3 - Installing and configuring the residential gateway

SAGEM F@st™ 3202 Reference Manual - 288060387-01

Page 3-4

Reproduction and communication prohibited without the written permission of

E

4

The screen opposite appears.

Click the

button to

install your Residential Gateway on the

USB

interface.

5

The screen opposite appears and

prompts you to wait.

6

The screen opposite appears.

Now connect the USB cable by

connecting the "square" type B end to

the Residential Gateway (

USB PC

socket) then by connecting the other

"flat" type A end to an available

corresponding socket on your computer

as shown in the animation on screen.

3 - Installing and configuring the residential gateway

SAGEM F@st™ 3202 Reference Manual - 288060387-01

Reproduction and communication prohibited without the written permission of

E

Page 3-5

7

The next screen appears.

Enter the login identifier followed by the

login password.

These can be found in your

subscription confirmation email.

Click the

button to

continue installation.

8

The screen opposite appears and

prompts you to wait.

9

After a relatively short time, the screen

opposite appears.

Installation is finished.

Click

.

3 - Installing and configuring the residential gateway

SAGEM F@st™ 3202 Reference Manual - 288060387-01

Page 3-6

Reproduction and communication prohibited without the written permission of

E

Accessing your Residential Gateway's HTTP configurator

1

Double click the configuration icon

on the desktop, the Web

browser opens and the screen

prompting you to log in appears.

In the "User name" field, enter:

admin

In the "Password" field, enter:

admin

.

Click

OK

to confirm.

Note:

The bar at the top of the screen

shows the equipment's IP address.

2

Your computer's Web browser displays

the SAGEM F@st

TM

3202 home screen

via the default IP address specific to the

USB interface:

The name of the equipment is

displayed in the home screen title:

live

b

o

x



.

You can now:

¾

Access the HTTP configurator (see section 5)

,

¾

Surf the Internet,

¾

Use the Internet to make phone calls if you have taken out a

subscription to the ADSL telephony service with your Internet service

provider (ISP).

Caution:

If, on installation, you entered an

incorrect

login identifier and

password, you could have continued and finished installation and

obtained access to the HTTP configurator.

However, you will not under any circumstances be able to surf

the Internet.

To surf the Internet, you must enter the correct information sent

to you by your Internet service provider. For this:

In the HTTP configurator's home page, select

Basic

followed by

the

Internet access

menu.

3 - Installing and configuring the residential gateway

SAGEM F@st™ 3202 Reference Manual - 288060387-01

Reproduction and communication prohibited without the written permission of

E

Page 3-7

3.1.1.2

In Mac

No installation

available with the USB interface.

Installation with the Ethernet interface is described in section 3.2.1.2).

3 - Installing and configuring the residential gateway

SAGEM F@st™ 3202 Reference Manual - 288060387-01

Page 3-8

Reproduction and communication prohibited without the written permission of

E

3.2

Installing and configuring your Residential Gateway on your

computer's network card (Ethernet)

Only the

ETH1

Ethernet socket identified by

on the SAGEM F@st™ 3202 is provided

for connecting your computers or wired Ethernet equipment. This port is an Ethernet

10/100BASE-T port, which supports bit rates of 10 Mbit/s and 100 Mbit/s in half or full duplex

mode on a category 5 double twisted pair.

This port is an RJ45 connector with auto-detecting MDI or MDI-x type wiring.

On this port, you can connect using a lead (not supplied with the equipment):

•

either direct to a computer with an Ethernet 10/100BASE-T network card installed,

•

or to an Ethernet LAN connected to a network concentrator (HUB or Switch).

3.2.1

Configuring network parameters

3.2.1.1

In Windows XP

The

installation

procedure described was performed in

Windows



XP

.

Installation in other Windows



operating systems (98, ME and 2000) may

differ slightly.

1

Insert the CD-ROM in your computer's

appropriate drive; the screen opposite

appears.

Proceed as described on screen.

Click the

button to

continue installation.

Note:

If this screen does not appear: Select

Start

, then

Run

, then enter:

"<CD-ROM drive letter> :\

autorun.exe

(for example e:\autorun.exe)

then click

OK

.