1. Home
    2. /
  2. Manuals
    3. /
  3. ZTE
    4. /
  4. MF612
    5. /
  5. 3
Page 11 / 47 Scroll up to view Page 6 - 10
11
LED Indicators
Indicator
State
Description
1. PWR
ON
External power supply works
normally.
OFF
External power supply is
disconnected or power off.
2. Wi-Fi
ON
Wi-Fi works normally.
Blinking
Data transmission.
OFF
Wi-Fi works abnormally, or is
disconnected.
3. PPP
ON
Internet connected.
Blinking
The router attempts to connect
Internet.
OFF
Internet disconnected and not
attempt to connect.
4. RSSI
ON
RF signal is normal. Different
color indicates different
network.
Red: GSM/GPRS/EDGE.
Green: HSDPA/HSUPA/UMTS.
Blinking
RF signal is poor.
OFF
RF signal is not available.
Note
: The indicators (including PPP and RSSI) are all blinking in green
when:
The USIM card has not been installed.
The PIN code or PUK code is required.
The router cannot work normally.
Page 12 / 47
12
2.2.2 Power Switch
Turn the router
On
or
Off
by pressing the power switch at the rear of
the router.
Power Switch
2.3 Interface and Installation
2.3.1 Interface Description
Rear View of Router
(1)
USB
: Test and diagnostic interface for factory use only.
(2)
WPS
:WPS button is used to
start Wi-Fi Protected Setup
authentication process.
(3)
ANT
: External antenna connector. If external antenna is connected,
the internal antenna is of no effect.
(4)
PHONE
: Standard RJ11 connector for Telephone.
(5)
LAN 1~ LAN 2
: Ethernet connections to computer.
(6)
POWER Socket
: Connection to the external power supply.
(7)
POWER Switch
: Turn the router ON or OFF.
Page 13 / 47
13
2.3.2 Installation
1. Insert the USIM card into the USIM card holder from the side of the
router.
a) Pull the plastic holder out.
b) Insert the USIM card with the metal contact area facing upwards
into the holder.
c) Insert the plastic holder into the router. You can hear a click when
the USIM card locks in place.
Page 14 / 47
14
Warning:
Please power off the router and remove the external power
adapter before removing or inserting the USIM card, if not, the router
or USIM card may be damaged.
2. Connect the telephone to the
PHONE
interface using phone cable
(RJ11).
3. Connect your computer to the
LAN
interface using the Ethernet
cable (RJ45).
Note:
The router will adapt the Ethernet cable style (crossover or
straight) automatically.
4. Connect the external power adaptor to a standard power outlet.
Insert the plug into the socket at the rear of the router.
5. Turn the power switch
on to get started. Make sure that the
phone is on hook before power on.
Note:
Do not put anything on the top of router. Do not lay routers to
overlap each other when using.
6. Wait 1~2 minutes after turning the router on before you use the
service. The RSSI & PWR indicator should be lit on.
Note:
When the router is turned off, an incoming caller will hear the
prompt like
“The number you have dialed is currently unavailable.’’
If the RSSI (Radio Signal Strength Indicator) LED is blinking constantly
then try moving the router to another location. The router takes 1~2
minutes to initialize, attach to the network and obtain an IP address.
2.4 Power Supply
For normal operation connect the router to the external power supply.
Page 15 / 47
15
In case of power failure or when there is no available external power
supply, the router cannot work.
2.5 About the USIM Card
Avoid handling the USIM card unnecessarily. Hold the card by the
edges to prevent static damage. Keep the USIM card away from
electrical and magnetic appliances.
If you cannot get service, make sure
that
：
You are in an area which has network coverage.
You are using the correct USIM card.

Rate

3.5 / 5 based on 2 votes.

Popular ZTE Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top