1. Home
    2. /
  2. Manuals
    3. /
  3. Inteno
    4. /
  4. X5671B
    5. /
  5. 10
Page 46 / 82 Scroll up to view Page 41 - 45
X5671
User’s Guide
41
If the
Network Authentication
is WPA, enter
WPA Group Rekey Interval
, the
IP
address
and
Port number
of Radius server,
Radius Key
, WPA Encryption Method
(TKIP, AES, TKIP+AES), enable or disable
WEP encryption
. If WEP Encryption is
enabled, select the
Encryption Strength
with 64bits or 128bits, select the current
Key Index
and enter the key and four keys when necessary.
If the
Network Authentication
is WPA-PSK (pre-shared key), enter the WPA
Pre-Shared Key and enter
WPA Group Rekey Interval
,
WPA Encryption Method
(TKIP, AES, TKIP+AES), enable or disable
WEP encryption
. If WEP Encryption is
enabled, select the
Encryption Strength
with 64bits or 128bits, select the current
Key Index
and enter the key and four keys when necessary.
Page 47 / 82
X5671
User’s Guide
42
If the
Network Authentication
is WPA2, select Enable or Disable for
WPA2
Pre-authentication
, enter value of Network Re-Auth Interval, enter value of
WPA
Group Rekey Interval
, the
IP address
and
Port number
of Radius server,
Radius
Key
, WPA Encryption Method (TKIP, AES, TKIP+AES), enable or disable
WEP
encryption
. If WEP Encryption is enabled, select the
Encryption Strength
with
64bits or 128bits, select the current
Key Index
and enter the key and four keys
when necessary.
If the
Network Authentication
is WPA2-PSK (pre-shared key), enter the WPA
Pre-Shared Key and enter
WPA Group Rekey Interval
,
WPA Encryption Method
(TKIP, AES, TKIP+AES), enable or disable
WEP encryption
. If WEP Encryption is
enabled, select the
Encryption Strength
with 64bits or 128bits, select the current
Key Index
and enter the key and four keys when necessary.
If the
Network Authentication
is mixed WPA2/WPA, select Enable or Disable for
WPA2 Pre-authentication
, enter value of Network Re-Auth Interval, enter value of
WPA Group Rekey Interval
, the
IP address
and
Port number
of Radius server,
Radius Key
, WPA Encryption Method (TKIP, AES, TKIP+AES), enable or disable
WEP encryption
. If WEP Encryption is enabled, select the
Encryption Strength
with 64bits or 128bits, select the current
Key Index
and enter the key and four
keys when necessary.
Page 48 / 82
X5671
User’s Guide
43
If the
Network Authentication
is Mixed WPA2/WPA-PSK (pre-shared key), enter
the WPA Pre-Shared Key and enter
WPA Group Rekey Interval
,
WPA Encryption
Method
(TKIP, AES, TKIP+AES), enable or disable
WEP encryption
. If WEP
Encryption is enabled, select the
Encryption Strength
with 64bits or 128bits,
select the current
Key Index
and enter the key and four keys when necessary
Click Save/Apply to save the configuration.
MAC Filter
With this configuration, you could allow or deny wireless to access the device by
wireless MAC address filtering feature. It is disabled as default.
Figure 53: Wireless MAC Filter Configuration
Global Setting
Select the
MAC Restrict Mode
from one of Disable (no MAC filter), Allow (only
those PCs with MAC addresses in the table can surf Internet) and Deny (only
those PCs with MAC addresses in the table can not surf Internet).
Click
Add
to add an entry or
Remove
to remove the specified entry.
Figure 54: Add a Wireless MAC Address
Global Setting
Enter the
MAC Address of wireless client
Click Save/Apply to save the configuration.
Page 49 / 82
X5671
User’s Guide
44
Wireless Bridge
The wireless bridge feature is also known as WDS, Wireless Distribution System).
Figure 55: Wireless Bridge Configuration
Global Setting
Set the
AP mode
as Access Point or Wireless Bridge
When the
AP mode
is set to Wireless Bridge, the
Wireless Restrict
determine
where it can communicate with all other wireless bridges and also wireless
clients (set
Bridge Restrict
is Disabled) or just the specified MAC addresses of
below wireless bridge devices (set
Bridge Restrict
is Enable).
Click Reflash to get the updated information
Click
Save/Apply
to save the configuration
Advanced
This page allows you to configure advanced parameters for wireless communication.
Figure 56: Wireless Setting – Advanced
Page 50 / 82
X5671
User’s Guide
45
Global Setting
Enable
AP Isolation
if you do not want AP to be able to communicate with each
other.
Set the W
ireless Communication Band
. If you do not know it, please it as default.
Select the
channel
from the list
Enter the value of
Auto Channel Timer
Set the
54g Rate
(Wireless Communication Rate), AUTO means to use the
highest rate if possible)
Set the
Rate for Multicast Packets
, AUTO means to use the highest if possible.
Set the
Basic Rate
Set the
Fragmentation Threshold
values from 256 to 2364 bytes. If the value is
too small, it may cause a result in poor performance.
Set the
RTS (Ready to Send) Threshold
Set
DTIM Interval.
DTIM stands for Delivery Traffic Indication Message. This is a
beacon and is a countdown informing wireless clients of the next window for
listening to broadcast and multicast messages. It is a wake-up interval for clients
in power-saving mode.
Set
Beacon Interval
. The interval in milliseconds between beacon transmissions.
Set the
Maximum Associated Wireless Client
Set
XPress Technology
enabled or disabled.
Set
54g Mode
to 54g Auto, 54g Performance, 802.11b, 54g LRS (limited rate
support).
Set
54g Protection
to AUTO if there are 802.11g and 802.11b coexisting in the
wireless network.
Set
Afterburner Technology
Set
Preamble Type
. A preamble is a signal that sync up the timing between
devices.
Set
Transmission Power
. Larger value means more coverage.
Quality of Service
The device provides wireless quality of service, Wi-Fi Multimedia.
Figure 57: Wireless Setting – Quality of Service
Global Setting
Select to enable or disable
WMM (Wi-Fi Multimedia)
Select
to
enable
or
disable
WMM
No
Acknowledgement
.
Enabling
no-acknowledge can result in more efficient throughput but high error rates

Rate

124.8 / 5 based on 304 votes.

Popular Inteno Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top