D-Link DPG-2000W Router Manual PDF (Setup & Configuration Guide)

Page 26 / 44 Scroll up to view Page 21 - 25

26

Web-Based Administration Utility

(Continued)

WEP Key Length

This check box allows users to enable or disable the

WEP feature. The

DPG-2000W

currently supports the

default (shared) WEP key scheme defined in the 802.11

standard, not the mapped key scheme.

WEP Enabled

Note that the “user-controlled” portion of the 64-bit

encryption is just 40 bits (10 Hex digits) and for the

128-bit encryption, 104 bits (26 Hex digits)—3-bytes of

the encryption key are internal to the encryption algorithm.

Simply enter 10 digits in Hexadecimal Format (0-9, a-f)

or 26 digits in Hexadecimal Format depending on the

encryption chosen.

Authentication

Type

WARNING

After changing the settings on this page, you may have to manually change

your wireless card settings accordingly to connect wirelessly to the

DPG-2000W

.

When the “Open system” option is chosen, no

encryption is applied to the exchanged packets between

the

DPG-2000W

wireless station and another wireless

station. Communication with another station or AP,

however, can be successful only if the other station also

is set up to communicate in the “Open system” mode.

When the “Shared key” option is chosen, WEP

encryption must be properly enabled.

Select either Local Access Point or Infrastructure

Station. Local access mode (default) allows the user to

connect only to the

DPG-2000W

. Infrastructure Station

mode enables the user to connect to the

DPG-2000W

and display internet content.

Radio Mode

Page 27 / 44

27

Web-Based Administration Utility

(Continued)

Select Automatic or Manual.

Operation Mode

Automatic:

Manual:

By default, the

DPG-2000W

uses the automatic mode to

automatically select an unused SSID and the clearest

channel upon boot up. This mode is highly recommended

for ease of use.

Allows you to manually set the SSID and channel.

Once you have made your changes on the Settings page, click “Apply” to save

and apply those settings. The following page will appear. Click “OK” to

continue.

If you wish to edit any of your settings you can click “Cancel” to restore the

Settings page to its original settings. If you need help on any of the settings on

the Settings page, you can click “Help” to go to the Help page for more

information on each setting.

WARNING

You will need to reconfigure your wireless settings to match your newly

assigned WEP settings to reconnect to the Administration Utility.

One of the four WEP keys needs to be selected for

transmitting data frames. The

DPG-2000W

can

de-encrypt received data encrypted in any one of the four

keys, but

uses only one of the WEP keys for

transmitting data.

Transmission Key

Selection

Page 28 / 44

28

Options Page

When you click on the Options tab, you will see the page shown below.

Web-Based Administration Utility

(Continued)

You can choose either a firmware or banner page

upload.

Upload Options

If you click the browse button to the right of the field,

file

selection box will appear. To upload a firmware file, be

sure that the file has a .tar.gz extension. To upload a

banner file, be sure that the file has a .jpg extension. For

the best picture on the

DPG-2000W

banner screen, the

.jpg file should be 800 x 600 resolution. The maximum

.jpg size is 2 megabytes (2048 bytes).

WARNING

When uploading the firmware or banner page, do NOT power off or

disconnect the

DPG-2000W

unit. Doing so may damage the equipment.

File Path/Name

Page 29 / 44

29

Web-Based Administration Utility

(Continued)

Reboot

Click the Reboot button to reboot the

DPG-2000W

. The

DPG-2000W

will reboot and your wireless connection will

terminate. The following page will appear. Click “OK” to

continue.

Reset to Factory

Default

Click the Reset to Factory Default button to reset the

DPG-2000W

to its original factory default settings. The

following page will appear. Click “OK” to continue.

Once you have selected your Upload option and entered the File path/name,

click “Apply” to begin the upload. The following page will appear. Click “OK” to

continue.

If you do not wish to continue the firmware or banner upload, click “Cancel” to

restore the Options page.

Page 30 / 44

30

Web-Based Administration Utility

(Continued)

Status Page

This is the current

DPG-2000W

firmware version. It is

important to know which

DPG-2000W

firmware version

you have before calling or emailing technical support.

Following the firmware version is the date the firmware

was released.

When you click on the Status tab, you will see the page shown below.

Firmware Version

Model Name

This is the D-Link model name of your wireless

presentation gateway.

Warning

Please note that resetting the

DPG-2000W

to its factory default settings

will erase all configurations and encryption information you may have set

through the web interface.

If you wish to edit any of your set options you can click “Cancel” to restore the

Options page to its original settings. If you need help on any of the options on

the Options page, you can click “Help” to go to the Help page for more

information on each option.

Rate

Popular D-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share