Page 196 / 300 Scroll up to view Page 191 - 195
Chapter 25 Access Control
P-663HN-51 User’s Guide
196
Note: The “support” user name and password for ISP technician login only works
through the DSL connection.
Figure 100
Management > Access Control > Passwords
The following table describes the labels in this screen.
Table 72
Management > Access Control > Passwords
LABEL
DESCRIPTION
Username
Select the user name for which you want to configure the password.
The
admin
or
user
account can only access the ZyXEL Device from the
LAN.
The
support
account can only access the ZyXEL Device from the WAN.
Only the
admin
or
support
account can use Telnet to log into the ZyXEL
Device.
Old Password
Type the existing password.
New Password
Type the new password. Note that as you type a password, the screen
displays a (*) for each character you type. After you change the
password, use the new password to access the ZyXEL Device.
Confirm
Password
Type the new password again to make sure it is entered properly.
Save/Apply
Click this button to save the changes and have the ZyXEL Device start
using them.
Page 197 / 300
Chapter 25 Access Control
P-663HN-51 User’s Guide
197
25.6
Authentication
Click
Management > Access Control
>
Authentication
to open the following
screen. Use this screen to set whether or not users must enter a user name and
password to access the ZyXEL Device’s system information summary page.
Figure 101
Management > Access Control > Authentication
The following table describes the labels in this screen.
Table 73
Management > Access Control > Authentication
LABEL
DESCRIPTION
Login
authentication
on web home
page
Select this to require users to enter the ZyXEL Device’s user account’s
user name and password in order to access the ZyXEL Device’s system
information summary page.
Clear this to allow users to access the ZyXEL Device’s system information
summary page without entering the ZyXEL Device’s user account’s user
name and password.
Save/Apply
Click this button to save the changes and have the ZyXEL Device start
using them.
Page 198 / 300
Chapter 25 Access Control
P-663HN-51 User’s Guide
198
Page 199 / 300
P-663HN-51 User’s Guide
199
C
HAPTER
26
Update Software
This chapter covers upgrading the ZyXEL Device’s firmware.
26.1
Uploading Firmware
The software embedded in the ZyXEL Device is called “firmware”. Find firmware at
www.zyxel.com in a file that (usually) uses the system model name with a .bin
extension, for example, "ZyXEL Device.bin". The upload process described here
may take up to two minutes. After a successful upload, the system will reboot.
Only use firmware for your device’s specific model. Refer to the
label on the bottom of your device.
Click
Management > Update Software
to open the following screen. Follow the
instructions in this screen to upload firmware to your ZyXEL Device.
Figure 102
Management > Update Software
Page 200 / 300
Chapter 26 Update Software
P-663HN-51 User’s Guide
200
The following table describes the labels in this screen.
Do NOT turn off the ZyXEL Device while firmware upload is in
progress!
After you upload firmware, wait before logging into the ZyXEL Device again. The
ZyXEL Device automatically restarts causing a temporary network disconnect. In
some operating systems, you may see the following icon on your desktop.
Figure 103
Network Temporarily Disconnected
After the ZyXEL Device finishes restarting, log in again and check your new
firmware version in the
Status
screen.
Table 74
Management > Update Software
LABEL
DESCRIPTION
Software File
name
Type in the location of the file you want to upload in this field or click
Browse ...
to find it.
Browse...
Click
Browse...
to find the .bin file you want to upload. Remember that
you must decompress compressed (.zip) files before you can upload
them.
Update
Software
Click
Upload
to begin the upload process. This process may take up to
two minutes.

Rate

4 / 5 based on 1 vote.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top