1. Home
    2. /
  2. Manuals
    3. /
  3. Linksys
    4. /
  4. SPA-841
    5. /
  5. 22
Page 106 / 286 Scroll up to view Page 101 - 105
Administering the SPA400 and Voice Mail Service
Configuring the SPA400 Network Connection
SPA9000 Voice System Administration Guide
104
5
Configuring the SPA400 Network Connection
The SPA400 becomes a DHCP client of any server on the network. The
recommended setting is to use a static IP address. This configuration provides
ease of installation and prevents connectivity issues that would occur if the IP
address of the SPA400 changed.
STEP 1
Start Internet Explorer, and enter the IP address of the SPA400.
NOTE
By default, the SPA400 is configured to obtain an IP Address via DHCP. You
can check the obtained IP address on the router DHCP server’s client list.
STEP 2
When the password prompt appears, enter the default user name,
Admin
, with no
password. Then click OK.
NOTE
The user name must be entered exactly as shown:
Admin
. For information
about access, refer to
“Managing Access to the SPA400 Web-Based
Configuration Utility,” on page106
.
STEP 3
Click Setup tab > Basic Setup.
STEP 4
Enter the following settings:
Network Setup section:
•
Fixed IP address: Click the radio button, and then enter a valid IP address.
NOTE
To avoid addressing conflicts, enter an IP address that is outside the
range of addresses that are automatically assigned by your DHCP
server.
•
IP Subnet Mask:
Enter the subnet mask for the subnetwork that the
SPA400 is on.
•
Gateway IP Address:
Enter the IP address of the router for this subnetwork.
Downloaded from
www.Manualslib.com
manuals search engine
Page 107 / 286
Administering the SPA400 and Voice Mail Service
Saving or Discarding Changes on the SPA400
SPA9000 Voice System Administration Guide
105
5
Domain Name Server (DNS) Address section:
•
Primary DNS:
Enter the IP address of the primary DNS server.
•
Secondary DNS:
Enter the IP address of the secondary DNS server.
NTP section:
•
NTP:
Enter a fully qualified name of a Network Time Protocol server, such as
time.nist.gov.
•
Time Zone:
Select the time zone for your region.
STEP 5
Click
Save Settings
. The SPA400 will reboot. To reconnect to the web
administration server, enter the new IP address for the SPA400 in the browser
Address bar.
Saving or Discarding Changes on the SPA400
Changes can be saved or discarded at any time.
•
Changes are submitted only when you click the
Save Settings
button at the
bottom of a page.
•
To discard unsubmitted changes, click the
Cancel Changes
button at the
bottom of the page.
•
Unsubmitted changes are not retained when you move among the pages.
•
After you submit changes in the SIP or Voice mail accounts settings, reboot the
SPA400.
TIP
Before you make changes, save a copy of your current working configuration:
1.
In Internet Explorer, connect to the administration web server.
2.
Navigate to the page that has the settings that you want to save.
3.
From the menu, choose
File > Save As
.
Downloaded from
www.Manualslib.com
manuals search engine
Page 108 / 286
Administering the SPA400 and Voice Mail Service
Managing Access to the SPA400 Web-Based Configuration Utility
SPA9000 Voice System Administration Guide
106
5
4.
Save the configuration as Web Page Complete. The currently displayed page is
saved. You can use the saved file to review the settings as needed.
5.
Repeat these steps for each page, as needed.
Managing Access to the SPA400 Web-Based Configuration
Utility
One log on can be established for access to the SPA400 web-based configuration
utility. The default username of Admin can be changed, and a password can be
entered.
STEP 1
Connect to the SPA400 administration web server. (See
“Connecting to the
SPA400 Administration Web Server,” on page103
.)
STEP 2
Click
Administration
tab > Management
.
SPA400 Administration > Management
STEP 3
Proceed as needed:
•
Gateway Username:
Type the desired username in this field, up to 32
characters.
•
Gateway Password:
Type the password.
•
Retype to Confirm:
Type the password again. Both entries must match exactly.
STEP 4
Click
Save Settings
.
STEP 5
To restart the SPA400, complete the following steps:
a.
Click
Administration
tab >
Reboot.
b.
Click the Restart System button.
c.
When the confirmation message appears, click OK. The SPA400 reboots.
Downloaded from
www.Manualslib.com
manuals search engine
Page 109 / 286
Administering the SPA400 and Voice Mail Service
Upgrading the Firmware for the SPA400
SPA9000 Voice System Administration Guide
107
5
d.
When the
Reboot OK
. Go to Setup page?
message appears, click OK and wait
for 60 seconds (the time required for the SPA9000 to re-register with SPA400).
Upgrading the Firmware for the SPA400
As needed, you can download new firmware and then install it on the SPA400.
STEP 1
Download the latest SPA400 firmware from the following URL:
STEP 2
Connect to the SPA400 administration web server. (See
“Connecting to the
SPA400 Administration Web Server,” on page103
.)
STEP 3
Click
Administration
tab >
Firmware Upgrade.
STEP 4
Click Browse.
SPA400 Administration tab > Firmware Upgrade page
STEP 5
Find the binary (.bin file) that you extracted to your Desktop, and click Open. The
selected file appears in the
File Path
field on the
Firmware Upgrade
page.
STEP 6
Click Upgrade.
Downloaded from
www.Manualslib.com
manuals search engine
Page 110 / 286
Administering the SPA400 and Voice Mail Service
Configuring a SPA400 to Interoperate with the SPA9000
SPA9000 Voice System Administration Guide
108
5
STEP 7
When the confirmation message appears, click OK.
STEP 8
When the
Setup
page reappears, verify that the
Firmware Version
number
matches the firmware version that you installed. You have successfully upgraded
the firmware.
SPA400 Main Page: Firmware Version
NOTE
You may need to refresh your browser to display the updated banner
reflecting the new version number.
Configuring a SPA400 to Interoperate with the SPA9000
A SPA400 must be configured to register the SPA9000. To enable the
interoperation of the two devices, you need to enter corresponding information on
the
SPA9000 Voice > Line
page and on the
SPA400 Setup > SPA9000 Interface
page. For voice mail service, additional entries are needed on the
SPA400 Setup
> Voicemail Server
page.
Be aware of the following factors:
•
You need to complete this procedure for each SPA400, whether it is used as a
PSTN gateway or as a voice mail server.
•
You need to configure a SPA9000 line interface for each SPA400. See
“Configuring a Line Interface for a SPA400 (PSTN or Voice Mail),” on page 60
.
Downloaded from
www.Manualslib.com
manuals search engine

Rate

3.5 / 5 based on 2 votes.

Popular Linksys Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top