Page 11 / 96
Scroll up to view Page 6 - 10
11
D-Link DWL-7100AP User Manual
To configure the DWL-7100AP, use a computer which is connected to the DWL-7100AP with an Ethernet cable. You may use the web-based
configuration or the AP Manager software to configure your access point. Please refer to page 52 to use the AP Manager software.
Web Configuration Utility
First, disable the Access the Internet using a proxy server function. To disable this function, go to
Control Panel
>
Internet Options
>
Connections
>
LAN Settings
and uncheck the enable box.
Open your web browser program
such as Internet Explorer.
Type the IP address of the DWL-7100AP in the address field (
)
and press
Enter
. Make sure that the IP addresses of the DWL-7100AP and your computer are in the same subnet.
Configuration
After the connection is established, Enter your user name (admin) and your password (leave blank by default). Click
OK
to continue.
Page 12 / 96
1±
D-Link DWL-7100AP User Manual
The
Home
>
Wizard
screen will appear. Please refer
to the
Quick Installation Guide
for more information
regarding the Setup Wizard.
These buttons appear on most of the configuration
screens in this section. Please click on the appropriate
button at the bottom of each screen after you have
made a configuration change.
Home
Page 13 / 96
1²
D-Link DWL-7100AP User Manual
Access Point
WDS with AP
WDS
AP Repeater
AP Client
Open System
Shared Key
Open System/Shared Key
WPA-EAP
WPA-PSK
WPA2-EAP
WPA2-PSK
WPA-Auto-EAP
WPA-Auto-PSK
Open System
Shared Key
Open System/Shared Key
WPA-PSK
WPA2-PSK
WPA-Auto-PSK
Open System
Shared Key
Open System/Shared Key
WPA-PSK
WPA2-PSK
WPA-Auto-PSK
Open System
Shared Key
Open System
Shared Key
WPA-PSK
WPA2-PSK
AP Mode
Authentication Available
Wireless Modes
Page 14 / 96
1³
D-Link DWL-7100AP User Manual
Access Point Mode
Access Point
is selected from the drop-down
menu.
Service Set Identifier (SSID) is the name designated
for a specific wireless local area network (WLAN).
The SSID’s factory default setting is
dlink
. The SSID
can be easily changed to connect to an existing
wireless network or to establish a new wireless
network.
Enable
or
Disable
SSID broadcast. Enabling this
feature broadcasts the SSID across the network.
Auto Channel Scan
is enabled by default. All
devices on the network must share the same
channel.
The radio frequency will vary depending on the
wireless channel that is chosen.
Select
Open System
to communicate the key across the network.
Select
Shared Key
to limit communication to only those devices that share the same WEP settings.
Select
Open System/Shared Key
to allow either form of data encryption.
Select
WPA-EAP
to secure your network with the inclusion of a RADIUS server.
Select
WPA-PSK
to secure your network using a password and dynamic key changes (No RADIUS server required).
Select
WPA2-EAP
to secure your network with the inclusion of a RADIUS server and upgrade the encryption of data with
the Advanced Encryption Standard (AES).
Mode:
SSID:
SSID Broadcast:
Channel:
Authentication:
Wireless Band:
Select
IEEE802.11a
or
IEEE802.11g
.
Page 15 / 96
1´
D-Link DWL-7100AP User Manual
Select
WPA2-PSK
to secure your network using a password and dynamic key changes. No RADIUS server required
and encryption of data is upgraded with the Advanced Encryption Standard (AES).
Select
WPA-Auto-EAP
to allow the client to either use
WPA-EAP
or
WPA2-EAP
.
Select
WPA-Auto-PSK
to allow the client to either use
WPA-PSK
or
WPA2-PSK
.
19216811.live