‘
WAN Connection Type
’ screen will appear.
Please choose the broadband (Internet connection) type you’re using in this page.
There are three types of Internet connection: PPPoE, Dynamic IP and Static IP.
If you’re not sure, please contact your Internet service provider. A wrong Internet
connection type will cause connection problem, and you will not be able to connect
to the internet.
If you want to go back to previous step, please press ‘
Back
’ button.
NOTE:
Some
service
providers
use
‘DHCP’
(Dynamic
Host
Configuration Protocol) to assign IP address to your router. In
this case, you can choose ‘Dynamic IP’ as Internet connection
type.
Page 33 / 91
DG-HR1400 User Manual
33
Setup procedure for ‘PPPoE’:
Choose PPPoE. (Point to Point Protocol over Ethernet) If your ISP uses a PPPoE
connection it will provide you with a username and password. This option is typically
used for DSL services. Below given screen will be displayed.
Here is the description of every setup item:
Parameter
Description
User Name
Please input user name assigned by your Internet service
provider here.
Password
Please input the password assigned by your Internet service
provider here.
Confirm
Password
Re-enter the password in this field for confirmation.
When you finish with all settings, press ‘
Next
’; if you want to go back to previous
menu, click ‘
Back
’.
Setup procedure for ‘Dynamic IP’:
Select Dynamic IP to obtain IP Address information automatically from your ISP.
Usually Cable Modem and the router will automatically obtain an IP address from the
DHCP server.
Page 34 / 91
DG-HR1400 User Manual
34
Setup procedure for ‘Static IP’:
Select Static IP Address if IP information is provided to you by your ISP. You will
need to enter in the IP address, subnet mask, gateway address and DNS address
provided to you by your ISP. Each IP address entered in the fields must be in the
appropriate IP form, which are four octets separated by a dot (x.x.x.x). The Router
will not accept the IP address if it is not in this format. Below given screen will be
displayed.
Here is the description of every setup item:
Parameter
Description
IP address
Please input the IP address assigned by your service provider.
Subnet Mask
Please input the subnet mask assigned by your service provider
Default Gateway
Please input the default gateway assigned by your service
provider.
Primary DNS
Please input the DNS IP address in dotted-decimal notation
provided by your ISP.
Secondary DNS
Please input another DNS IP address in dotted-decimal notation
provided by your ISP.
When you finish with all settings, press ‘
Next
’; if you want to go back to previous
menu, click ‘
Back
’.
NOTE: You must use the addresses provided by your Internet service
provider, wrong setting value will cause connection problem.
Page 35 / 91
DG-HR1400 User Manual
35
Step 2 Setup Wireless:
Below given ‘
Wireless
’ screen will appear.
Here is the description of every setup item:
Parameter
Description
Disable the wireless
radio
The wireless radio of this Router can be enabled or disabled
to allow wireless stations access.
SSID
This is the name of wireless network. Input the SSID name
that your wireless ISP has provided you with.
Channel
This is the radio frequency used to transmit and receive the
wireless signal. The wireless devices in the same network
should follow the same setting. Select the channel here.
Mode
Select the desired mode. The default setting is 2.4GHz
(B+G+N).
Channel Width
Select any channel width from the pull-down list. The
default setting is Auto 20/40M, which can adjust the channel
19216811.live