Page 61 / 128
Scroll up to view Page 56 - 60
4.2.1. Port Configuration
This page can change every port status.
Press
Space
key to change configures of per item.
1. InRate (100K/unit):
User can set input rate control, per unit is 100K. The valid range is 0~1000.
0: disable rate control.
1~1000: valid rate value.
2. OutRate (100K/unit):
User can set output rate control, per unit is 100K. The valid range is 0~1000.
0: disable rate control.
1~1000: valid rate value.
3. Enabled:
User can
disable
or
enable
this port control.
“
Yes
” that mean the port is enable.
“
No
” that mean the port is disable.
4. Auto:
User can set auto negotiation mode is “
Auto
”, “
Nway_Force
”, “
Force
” of per port.
5. Spd/Dpx:
User can set “
100M
bps” or “
10M
bps” speed on port 1~port 24,
Set “
1000M
bps”, “
100M
bps” or “
10M
bps” speed on port25~port26 (depend on module card
mode), and set “
full-duplex
” or “
half-duplex
” mode.
- 61 -
Page 62 / 128
6. Flow Control:
Full:
User can set full flow control function (
pause
) as enable or disable.
Half:
User can set half flow control function (
backpressure
) as enable or disable.
NOTE:
1.
Pressing
<Save
> only can save one page configuration.
2.
If the static trunk groups exist, you can see it (ex: TRK1, TRK2…) after port 26, and you can configure all of the
items as above.
- 62 -
Page 63 / 128
4.2.2. Trunk Configuration
This page can create max seven trunk groups. User can arbitrarily select up to four ports from port
1~port 26 to build a trunk group.
Actions->
1. Select
<Edit>
on actions menu
2. Press
space
key to configure the member port of trunk group. Besides, you have to set “Static” or
“LACP” for the corresponding trunk group of TRK1~TRK7 item.
“Static” – the normal trunk.
“LACP” – this trunk group have link aggregation control protocol.
3. Press
Ctrl+A
to go back action menu line
4. Select
<Save>
to save all configure value.
5.
If the item of TRK1~TRK7 is set “Disable”, it’s mean the trunk group is deleted.
6.
All ports in the same static trunk group will be treated as single port. So when you setting VLAN
members and Port configuration they will be toggled on or off simultaneously.
NOTE:
If VLAN group exist, all of the members of static trunk group
must
be in same VLAN group
.
- 63 -
Page 64 / 128
4.2.3. VLAN Configuration
4.2.3.1. VLAN Configure
This page can set VLAN mode to port-based VLAN or 802.1Q VLAN or disable VLAN function.
- 64 -
Page 65 / 128
NOTE:
Change the VLAN mode for every time, user have to restart the switch for valid value.
If set
802.1Q VLAN
, you can set PVID, ingress filtering 1 and ingress filtering 2 in this page too.
Actions->
1. PVID (Port VID: 1~255):
Type the PVID.
2. NonMember Drop:
It matches that Ingress Filtering Rule 1 on web.
Forwarding only packets with VID matching this port’s configured VID.
Press
Space
key to choose “forward” or “drop” the frame that VID not matching this port’s
configured VID.
3. UnTagged Drop:
It matches that Ingress Filtering Rule 2 on web.
Drop untagged frame.
Press
Space
key to choose “drop” or “forward” the untagged frame.
- 65 -
19216811.live