1. Home
    2. /
  2. Manuals
    3. /
  3. DrayTek
    4. /
  4. Vigor2130n
    5. /
  5. 41
Page 201 / 241 Scroll up to view Page 196 - 200
Vigor2130 Series User’s Guide
193
Adding a New Rule
Click
Add New Rule
to configure a new rule for IPv6 Firewall.
Note:
You can set up to 20 sets of IPv6 rules.
Name
Type a name for the rule.
Protocol
Specify a protocol for this rule.
Source IP Type
Determine the IP type as the source.
Source IP
Type the IP address here if you choose
Single
as
Source
IP Type
.
Source Subnet
Type the subnet mask here if you choose
Subnet
as
Source IP Type
.
Destination IP Type
Determine the IP type as the destination.
Destination IP
Type the IP address here if you choose
Single
as
Destination IP Type
.
Page 202 / 241
Vigor2130 Series User’s Guide
194
Destination Subnet
Type the subnet mask here if you choose
Subnet
as
Destination IP Type
.
Source Start Port
Type a value as the source start port. Such value will be
available only TCP/UDP is selected as the protocol.
Source End Port (optional)
Type a value as the source end port. Such value will be
available only TCP/UDP is selected as the protocol.
Destination Start Port
Type a value as the destination start port. Such value will
be available only TCP/UDP is selected as the protocol.
Destination End Port (optional)
Type a value as the destination end port. Such value will be
available only TCP/UDP is selected as the protocol.
Action
Set the action that the router will perform for the packets
through the protocol of IPv6.
Accept –
If the IPv6 packets fit the condition listed in this
page, the router will let it pass through.
Drop -
If the IPv6 packets fit the condition listed in this
page, the router will block it.
Example:
Refer to the following example.
1.
Use TSPC mode to connect to IPv6 network.
PC get ipv6 IP: 2001:5c0:1503:7400:30e4:139d:53c8:3a1e
2.
Connect PC to http://www.ipv6.org/
with IPv6 IP address.
A message will appear from the web page:
Welcome to the IPv6 Information Page!
You are using IPv6 from 2001:5c0:1503:7400:30e4:139d:53c8:3a1e
3.
Set firewall rule to block all TCP traffic from this IP address.
4.
Open
IPv6 >> IPv6 Firewall
Setup
and press
Add New Rule
.
In the following dialog, please configure the page with the following values.
Page 203 / 241
Vigor2130 Series User’s Guide
195
5.
Connect PC to http://www.ipv6.org/
with IPv6 IP address again.
A message will appear from web page:
Welcome to the IPv6 Information Page!
You are using IPv4 from 114.37.132.219
4.10.4 IPv6 Routing
This page displays the routing table for the protocol of IPv6.
Device
Display the
interface name (eth0, eth1, fp, etc..)that
used to transfer packets with addresses matching the
prefix.
Prefix
The IPv6 address prefix.
Metric
Display the
distance to the target (usually counted in
hops). It is not used by recent kernels, but may be
needed by routing daemons.
Expires
Display the lifetime of the route.
MTU
Display t
he largest size (in bytes) of a packet.
Page 204 / 241
Vigor2130 Series User’s Guide
196
Advmss
Display t
he largest size (in bytes) of an unfragmented
piece of a routing advertisement.
Hoplimit
Display t
he number of network segments on which the
packet is allowed to travel before discarded.
Auto-refresh
Check this box to enable an automatic refresh of the page
at regular intervals.
4.10.5 IPv6 Neighbour
IPv6 uses neighbor discovery protocol to find out neighbors on the same link.
Device
The interface name of the link where the neighbor is on.
IP Address
The IPv6 address of the neighbor.
MAC Address
The link-layer address of the neighbor.
State
Possible states include:
incomplete
- address resolution is in progress.
reachable
- neighbor is reachable.
stale
– neighbor(s) may be unreachable but not verified
until a packet is sent).
delay
- neighbor may be unreachable and a packet was sent.
probe
- neighbor may be unreachable and probes are sent
to verify the reachability.
Auto-refresh
Check this box to enable an automatic refresh of the page
at regular intervals.
4.10.6 IPv6 TSPC Status
IPv6 TSPC status web page could help you to diagnose the connection status of TSPC. TSPC
log contains some debug information from program.
If TSPC has not configured properly, the router will display the following page when the user
tries to connect through TSPC connection.
Page 205 / 241
Vigor2130 Series User’s Guide
197
When TSPC configuration has been done, the router will start to connect. The connecting page
will be shown as below:
When the router detects all the information, the screen will be shown as follows. One set of
TSPC prefix
and
prefix length
will be obtained after the connection between TSPC and
Tunnel broker built.
Connection Status
It will bring out different pages to represent IPv6
disconnection, connecting and connected.

Rate

4 / 5 based on 1 vote.

Popular DrayTek Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top