DrayTek Vigor2130n Router Manual PDF (Setup & Configuration Guide)

Page 186 / 241 Scroll up to view Page 181 - 185

Vigor2130 Series User’s Guide

178

z

None

The encryption mechanism is turned off.

z

WEP

Accepts only WEP clients and the encryption key should be entered in WEP Key.

Default Key

All wireless devices must support the same WEP

encryption bit size and have the same key.

Key1-Key4

Four keys

can be entered here, but only one key can be

selected at a time. The format of WEP Key is restricted to

5 ASCII characters or 10 hexadecimal values in 64-bit

encryption level, or restricted to 13 ASCII characters or 26

hexadecimal values in 128-bit encryption level. The

allowed content is the ASCII characters from 33(!) to

126(~) except '#' and ',' .

Authentication Mode

Choose OPEN or SHARED as the authentication mode.

OPEN: Set wireless to authentication open mode.

SHARED: Set wireless to authentication shared mode.

z

WPA-PSK

Accepts only WPA clients and the encryption key should be entered in PSK. The WPA

encrypts each frame transmitted from the radio using the key, which either PSK

(Pre-Shared Key) entered manually in this field below or automatically negotiated via

802.1x authentication.

Page 187 / 241

Vigor2130 Series User’s Guide

179

WPA Mode

Select WPA, WPA2 or Auto as the type.

WPA Algorithm

Select TKIP, AES or auto as the algorithm for WPA.

WPA Pre-Shared Key

Either

8~63

ASCII characters, such as 012345678..(or 64

Hexadecimal digits leading by 0x, such as

"0x321253abcde...").

z

WPA-RADIUS

The built-in RADIUS client feature enables the router to assist the remote dial-in user or

a wireless station and the RADIUS server in performing mutual authentication. It enables

centralized remote access authentication for network management.

Type

The WPA encrypts each frame transmitted from the radio

using the key, which either PSK (Pre-Shared Key) entered

manually in this field below or automatically negotiated

via 802.1x authentication. Select WPA, WPA2 or Auto as

WPA mode.

Page 188 / 241

Vigor2130 Series User’s Guide

180

WPA Algorithm

Choose the WPA algorithm, TKIP, AES or Auto.

Server IP Address

Enter the IP address of RADIUS server.

Destination Port

The UDP port number that the RADIUS server is using.

The default value is 1812, based on RFC 2138.

Shared Secret

The RADIUS server and client share a secret that is used

to authenticate the messages sent between them. Both

sides must be configured to use the same shared secret.

z

WPS

WPS (Wi-Fi Protected Setup)

provides easy procedure to make network connection

between wireless station and wireless access point (vigor router) with the encryption

of WPA and WPA2.

Configure via Push Button

Click

Start PBC

to invoke Push-Button style WPS setup

procedure. The router will wait for WPS requests from

wireless clients about two minutes. The WPS LED on the

router will blink fast when WPS is in progress. It will

return to normal condition after two minutes. (You need to

setup WPS within two minutes)

Configure via Client PinCode

Type the PIN code specified in wireless client you

wish to connect, and click

Start PIN

button. The WLAN

LED on the router will blink fast when WPS is in progress.

It will return to normal condition after two minutes. (You

need to setup WPS within two minutes.

It is the simplest way to build connection between wireless network clients and vigor

router. Users do not need to select any encryption mode and type any long encryption

passphrase to setup a wireless client every time. He/she only needs to press a button on

wireless client, and WPS will connect for client and router automatically.

Page 189 / 241

Vigor2130 Series User’s Guide

181

Note:

Such function is available for the wireless station with WPS supported.

There are two methods to do network connection through WPS between AP and Stations:

pressing the

Start PBC

button or using

PIN Code

.

On the side of Vigor 2130 series which served as an AP, press

WPS

button once on the

front panel of the router or click

Start PBC

on web configuration interface. On the side

of a station with network card installed, press

Start PBC

button of network card.

If you want to use PIN code, you have to know the PIN code specified in wireless client.

Then provide the PIN code of the wireless client you wish to connect to the vigor router.

Page 190 / 241

Vigor2130 Series User’s Guide

182

4.8.3 Access Control

For additional security of wireless access, the

Access Control

facility allows you to restrict

the network access right by controlling the wireless LAN MAC address of client. Only the

valid MAC address that has been configured can access the wireless LAN interface. By

clicking the

Access Control

, a new web page will appear, as depicted below, so that you

could edit the clients' MAC addresses to control their access rights (deny or allow).

Filter Type

Choose the rule for the MAC addresses displayed in this

page.

Allow List

– all the MAC address of wireless clients listed

here are allowed to do wireless connection.

Deny List

– all the MAC address of wireless clients listed

here will be blocked.

Add a New Entry

Add a new MAC address into the list.

Delete

Delete the selected MAC address in the list. This button

will appear only an entry of MAC Address has been typed.

Cancel

Give up the configuration.

OK

Click it to save the configuration.

4.8.4 Station List

Station List

provides the knowledge of connecting wireless clients now along with its status

code.

Rate

Popular DrayTek Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share