Huawei HG8245T Router Manual PDF (Setup & Configuration Guide)

Page 116 / 429 Scroll up to view Page 111 - 115

----End

Result

The user can watch program1 on TV.

3.2.7 Configuring GPON FTTH Layer 3 Bridge Multicast Service on

the NMS

This topic describes how to configure the multicast service when an ONT is connected to an

OLT through a GPON port.

Prerequisite

The OLT must be added to the U2000.

Example Network

l

The ONT is connected to the OLT in Layer 3 bridge mode.

l

The OLT uses IGMP proxy, which is a Layer 2 multicast protocol.

l

The IGMP version of the multicast VLAN is IGMPv3.

l

Multicast programs are configured statically.

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

108

Page 117 / 429

Figure 3-6

Configuring the GPON FTTH multicast service

Multicast Source

OLT

LAN Switch

Optical splitter

U2000

STB

TV

BRAS

ONT

Procedure

l

Add the ONT to the U2000 in profile mode.

1.

Perform the following operations to add an MDU (not managed by the NAT

agent) that supports xPON upstream transmission.

(1)

On the topological navigation tree, select the required ODN under the OLT node.

Select the splitter under the ODN, right-click, and then choose

New

>

ONU

; or

select the splitter under the ODN, right-click the blank area on the

Physical

Root

interface on the right side, and then choose

New

>

ONU

.

(2)

On the interface that is displayed, set the parameters on the

Basic Parameters

and

Network Management Channel Parameters

tab pages (on this interface,

the ONU that supports the GPON upstream mode is considered as an example).

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

109

Page 118 / 429

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

110

Page 119 / 429

NOTE

l

When the OLT works in the profile mode, the ONU that supports the GPON upstream

mode needs to be bound with the GPON line profile.

l

When the OLT works in the distributed mode, the ONU that supports the GPON upstream

mode needs to be bound with the ONU capacity profile.

l

When the

OLT sets network management channel parameters

check box is cleared,

ONUs are configured and managed remotely on the OLT through the OMCI protocol.

l

When the

OLT sets network management channel parameters

check box is selected,

ONUs are configured and managed remotely on the OLT through the SNMP protocol.

l

Do not add the SNMP parameters on the ONU through the serial port, but issue the SNMP

profile from the OLT to the ONU only.

(3)

Click

OK

.

(4)

In the Main Topology, double-click the required OLT in the

Physical Root

navigation tree; or right-click the required OLT and choose

NE Explorer

from

the shortcut menu.

(5)

Choose

VLAN

from the navigation tree.

(6)

On the

VLAN

tab page, right-click and choose

Add

from the shortcut menu.

(7)

In the dialog box that is displayed, set the parameters.

–

VLAN ID: 4000

–

Type: Smart VLAN

(8)

Click

–

Click the

Upstream Port

tab and add upstream port 0/19/0 as the upstream

port of the VLAN.

–

Click the

L3 Interface

tab and set the parameters.

–

Configure L3 Interface: selected

–

IP Address: 192.168.50.4

(9)

Click

Finish

.

(10) Choose

GPON

>

GPON Management

from the navigation tree.

(11)

On the

GPON ONU

tab page, set the filter criteria or click

to display the

GPON ONUs.

(12)

In the information list, select the record where the shelf, slot, port, and ONU IDs

are 0, 2, 1, and 0 respectively and click the

ServicePort Info

tab in the lower

pane.

(13)

On the

ServicePort Info

tab page, right-click and choose

Add

from the shortcut

menu.

(14)

In the dialog box that is displayed, set the parameters.

–

Connection Type: LAN-GPON

–

VLAN ID: 4000

–

Interface Selection: 0/2/1/0/0

–

Service Type: Multi-Service VLAN

–

User VLAN: 4000

–

Keep the upstream and downstream settings the same: selected

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

111

Page 120 / 429

–

Upstream Traffic Name: ip-traffic-table_6 (it is recommended that you use

the default profile ip-traffic-table_6 because the OLT does not limit the rates

of service streams in the management VLAN)

(15) Click

OK

.

2.

Configure a DBA profile.

(1)

Choose

Configuration

>

Access Profile Management

from the main menu. In

the dialog box that is displayed, choose

PON Profile

>

GPON Profile

from the

navigation tree.

(2)

Click the

DBA Profile

tab.

(3)

Right-click and choose

Add Global Profile

from the shortcut menu.

(4)

In the dialog box that is displayed, set the parameters.

–

Name: FTTx

–

T-CONT type: Maximum Bandwidth

–

Maximum Bandwidth: 32768

(5)

Click

OK

.

(6)

In the information list, right-click the record and choose

Download to NE

from

the shortcut menu.

(7)

In the dialog box that is displayed, select the required NE(s), and click

OK

.

3.

Configure a line profile.

In a line profile, a GEM port can be bound to up to eight service streams. In a GEM

port, different GEM connections need to be set up for different service streams.

In this example, the mapping between GEM ports and MDU-side services is

implemented through VLANs, and the service streams of each service are mapped to

GEM port 1. In addition, different GEM connections are set up for the management

VLAN and the VLANs for the Internet, voice, and multicast services.

(1)

Choose

Configuration

>

Access Profile Management

from the main menu. In

the dialog box that is displayed, choose

PON Profile

>

GPON Profile

from the

navigation tree.

(2)

Click the

Line Profile

tab.

(3)

Right-click and choose

Add Global Profile

from the shortcut menu.

(4)

In the dialog box that is displayed, set the parameters.

–

Set

Name

to

FTTx

.

–

Choose

Base Info.

from the navigation tree and set the parameters.

EchoLife HG8010/HG8240B/HG8245T/HG8247T GPON

Terminal

Service Manual

3 Configuration

Issue 01 (2011-10-18)

Huawei Proprietary and Confidential

112

Rate

Popular Huawei Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share