Page 21 / 127 Scroll up to view Page 16 - 20
Chapter 3 Basic Setup
Figure 3-7 CONFIGURE WIRELESS NETWORK Page
8.
Configure the wireless network parameters.
For a description of the wireless network parameters, refer to
Table 3-3
.
Table 3-3 Wireless Network Parameter Descriptions
Parameter
Description
Enable Your Wireless
Network
The wireless network is enabled by default. You can clear the
check box to disable it and click
Next
to skip the configuration
of the wireless network.
Wireless Network Name
(SSID)
For security purpose, it is recommended to change the
pre-configured network name.
Visibility Status
If
Visibility Status
is set to
Visible
, the SSID of the wireless
network can be found by wireless clients. If
Visibility Status
is
Invisible
, the wireless network is hidden and users need to
manually enter the SSID in order to connect to the wireless
network.
3-7
SJ-20121120142951-001|2012-11-30 (R1.0)
ZTE Proprietary and Confidential
Page 22 / 127
ZXHN H108N Maintenance Management Manual
Parameter
Description
Security Level
l
None
No security level is enabled.
l
WEP
Wireless adapters only support WEP and do not support
WPA.
l
WPA-PSK
Wireless adapters support WPA-PSK.
l
WPA2-PSK
Wireless adapters support WPA2-PSK.
WEP Key/WPA Pre-Shared
Key/WPA2 Pre-Shared Key
The key should be the same as that on the wireless client for
proper wireless connections.
9.
Click
Next
. The
STEP4: COMPLETED AND RESTART
page is displayed, see
Figure
3-8
.
Figure 3-8 COMPLETED AND RESTART Page
10. Click
Apply
.
– End of Steps –
3-8
SJ-20121120142951-001|2012-11-30 (R1.0)
ZTE Proprietary and Confidential
Page 23 / 127
Chapter 3 Basic Setup
3.2 Configuring the Internet Parameters
You can configure an Asynchronous Transfer Mode (
ATM
)
PVC
identifier (VPI/VCI) and
select a service category.
Steps
1.
Select
Setup > Internet Setup
. The
INTERNET SETUP
page is displayed, see
Figure
3-9
.
Figure 3-9 INTERNET SETUP Page
2.
Click
Add
.
The configuration page for a new Internet connection is displayed, see
Figure 3-10
.
Figure 3-10 INTERNET SETUP Page–New Internet Connection Configuration
3-9
SJ-20121120142951-001|2012-11-30 (R1.0)
ZTE Proprietary and Confidential
Page 24 / 127
ZXHN H108N Maintenance Management Manual
3.
In the
ATM PVC CONFIGURATION
area, configure the parameters. For a description
of the parameters, refer to
Table 3-4
.
Table 3-4 Parameter Descriptions for ATM PVC Configuration
Parameter
Description
VPI
Virtual path identifier
VCI
Virtual channel identifier, 16 bits, indicating a virtual channel in a virtual
path
A VPI and a VCI are used together to indicate a virtual connection.
Service Category
Service type in the ATM
QoS configuration for uplink traffic control. Five service types are
supported:
l
UBR Without PCR
l
UBR With PCR
l
CBR
l
Non Realtime VBR
l
Realtime VBR
Peak Cell Rate
QoS threshold value
Sustainable Cell Rate
Sustainable cell rate
Maximum Burst Size
Maximum burst size
4.
Configure the connection type parameters.
The ZXHN H108N supports five types of protocols.
l
PPP over ATM (
PPPoA
)
i.
From the
Protocol
list, select
PPP over ATM (PPPoA)
. Configure the
connection type parameters of the PPPoA protocol.
Figure 3-11 CONNECTION TYPE Area–PPPoA
For a description of the PPPoA connection type parameters, refer to
Table
3-5
.
3-10
SJ-20121120142951-001|2012-11-30 (R1.0)
ZTE Proprietary and Confidential
Page 25 / 127
Chapter 3 Basic Setup
Table 3-5 Parameter Descriptions for the PPPoA Connection Type
Parameter
Description
Protocol
Connection protocol
Encapsulation Mode
Encapsulation type of IP packets:
°
VCMUX
°
LLC
Firewall Enable
Whether to enable the firewall
ii.
Configure the PPP parameters of the PPPoA protocol.
Figure 3-12 PPP USERNAME AND PASSWORD Area–PPPoA
For a description of the PPP parameters, refer to
Table 3-6
.
Table 3-6 PPP Parameter Descriptions
Parameter
Description
PPP Username
PPPoE/PPPoA user name, which is provided by the ISP.
PPP Password/Con-
firm PPP Password
PPPoE/PPPoA user password, which is provided by the ISP.
Authentication Method
Authentication method, including AUTO,
PAP
,
CHAP
, and
MS-CHAP. By default, it is AUTO.
3-11
SJ-20121120142951-001|2012-11-30 (R1.0)
ZTE Proprietary and Confidential

Rate

3.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top