Page 211 / 232 Scroll up to view Page 206 - 210
5
ONT Downstream User Guide
About This Chapter
This topic describes the configuration flow of the ONT when it is connected to a downstream
TV set, telephone set, STB, PC, Wi-Fi laptop, or USB storage device.
NOTE
Refer to respective operations described in this section according to the type of the terminal connected to
the HG8240/HG8245/HG8247. For details about the terminals that can be connected to the HG8240/
HG8245/HG8247, see
2.2 Typical Network Applications
.
5.1 Using a TV Set
This topic describes the configuration flow of the ONT connected to a downstream TV set.
5.2 Using a STB
This topic describes the configuration flow of the ONT connected to a downstream STB.
5.3 Using a PC
This topic describes the configuration flow of the ONT connected to a downstream PC.
5.4 Using a Telephone Set
This topic describes the configuration flow of the ONT connected to a downstream telephone
set.
5.5 Using a Wi-Fi Laptop
This topic describes the configuration flow of the ONT connected to a Wi-Fi laptop.
5.6 Using a USB Storage Device
This topic describes the configuration flow of the ONT connected to a downstream USB storage
device.
EchoLife HG8240/HG8245/HG8247 GPON Terminal
Service Manual
5 ONT Downstream User Guide
Issue 02 (2011-01-26)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
5-1
Page 212 / 232
5.1 Using a TV Set
This topic describes the configuration flow of the ONT connected to a downstream TV set.
Procedure
Step 1
Connect a TV set to the ONT.
Connect the CATV port of the ONT to the TV set by using a coaxial cable and make sure that
they are properly connected.
Step 2
Turn on the power supply.
Turn on the power supply of the TV set, and press the POWER button on the ONT. If the POWER
LED is always on, it indicates that the ONT is connected to the power supply.
Step 3
Enjoy the high-speed video service.
Watch programs according to the prompts displayed on the screen of the TV set.
----End
5.2 Using a STB
This topic describes the configuration flow of the ONT connected to a downstream STB.
Procedure
Step 1
Connect a STB to the device.
Connect a LAN port of the ONT to the STB by using the STB cable and make sure that they are
connected properly.
Step 2
Turn on the power supply.
Power on the TV set and the STB and then press the POWER button of the ONT. If the POWER
LED is always on, it indicates that the ONT is connected to the power supply.
Step 3
Configure the IP address of the STB.
There are three methods of configuring the IP address of the STB:
l
Configuring the static IP address
l
Obtaining the IP address dynamically through the DHCP server
l
Obtaining the IP address through the PPPoE dialup
NOTE
The service provider determines the specific method to be adopted.
Step 4
Enjoy the high-speed video service.
Watch programs according to the prompts displayed on the screen of the TV set.
----End
5 ONT Downstream User Guide
EchoLife HG8240/HG8245/HG8247 GPON Terminal
Service Manual
5-2
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
Issue 02 (2011-01-26)
Page 213 / 232
5.3 Using a PC
This topic describes the configuration flow of the ONT connected to a downstream PC.
Procedure
Step 1
Connect a PC to the device.
Connect a LAN port of the ONT to the PC by using an Ethernet cable and make sure that they
are connected properly.
Step 2
Turn on the power supply.
Power on the PC and then press the POWER button of the ONT. If the POWER LED is always
on, it indicates that the ONT is connected to the power supply.
Step 3
Configure the IP address of the PC.
There are three methods of configuring the IP address of the PC:
l
Configuring the static IP address
l
Obtaining the IP address dynamically through the DHCP server
l
Obtaining the IP address through the PPPoE dialup
NOTE
The service provider determines the specific method to be adopted.
Step 4
Enjoy the high-speed data service.
Run the Internet Explorer and input correct Web site addresses to browse Web pages.
NOTE
The working parameters of the ONT are configured by the service provider remotely. Hence, the ONT
supports plug and play (PnP) and requires no configuration on the user side.
----End
5.4 Using a Telephone Set
This topic describes the configuration flow of the ONT connected to a downstream telephone
set.
Procedure
Step 1
Connect a telephone set to the device.
Connect the TEL port of the ONT to the telephone set by using a telephone cable and make sure
that they are connected properly.
Step 2
Turn on the power supply.
Press the POWER button on the ONT. If the POWER LED is always on, it indicates that the
ONT is connected to the power supply.
Step 3
Enjoy the high-quality voice service.
EchoLife HG8240/HG8245/HG8247 GPON Terminal
Service Manual
5 ONT Downstream User Guide
Issue 02 (2011-01-26)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
5-3
Page 214 / 232
After picking up the telephone, dial the callee number, and wait for the callee to answer the
telephone.
----End
5.5 Using a Wi-Fi Laptop
This topic describes the configuration flow of the ONT connected to a Wi-Fi laptop.
Procedure
Step 1
Turn on the power supply.
Turn on the power supply of the Wi-Fi laptop, and press the POWER button on the ONT. If the
POWER LED is always on, it indicates that the ONT is connected to the power supply.
Step 2
Enable the Wi-Fi function on the ONT.
Press the WLAN button. If the WLAN LED is always on, it indicates that the Wi-Fi function is
enabled. By default, the Wi-Fi function is enabled.
Step 3
Configure the Wi-Fi parameters of the laptop, including the following:
l
Wireless network name (SSID)
l
Wireless network key
NOTE
The service provider determines the parameters to be configured.
Step 4
If WPS is adopted as the encryption mode for the STA (Wi-Fi laptop) to request access to the
wireless network, press the WPS button on the side panel of the ONT and press the WPS button
on the laptop (or run the WPS program installed on the laptop) within two minutes.
Step 5
Enjoy the high-speed data service.
Run the Internet Explorer and input correct Web site addresses to browse Web pages.
NOTE
l
A Wi-Fi Ethernet card must be installed on the laptop.
l
The working parameters of the ONT are configured by the service provider remotely. Hence, the
ONT supports plug and play (PnP) and requires no configuration on the user side.
----End
5.6 Using a USB Storage Device
This topic describes the configuration flow of the ONT connected to a downstream USB storage
device.
Procedure
Step 1
Turn on the power supply.
Press the POWER button on the ONT. If the POWER LED is always on, it indicates that the
ONT is connected to the power supply.
Step 2
Connect a USB storage device to the ONT.
5 ONT Downstream User Guide
EchoLife HG8240/HG8245/HG8247 GPON Terminal
Service Manual
5-4
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
Issue 02 (2011-01-26)
Page 215 / 232
Connect the USB port of the ONT to the USB storage device by using a USB data cable and
make sure that they are properly connected.
Step 3
Log in to the ONT Web page on a PC. Then, configure associated USB parameters. For
details ,see
6.3.6 USB LED Off
. After the configuration is complete, you can download files
through the ONT.
----End
EchoLife HG8240/HG8245/HG8247 GPON Terminal
Service Manual
5 ONT Downstream User Guide
Issue 02 (2011-01-26)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
5-5

Rate

3.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top