Motorola Netopia-3000 Router Manual PDF (Setup & Configuration Guide)

Home

Manuals

Motorola

Netopia-3000

Page 211 / 351 Scroll up to view Page 206 - 210

211

Link:

ts:

DSL

The DSL port selection shows the state of the DSL line, whether it is up or down and how

many times the Gateway attempted to train. The state should indicate ‘up’ for a working

conﬁguration. If it is not, check the DSL cable and make sure it is plugged in correctly and

not connected to a micro ﬁlter. Below is an example:

ADSL Line State:

ADSL Startup Attempts:

ADSL Modulation:

DMT

Datapump Version:

3.22

Downstream

Upstream

----------

SNR Margin:

18.6

14.0 dB

Line Attenuation:

0.4

4.0 dB

Errored Seconds:

Loss of Signal:

Loss of Frame:

CRC Errors:

Data Rate:

8000

800

Page 212 / 351

212

Link:

IP:

Interfaces

The IP interfaces selection shows the state and conﬁguration information for your IP LAN

and WAN interfaces. Below is an example:

IP interfaces:

Ethernet 100BT: ( up broadcast default rip-send v1 rip-receive v1 )

inet 192.168.1.1 netmask 255.255.255.0 broadcast 192.168.1.255

physical address 00-00-00-00-00-00 mtu 1500

PPP over Ethernet vcc1: ( up address-mapping broadcast default admin-disabled

rip-send v1 rip-receive v1 )

inet 0.0.0.0 netmask 0.0.0.0 broadcast 0.0.0.0

physical address 00-00-00-00-00-00 mtu 1500

Page 213 / 351

213

Link:

DSL:

Cir

cuit Conﬁ

guration

The DSL Circuit Conﬁguration screen shows the trafﬁc sent and received over the DSL line

as well as the trained rate (upstream and downstream) and the VPI/VCI. Verify trafﬁc is

being sent over the DSL line. If not, check the cabling and make sure the Gateway is not

connected to a micro ﬁlter. Also verify the correct PVC is listed, which should be 0/35

(some providers use other values, such as 8/35. Check with your provider). If not go to the

WAN setup and change the VPI/VCI to its correct value. Below is an example:

ATM port status

: Up

Rx data rate (bps) : 8000

Tx data rate (bps) : 800

ATM Virtual Circuits:

VCC #

Type

VPI

VCI

Encapsulation

----

---

-----

--------------------------

PVC

PPP over Ethernet (LLC/SNAP encapsulation)

ATM Circuit Statistics:

Rx Frames

17092

Tx Frames

25078

Rx Octets

905876

Tx Octets

1329134

Rx Errors

Tx Errors

Rx Discards

Tx Discards

No Rx Buffers :

Tx Queue Full :

Page 214 / 351

214

Link:

System Log:

Entire

The system log shows the state of the WAN connection as well as the PPPoE session. Ver-

ify that the PPPoE session has been correctly established and there are no failures. If

there are error messages, go to the WAN conﬁguration and verify the settings. The follow-

ing is an

example

of a

successful connection

Message Log:

00:00:00:00 L3

KS: Using configured options found in flash

00:00:00:00 L3

BOOT: Warm start v7.3r0 ----------------------------------

00:00:00:00 L3

IP address server initialization complete

00:00:00:00 L4

BR: Using saved configuration options

00:00:00:00 L4

BR: Netopia SOC OS version 7.3.0 (build r0)

00:00:00:00 L4

BR: Netopia-3000/9495032 (Netopia-3000, rev 1), PID 1205

00:00:00:00 L4

BR: last install status: Firmware installed successfully

00:00:00:00 L4

BR: memory sizes - 2048K Flash, 8192K RAM

00:00:00:00 L3

BR: Starting kernel

00:00:00:00 L3

AAL5: initializing service

00:00:00:00 L4

ATM: Waiting for PHY layer to come up

00:00:00:00 L3

POE: Initializing PPP over Ethernet service

00:00:00:00 L4

POE: Binding to Ethernet (ether/vcc1)

00:00:00:00 L3

BRDG: Configuring port (10/100BT-LAN)

00:00:00:00 L3

BRDG: Bridge not enabled for WAN.

00:00:00:00 L3

BRDG: Bridging from one WAN port to another is disabled

00:00:00:00 L3

BRDG: Initialization complete

00:00:00:00 L4

IP: Routing between WAN ports is disabled

00:00:00:00 L4

IP: IPSec client pass through is enabled

00:00:00:00 L4

IP: Address mapping enabled on interface PPP over Ethernet vcc1

00:00:00:00 L3

IP: Adding default gateway over PPP over Ethernet vcc1

00:00:00:00 L3

IP: Initialization complete

00:00:00:00 L3

IPSec: initializing service

00:00:00:00 L3

IPSec: No feature key available - service disabled

00:00:00:00 L3

PPP: PPP over Ethernet vcc1 binding to PPPoE

00:00:00:00 L3

PPP: PPP over Ethernet vcc1 Port listening for incoming PPP connection requests

00:00:00:24 L4

RFC1483-1 up

00:00:00:25 L3

Service-Name=ANY

00:00:00:25 L3

Host-Uniq 00000001

00:00:00:25 L3

AC-Name=62011050058192-SMS1800

00:00:00:25 L3

Service-Name=ANY

00:00:00:25 L3

lcp: LCP Send Config-Request+

00:00:00:25 L3

MAGIC 0x2dee0000+

00:00:00:25 L3

lcp: LCP Recv Config-Req:+

00:00:00:25 L3

MRU(1492) (ACK) AUTHTYPE(c223) (CHAP) (ACK) MAGICNUMBER

00:00:00:25 L3

(4403604) (ACK)

00:00:00:25 L3

lcp: returning Configure-Ack

00:00:00:25 L3

chap: received challenge, id 1

00:00:00:25 L3

chap: received success, id 1

00:00:00:25 L3

ipcp: IPCP Config-Request+

00:00:00:25 L3

ADDR(0x0) DNS(0x0) DNS2(0x0) WINS(0x0) WINS2(0x0)

00:00:00:25 L3

ipcp: IPCP Recv Config-Req:+

00:00:00:25 L3

ADDR(143.137.199.254) (ACK)

00:00:00:25 L3

ipcp: returning Configure-ACK

00:00:00:25 L3

ipcp: IPCP Config-Request+

00:00:00:25 L3

ADDR(0x0) DNS(0x0) DNS2(0x0)

00:00:00:25 L3

ipcp: IPCP Config-Request+

00:00:00:25 L3

ADDR(0x8f89c702) DNS(0x8f89320a) DNS2(0x8f898909)

00:00:00:25 L3

ipcp: negotiated remote IP address 143.137.199.254

00:00:00:25 L3

ipcp: negotiated IP address 143.137.199.2

00:00:00:25 L3

ipcp: negotiated TCP hdr compression off

00:00:00:27 L3

NTP: Update system date & time

7/16/03 01:55:31 PM L4

TS: "admin" logging in on serial port 0

7/16/03 01:55:33 PM L4

TS: "Admin" completed login: Full Read/Write access

7/16/03 01:55:33 PM L4

TS: "Admin" completed login: Full Read/Write access

Page 215 / 351

215

Link:

Dia

gnostics

The diagnostics section tests a number of different things at the same time, including the

DSL line, the Ethernet interface and the PPPoE session.

The following table summarizes the possible results.

CODE

Description

PASS

The test was successful.

FAIL

The test was unsuccessful.

SKIPPED

The test was skipped because a test on which it depended failed, or it was not sup-

ported by the service provider equipment to which it is connected, or it does not

apply.

PENDING

The test timed out without producing a result. Try running the test again.

WARNING

The test was unsuccessful. The Service Provider equipment your Gateway connects to

may not support this test.

==== Checking LAN Interfaces

Check Ethernet LAN connect

PASS

Check IP connect to Ethernet (LAN)

PASS

Pinging Gateway

PASS

Check MAC-Bridge connect to Ethernet

(LAN)

PASS

==== Checking DSL (WAN) Interfaces

Check DSL Synchronization

PASS

Check ATM Cell-Delineation

PASS

ATM OAM Segment Ping through

(vcc1)

WARNING

*** Don't worry, your service provider may not support this test

ATM OAM End-To-End Ping through

(vcc1)

WARNING

*** Don't worry, your service provider may not support this test

Check Ethernet connect to AAL5

(vcc1)

PASS

Check PPPOE connect to Ethernet (vcc1)

PASS

Check PPP connect to PPPOE (vcc1)

PASS

Check IP connect to PPP (vcc1)

PASS

Pinging Gateway

PASS

==== Checking Miscellaneous

Check DNS- Query for netopia.com

SKIPPED

Ping DNS Server Primary IP Address

SKIPPED

TEST DONE

Rate

Popular Motorola Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share