1. Home
    2. /
  2. Manuals
    3. /
  3. Inteno
    4. /
  4. X5671
    5. /
  5. 12
Page 56 / 82 Scroll up to view Page 51 - 55
X5671
User’s Guide
51
Internet Time
This page allows you to sync up the real time clock from Internet. .
Figure 66: Internet Time Configuration
Global Setting
Check to
Automatically synchronize with Internet time servers
Click
Save
to save your settings
Access Control
This submenu provides you local (LAN) or remote (WAN) access to the device. This
may help the IT support staff to configure the router locally or remotely.
Service
Figure 67: Management Configuration – Access Control: Service
Page 57 / 82
X5671
User’s Guide
52
Global Setting:
Specify the method by which you wish to access the router locally or remotely by
selecting it. The following are the methods available for local and remote access:
FTP
HTTP
ICMP (Ping)
SSH
TELNET
TFTP
Click
Save/Apply
to save the configuration.
IP Address
Figure 68: Management Configuration – Access Control: IP Address
Click to enable or disable Access Control by IP address.
Click
Add
to add IP address.
Check
Remove
and click
Remove
to remove the specified entry.
Figure 69: Management Configuration – Access Control: Add IP Address
Global Setting:
Add the IP Address which is permitted to access the device and execute the
management service.
Click Save/Apply to save the settings
.
Password
There are three levels of access accounts: admin, support, and user. The user name
“admin” has unrestricted access to change and view configuration of the device. The
user name “support” is used to allow an ISP technician to access the device for
maintenance and to run diagnostics. The user name “user” can access the device,
Page 58 / 82
X5671
User’s Guide
53
view configuration settigns and statistics, as well as updaet the device software.
Figure 70: Management Configuration – Access Control: Password
Global Setting:
Select the level of
Username
Enter the
Old Password
Enter the
New Password
and
Confirm Password
Click
Save/Apply
to save the configuration.
Page 59 / 82
X5671
User’s Guide
54
Update Software
This page allows you to upgrade the software (firmware).
Figure 71: Management Configuration – Update Software
Global Setting:
First of all, you have to get the updated software (firmware) from ISP or
manufacture.
Click
Browser
to specify the location and filename
Click
Update Software
to start the process. It could take minutes to complete it.
Save / Reboot
This page allows you to save current configuration and reboot to use the settings.
Figure 72: Management Configuration – Save/Reboot (no picture)
Global Setting
Click
Save/Reboot to
save the changes and reboot the device
.
Click Reboot to discard changes and reboot the device only
Page 60 / 82
X5671
User’s Guide
55
Appendix A - Configuring the Internet Settings
This appendix provides instructions for configuring the Internet settings on your
computers to work with the device.
Configuring Ethernet PCs
Before you begin
By default, the device automatically assigns the required Internet settings to your PCs.
You need to configure the PCs to accept this information when it is assigned.
Note
In some cases, you may want to assign Internet information
manually to some or all of your computers rather than allow the
device to do so. See
Assigning static Internet information to your PCs section.
If you have connected your LAN PCs via Ethernet to the device, follow the
instructions that correspond to the operating system installed on your PC:
Windows® XP PCs
Windows 2000 PCs
Windows Me PCs
Windows\ 95, 98 PCs
Windows NT 4.0 workstations
If you want to allow Wireless PCs to access your device, follow the instructions in
Configuring Wireless PCs below..
Windows® XP PCs
In the Windows task bar, click the
Start
button, and then click
Control Panel
.
Double-click the Network Connections icon.
In the
LAN or High-Speed Internet
window, right-click on the icon corresponding to
your network interface card (NIC) and select
Properties
. (Often, this icon is labelled
Local Area Connection
).The
Local Area Connection
dialog box is displayed with a list
of currently installed network items.
Ensure that the check box to the left of the item labelled
Internet Protocol TCP/IP
is
checked and click
Properties
.
In the Internet Protocol (TCP/IP) Properties dialog box, click the radio button labelled
Obtain an IP address automatically. Also click the radio button labelled Obtain DNS
server address automatically.
Click
OK
twice to confirm your changes, and then close the Control Panel.
Windows 2000 PCs
First, check for the IP protocol and, if necessary, install it:
In the Windows task bar, click the
Start
button, point to
Settings
, and then click
Control
Panel
.
Double-click the Network and Dial-up Connections icon.
In the
Network and Dial-up Connections
window, right-click the Local Area Connection
icon, and then select
Properties
. The
Local Area Connection Properties
dialog box is

Rate

4.5 / 5 based on 2 votes.

Popular Inteno Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top