1. Home
    2. /
  2. Manuals
    3. /
  3. DrayTek
    4. /
  4. Vigor2130n
    5. /
  5. 36
Page 176 / 241 Scroll up to view Page 171 - 175
Vigor2130 Series User’s Guide
168
4.7.2 PPTP Remote Dial-in
You can manage remote access by maintaining a table of remote user profile, so that users can
be authenticated to dial-in via VPN connection.
The router provides
access accounts for dial-in users.
Adding a New User
Click
Add new user
to open the following page.
Username
Type a name for this user.
Full Name
Type full name for this user.
Password
Type the password for this user.
Password (again)
Type the password again for confirmation.
Allow Disk Sharing
Check this box to have the remote user share the disk
information.
Allow IPSEC/L2TP
Check this box to let the remote user connecting to this
device through IPSEC/L2TP
.
Allow PPTP
Check this box to let the remote user connecting to this
device through PPTP
.
Allow FTP
Check this box to let the remote user connecting to FTP
server via this router.
Delete User
Remove settings on current page and delete the user. This
button is not available for new configuration by pressing
Add a New User
.
Page 177 / 241
Vigor2130 Series User’s Guide
169
When you finish the settings, simply click
OK
to save the configuration. The new user will be
created and displayed on the page.
Editing/Deleting User Settings
To edit a user, click the name link under Username to open the following page. Modify the
settings except Username and then click
OK
to save and exit it. If you want to remove such
user settings, simply click
Delete User
.
4.7.3 IPSec Remote Dial-in
This page allows you to configure IPSec Site-to-Client settings.
Mobile VPN Type
This usually applies to those are remote dial-in user or node
(LAN-to-LAN) which uses dynamic IP address and
Page 178 / 241
Vigor2130 Series User’s Guide
170
IPSec-related VPN connections such as L2TP over IPSec and
IPSec tunnel.
Disabled
– Ignore the configurations set in this page.
Dynamic VPN (IPSec)
– Traffic between this subnet and the
client will travel through the VPN tunnel. If you choose this
type, please specify the IP address and subnet mask for local
network.
L2TP/IPSec
–The range must not overlap the DHCP address
range (if enabled), and must allow for at least one IP address.
Example:
10.10.137.240-10.10.137.245
. If you choose this type,
please specify the IP address range for L2TP/IPSec mode.
Authentication
Shared secret –
Type the shared secret manually and confirm it
again. IPSec remote dial-in clients will use the given secret.
Advanced Settings
Phase 1 (IKE) -
Negotiation of IKE parameters including
encryption, hash, Diffie-Hellman parameter values, and lifetime
to protect the following IKE exchange, authentication of both
peers using either a Pre-Shared Key or Digital Signature (x.509).
The peer that starts the negotiation proposes all its policies to
the remote peer and then remote peer tries to find a
highest-priority match with its policies.
Phase 2 (IPSec) -
Negotiation IPSec security methods
including Authentication Header (AH) or Encapsulating
Security Payload (ESP) for the following IKE exchange and
Page 179 / 241
Vigor2130 Series User’s Guide
171
mutual examination of the secure tunnel establishment.
4.7.4 Remote Dial-in Status
You can find the summary table of all dial-in user status.
Client
Display the name of the VPN IPSec/Mobile client.
Identity
Display the remote ID of the VPN client.
Endpoint
Display the IP address of the VPN client.
IKE Status
Display the status of the phase 1 ISAKMP key exchange.
IKE Alg
Display
the encryption and authentication algorithm used
during phase 1 of the VPN connection Establishment. The
algorithm is used during exchange of key exchange.
ESP Status
Display the status of the phase 2 IPSec ESP key exchange.
ESP Alg
Display the encryption and authentication algorithm used
during phase 2 of the VPN connection Establishment. This
algorithm is used for transporting data, and the choice will
affect the performance of the VPN tunnel.
User Name
Display the dial-in user account.
Interface
Display the connection name assigned by the router.
Remote IP
Display IP address of remote client.
Login Time
Display the system time that the user logs in.
Rx bytes
Display the data total received for such client.
Tx bytes
Display the data total transmitted for such client.
Auto
-
refresh
Check this box to make the system refresh this page
automatically.
Refresh
Click this button to refresh the page immediately.
Page 180 / 241
Vigor2130 Series User’s Guide
172
4.7.5 LAN to LAN
Here you can manage LAN-to-LAN connections by maintaining a table of connection profiles.
You may set parameters including specified connection direction (dial-in or dial-out),
connection peer ID, connection type (VPN connection - including PPTP, IPSec Tunnel) and
corresponding security methods, etc.
The router supports 2 VPN tunnels simultaneously and provides up to
2
profiles. The
following figure shows the summary table.
Name
Indicate the name of the LAN-to-LAN profile.
Endpoint
Display the IP address of the VPN client.
IKE Status
Display the status of the phase 1 ISAKMP key exchange.
IKE Alg
Display
the encryption and authentication algorithm used
during phase 1 of the VPN connection Establishment. The
algorithm is used during exchange of key exchange.
ESP Status
Display the status of the phase 2 IPSec ESP key exchange.
ESP Alg
Display the encryption and authentication algorithm used
during phase 2 of the VPN connection Establishment. This
algorithm is used for transporting data, and the choice will
affect the performance of the VPN tunnel.

Rate

4 / 5 based on 1 vote.

Popular DrayTek Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top