Page 76 / 100 Scroll up to view Page 71 - 75
76
D-Link DAP-1522 User Manual
Section 4 - Security
Configure WPA-Personal (AP Mode)
It is recommended to enable encryption on your wireless access point before your wireless network adapters. Please
establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption
due to the added overhead.
1. Log into the web-based configuration by opening a web browser
and entering the IP address of the access point (192.168.0.50).
Click on Setup and then click Wireless Settings on the left
side.
2. Next to
Security Mode in the Wireless Security Mode section
,
select
WPA-Personal.
3. Next to
WPA Mode in the WPA section
, select Auto (WPA or
WPA2), WPA2 Only, or WPA Only. Use Auto if you have
wireless clients using both WPA and WPA2.
4. Next to Cipher Type, select TKIP, AES, or TKIP and AES.
5. Next to
Group Key Update Interval
, enter the amount of time before the group key used for broadcast and multicast
data is changed.
6. Next to the
Pre-Shared Key
section, enter a key in the Passphrase field. The key is entered as a passphrase in ASCII
format at both ends of the wireless connection. The passphrase must be between 8-63 characters.
7. Click
Save Settings
at the top of the window to save your settings. If you are configuring the access point with a
wireless adapter, you will lose connectivity until you enable WPA-PSK on your adapter and enter the same passphrase
as you did on the access point.
Page 77 / 100
77
D-Link DAP-1522 User Manual
Section 4 - Security
It is recommended to enable encryption on your wireless access point before your wireless network adapters. Please
establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption
due to the added overhead.
1. Log into the web-based configuration by opening a web browser
and entering the IP address of the access point (192.168.0.50).
Click on
Setup
and then click
Wireless Settings
on the left
side.
2. Next to
Security Mode in the Wireless Security Mode section
,
select
WPA-Enterprise.
3. Next to
WPA Mode in the WPA section
, select
Auto (WPA
or WPA2), WPA2 Only, or WPA
Only. Use Auto if you have
wireless clients using both WPA and WPA2.
4. Next to Cipher Type, select
TKIP, AES, or TKIP
and
AES
.
5. Next to
Group Key Update Interval
, enter the amount of time before the group key used for broadcast and multicast
data is changed.
6. Next to
RADIUS Server IP Address
in the EAP (802.1X) section, enter the IP Address of your RADIUS server.
7. Next to RADIUS Server Port, enter the port you are using with your RADIUS server. 1812 is the default port.
8. Next to
RADIUS Server Shared Secret
, enter the security key.
9. Click
Save Settings
at the top of the window to save your settings.
Configure WPA-Enterprise (AP Mode)
Page 78 / 100
78
D-Link DAP-1522 User Manual
Section 4 - Security
Configure WEP (Bridge Mode)
It is recommended to enable encryption on your wireless access point before your wireless network adapters. Please
establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption
due to the added overhead.
1. Log into the web-based configuration by opening a web browser and entering the IP address of the bridge
(192.168.0.50).
Click on
Setup
and then click
Wireless Settings
.
2. For
Security Mode
in the
Wireless Security Mode
section,
select WEP.
3.
Next to WEP Key Length in the WEP section, select both the type
of input (hexidecimal or ASCII) and the level of encryption (64-
bit or 128-bit). Hex - (recommended) Letters A-F and numbers 0-9
are valid.
4. For the Default WEP Key and the first selection on the drop-down menu, WEP Key 1. Enter a WEP key that you
create in the WEP Key value and Verify WEP Key value fields. Make sure you enter this key exactly on all your
wireless devices. You may enter up to 4 different keys using the Default WEP Key drop-down menu.
5. For
Authentication
, select
Open
or
Shared Key
.
6. Click
Save Settings
to save your settings. If you are configuring the access point with a wireless adapter, you will lose
connectivity until you enable WEP on your adapter and enter the same WEP key as you did on the access point.
Page 79 / 100
79
D-Link DAP-1522 User Manual
Section 4 - Security
Configure WPA-Personal (Bridge Mode)
It is recommended to enable encryption on your wireless access point before your wireless network adapters. Please
establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption
due to the added overhead.
1. Log into the web-based configuration by opening a web browser and entering the IP address of the bridge
(192.168.0.50).
Click on
Setup
and then click
Wireless
Settings
on the left side.
2. Next to
Security Mode in the Wireless Security Mode section
,
select
WPA-Personal.
3. Next to
WPA Mode in the WPA section
, select
Auto (WPA
or
WPA2), WPA2 Only, or WPA
Only. Use
Auto
if you have
wireless clients using both WPA and WPA2.
4. Next to Cipher Type, select
TKIP, AES, or TKIP
and
AES
.
5. Next to
Group Key Update Interval
, enter the amount of time before the group key used for broadcast and multicast
data is changed.
6. Next to the
Pre-Shared Key section
, enter a key in the Passphrase field. The key is entered as a passphrase in ASCII
format at both ends of the wireless connection. The passphrase must be between 8-63 characters.
7. Click
Save Settings
at the top of the window to save your settings. If you are configuring the access point with a
wireless adapter, you will lose connectivity until you enable WPA-PSK on your adapter and enter the same passphrase
as you did on the access point.
Page 80 / 100
80
D-Link DAP-1522 User Manual
Section 5 - Connecting to a Wireless Network
Connect to a Wireless Network
Using Windows
®
XP
Windows
®
XP users may use the built-in wireless utility (Zero Configuration Utility). The following instructions are for
Service Pack 2 users.
If you are using another company’s utility or Windows
®
2000, please refer to the user manual
of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option
similar to the Windows
®
XP utility as seen below.
Right-click on the wireless computer icon in your system tray
(lower-right corner next to the time). Select
View Available
Wireless Networks
.
If you receive the
Wireless Networks Detected
bubble, click
on the center of the bubble to access the utility.
or
The utility will display any available wireless networks in your
area. Click on a network (displayed using the SSID) and click
the
Connect
button.
If you get a good signal, but cannot access the Internet,
check you TCP/IP settings for your wireless adapter. Refer
to the
Networking Basics
section in this manual for more
information.

Rate

4.3 / 5 based on 4 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top