TRENDnet TEW-452BRP Router Manual PDF (Setup & Configuration Guide)

Page 41 / 64 Scroll up to view Page 36 - 40

32

WPA/WPA2 Security

If WPA or WPA2 EAP is selected, the above screen is shown.

Please set the

length of the encryption key and the parameters for the RADIUS server.

Lifetime:

Select the Lifetime of the Encryption Key from 5 Minutes to 1 Day.

As

soon as the lifetime of the Encryption Key expires, the Encryption Key will be

renewed by the Radius server.

Encryption Key:

Select the Encryption Key Length Size ranging from 64 to 128

Bits that you would like to use.

RADIUS Server:

1.

Enter the IP address, Port used and Shared Secret by the Primary Radius

Server.

2.

Enter the IP address, Port used and Shared Secret by the Secondary Radius

Server.

WPA-PSK/WPA2-PSK Security

If WPA-PSK or WPA2-PSK is selected, please set the PSK key in the passphrase

field. The length should be 8 characters at least.

Downloaded from

www.Manualslib.com

manuals search engine

Page 42 / 64

33

Advanced

This screen enables users to configure advanced wireless functions.

Beacon Interval:

Type the beacon interval in the text box. User can specify a value

from 1 to 1000. The default beacon interval is 100.

RTS Threshold:

Type the RTS (Request-To-Send) threshold in the text box. This

value stabilizes data flow. If data flow is irregular, choose values between 256 and

2346 until data flow is normalized.

Fragmentation Threshold:

Type the fragmentation threshold in the text box. If

packet transfer error rates are high, choose values between 256 and 2346 until

packet transfer rates are minimized. (NOTE: set this fragmentation threshold value

may diminish system performance.)

DTIM Interval:

Type a DTIM (Delivery Traffic Indication Message) interval in

the text box. User can specify a value between 1 and 65535. The default value is 1.

TX Rates (Mbps):

Select one of the wireless communications transfer rates,

measured in megabytes per second, based upon the speed of wireless adapters

connected to the WLAN.

11g only mode:

If Enable is selected, only 802.11g WLAN clients are allowed to

communicate with the WLAN Router.

Antenna Transmit Power:

Adjust the power of the antenna transmission by

selecting from the drop down list: full, half (-3dB), quarter (-6dB), eighth (-9dB) or

min.

Downloaded from

www.Manualslib.com

manuals search engine

Page 43 / 64

34

Status

This selection enables users to view the status of the WLAN Router LAN, WAN

and Wireless connections, and view logs and statistics pertaining to connections

and packet transfers.

Device Information

This screen enables users to view the WLAN Router’s LAN, Wireless and WAN

configurations.

Firmware Version:

Displays the latest build of the WLAN Router firmware

interface. After updating the firmware in Tools - Firmware, check this to ensure

that the firmware was successfully updated.

LAN:

This section displays the LAN interface configuration including the MAC

address, IP Address, Subnet Mask, and DHCP Server Status. Click “DHCP Table”

to view a list of client stations currently connected to the WLAN Router LAN

interface.

Wireless:

This section displays the wireless configuration information, including

the MAC address, the Connection status, SSID, Channel and Authentication type.

WAN:

This section displays the WAN interface configuration including the MAC

address, Connection status, DHCP client status, IP address, Subnet mask, Default

gateway, and DNS.

Click

“DHCP Release”

to release all IP addresses assigned to client stations

connected to the WAN via the WLAN Router. Click

“DHCP Renew”

to reassign

IP addresses to client stations connected to the WAN.

Downloaded from

www.Manualslib.com

manuals search engine

Page 44 / 64

35

Log

This screen enables users to view a running log of Router system statistics, events,

and activities. The log displays up to 200 entries. Older entries are overwritten by

new entries. The Log screen commands are as follows:

Click “

First Page

” to view the first page of the log

Click “

Last Page

” to view the final page of the log

Click “

Clear Log

” to delete the contents of the log and begin a new log

Click “

Refresh

” to renew log statistics

Time:

Displays the time and date that the log entry was created.

Message:

Displays summary information about the log entry.

Source:

Displays the data source.

Destination:

Displays the data destination.

Note:

Displays the IP address of the communication

Downloaded from

www.Manualslib.com

manuals search engine

Page 45 / 64

36

Log Setting

This screen enables users to set Router Log parameters.

SMTP Server:

Type your SMTP server address here.

Send to:

Type an email address for the log to be sent to. Click “Email Log Now” to

immediately send the current log.

SMTP Authentication:

Selected the Enabled if the SMTP server need for

authentication, fill in account name and password in SMTP Account field and

SMTP Password field.

SMTP Account:

If the SMTP Authentication enabled, fill in the SMTP account

name here.

SMTP Password:

If the SMTP Authentication enabled, fill in the password of the

SMTP account here.

Syslog Server:

Type the IP address of the Syslog Server if user wants the WLAN

Router to listen and receive incoming Syslog messages.

Log Type:

Enables users to select what items will be included in the log:

System Activity:

Displays information related to WLAN Router operation.

Debug Information:

Displays information related to errors and system

malfunctions.

Attacks:

Displays information about any malicious activity on the network.

Dropped Packets:

Displays information about packets that have not been

transferred successfully.

Notice:

Displays important notices by the system administrator.

Downloaded from

www.Manualslib.com

manuals search engine

Rate

Popular TRENDnet Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share