Page 16 / 47
Scroll up to view Page 11 - 15
16
3 Voice
3.1 Making a Call
Before making a call, make sure:
The USIM card is installed.
The telephone cable (RJ11) is connected properly.
The PWR and RSSI lights are on.
Pick up the handset.
1. Key in the telephone number.
2. You should wait 4~8 seconds for the call to be connected
automatically.
Note
: If there is no RSSI indication, the RF signal is unavailable.
Change the location of the router and make sure nothing is blocking it.
3.1.1 Making a Call
If you are making a call, add the area code as normal.
E.g. 03 9612 3456
3.1.2 Making an International Call
If you are making an international call, key in the international access
code followed by the country code, area code and number.
E.g. 00 11 64 12 345678
3.2 Answering a Call
When the phone rings, pick up the handset to answer or press the
Hands-free
button (if available). Press the
Hands-free
button again to
end the call.
When answering a
Call Waiting
, press the Flash button (if available)
or press the phone’s cradle.
Page 17 / 47
17
4 Internet Access
The router does not require any drivers, and it supports all operating
systems with Ethernet LAN capability, such as Windows 2000, XP,
Vista , MAC OS X and Linux. The router supports two computers
surfing on internet using Ethernet cable at the same time, and also
supports Wireless LAN connection.
Note:
All the parameter settings in this chapter are just for your
reference. Please contact your service provider for details.
Do not change any configuration or settings without explicit
instructions from your service provider.
4.1 Preparation
Before using the data service, make sure:
The USIM card is installed.
The Ethernet cable is connected properly.
The PWR light is on.
The RSSI light is on.
The PPP light is on.
Web browser requirement:
It is suggested that you use one of these web browsers to connect to
the internet.
IE 6.0 or above
Firefox 2.0
Netscape version 9.0
Page 18 / 47
18
4.2 Settings
Do not change any settings unless instructed by your service provider.
To make changes to your settings you need to disconnect the router
from the network. After making changes reboot your router by turn off
and on again.
4.2.1 Login
The router can be connected by RJ45 or by Wi-Fi (the SSID is
“Cellcom Router”
). By either connection mode, you should set to obtain
an IP address automatically in the attribution setting
of Internet
protocol(TCP/IP).
After your computer gets the IP address (like
192.168.0.101) from the
router, open a web browser and type
“
.1” in the
address bar, and then input the username and password.
User name:
admin
Passwor
d: admin
Note
: some screens may be different from those shown here.
Click
Login
to log in the router.
Note
: If you check
Save
after you give user name and password ,the
router will save them, next time when you want to log in the router with
Page 19 / 47
19
the same user name and password, what you need to do is click
Login
.
When you successfully login, the following screen appears:
The whole interface is divided into two parts. Related functions can be
executed by operation in the related areas.
Index area:
Show configuration list for your router.
Content area:
Show the detail configuration.
4.2.2 Quick Setup
Step1.
Read the guide carefully, and then click
Next
.
Page 20 / 47
20
Step2.
Set
PPP Profile Configuration
in the following figure:
Set
APN
for PPP profile, if you obtain a fixed APN from your service
provider, please select
Manual APN
, otherwise select
Auto APN,
and
then type the APN string.
Dial No.
is provided by your service provider.
Step3.
Set the
PPP Authentication
in the following figure:
Choose PPP authentication mode CHAP or PAP, and then give PPP
user name and password to the corresponding authentication mode.
19216811.live