1. Home
    2. /
  2. Manuals
    3. /
  3. DrayTek
    4. /
  4. Vigor2130n
    5. /
  5. 45
Page 221 / 241 Scroll up to view Page 216 - 220
Vigor2130 Series User’s Guide
213
4.13.2 Routing Table
Click
Diagnostics
and click
Routing Table
to open the web page.
Destination
Display the IP address for destination network or
destination host.
Gateway
Display the gateway address or “*” if none set.
Genmask
Display
the netmask for the destination net;
'255.255.255.255' is for a host destination and '0.0.0.0' is
for the default route.
Flags
Different codes represent different routing status.
U
- route is up.
H
- t
arget is a host
G
-
use gateway
R
-
reinstate route for dynamic routing
D
-
dynamically installed by daemon or redirect
M
-
modified from routing daemon or redirect
A
-
installed by addrconf
C
-
cache entry
!
-
reject route
Metric
Display the distance to the target (usually counted in hops).
Ref
Display number of references to this route. (Not used in the
Linux kernel.)
Use
Display count of lookups for the route. Depending on the
use of -F and –C, this will be either route cache misses (-F)
or hits (-C).
Iface
Display interface to which packets for this route will be
sent.
Refresh
Click it to reload the page.
Page 222 / 241
Vigor2130 Series User’s Guide
214
4.13.3 System Log
Click
Diagnostics
and click
System Log
to open the web page.
Time
Display the time of the system log entry.
Level
Display the severity level of the system log entry.
Type
Display the type or subsystem of the system log entry.
Message
Display a short description of the system log entry.
Auto-refresh
Check it to enable auto-refresh function.
Reverse
Check
it to have newest log entries presented first.
Refresh
Click it to reload the page.
Export
Click it to export the log as a text file.
4.13.4 Traffic Overview
This page offers an overview of general traffic statistics for all connecting ports.
Port
Display the interface that data transmission passing
through.
Page 223 / 241
Vigor2130 Series User’s Guide
215
Packets
Display the packet sizes for data transmission in receiving
and sending.
Bytes
Display the number of received and transmitted bytes per
port.
Errors
Display the number of the error occurred in data receiving
and data sending.
Drops
Display the number of the data lost in receiving and
sending.
Filtered
Display the number of received frames filtered by the
forwarding process.
Auto-refresh
Check it to enable auto-refresh function.
Refresh
Click it to reload the page.
Clear
Click it to clear the counters for all ports.
4.13.5 Detailed Statistics
This page display detailed statistics for WAN/LAN interface.
Rx Packets
Display the counting number of the packet received.
Rx Octets
Display the total received bytes.
Rx Unicast
Display the counting number of the received unicast
packet.
Page 224 / 241
Vigor2130 Series User’s Guide
216
Rx Broadcast
Display the counting number of the received broadcast
packet.
Rx Pause
Display the counting number of the received pause packet.
RX 64 Bytes
Display the number of 64-byte frames in good and bad
packets received.
RX 65-127 Bytes
Display the number of 65 ~ 127-byte frames in good and
bad packets received.
RX 128-255 Bytes
Display the number of 128 ~ 255-byte frames in good and
bad packets received.
RX 256-511 Bytes
Display the number of 256 ~ 511-byte frames in good and
bad packets received.
RX 512-1023 Bytes
Display the number of 512 ~ 1023-byte frames in good and
bad packets received.
RX 1024- 1526 Bytes
Display the number of 1024-1522-byte frames in good and
bad packets received.
RX 1527 Bytes
Display the number of 1527-byte frames in good and bad
packets received.
Rx Low
Display the low queue counter of the packet received.
Rx Normal
Display the normal queue counter of the packet received.
Rx Medium
Display the medium queue counter of the packet received.
Rx High
Display the high queue counter of the packet received.
Rx Drops
Display the number of frames dropped due to the lack of
receiving buffer.
Rx CRC/Alignment
Display the number of Alignment errors packets received.
Rx Undersize
Display the number of short frames (<64 Bytes) with valid
CRC.
Rx Oversize
Display the number of long frames (according to
max_length register) with valid CRC.
Rx Fragments
Display the number of short frames (< 64 bytes) with
invalid CRC.
Rx Jabber
Display the number of long frames (according
tomax_length register) with invalid CRC.
Rx Filtered
Display the filtered number of the packet received.
Tx Packets
Display the counting number of the packet transmitted.
Tx Octets
Display the total transmitted bytes.
Tx Unicast
Display the show the counting number of the transmitted
unicast packet.
Tx Multicast
Display the show the counting number of the transmitted
multicast packet.
Tx Broadcast
Display the counting number of the transmitted broadcast
packet.
Tx Pause
Show the counting number of the transmitted pause packet.
Page 225 / 241
Vigor2130 Series User’s Guide
217
Tx 64 Bytes
Display the number of 64-byte frames in good and bad
packets transmitted.
Tx 65-127 Bytes
Display the number of 65 ~ 127-byte frames in good and
bad packets transmitted.
Tx 128-255 Bytes
Display the number of 128 ~ 255-byte frames in good and
bad packets transmitted.
Tx 256-511 Bytes
Display the number of 256 ~ 511-byte frames in good and
bad packets transmitted.
Tx 512-1023 Bytes
Display the number of 512 ~ 1023-byte frames in good and
bad packets transmitted.
Tx 1024- 1526 Bytes
Display the number of 1024 ~ 1522-byt frames in good and
bad packets transmitted.
Tx 1527 Bytes:
Display the number of 1527-byte frames in good and bad
packets transmitted.
Tx Low
Display the low queue counter of the packet transmitted.
Tx Normal
Display the normal queue counter of the packet
transmitted.
Tx Medium
Display the medium queue counter of the packet received.
Tx High
Display the high queue counter of the packet received.
Tx Drops
Display the number of frames dropped due to excessive
collision, late collision, or frame aging.
Tx lat/Exc.Coll.
Display the number of Frames late collision or excessive
collision Error, which switch transmitted
Auto-refresh
Check it to enable auto-refresh function.
Refresh
Click it to reload the page.
Clear
Click it to clear the counters for all ports.
4.13.6 MAC Address Table
The MAC Address Table contains up to 8192 entries, and is sorted first by VLAN ID, then by
MAC address.
Each page shows up to 999 entries from the MAC table, default being 20, selected through the
"entries per page" input field. When first visited, the web page will show the first 20 entries
from the beginning of the MAC Table. The first displayed will be the one with the lowest
VLAN ID and the lowest MAC address found in the MAC Table.
The
Start from MAC address
and
VLAN
input fields allow the user to select the starting
point in the MAC Table. Clicking the
Refresh
button will update the displayed table starting
from that or the closest next MAC Table match. In addition, the two input fields will assume
the value of the first displayed entry, allowing for continuous refresh with the same start
address.
The button
>>
will use the last entry of the currently displayed VLAN/MAC address pairs as a
basis for the next lookup. When the end is reached the text "no more entries" is shown in the
displayed table, use the
l<<
button to start over.

Rate

4 / 5 based on 1 vote.

Popular DrayTek Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top