86

D-Link DAP-1522 User Manual

Section 5 - Connecting to a Wireless Network

Click

Connect Anyway

to continue.

The utility will display the following window to indicate a

connection is being made.

The final window indicates the establishment of a successful

connection.

The next two pages display the windows used to connect to

either a WEP or a WPA-PSK wireless network.

87

D-Link DAP-1522 User Manual

Section 5 - Connecting to a Wireless Network

Click on a network (displayed using the SSID) using WEP

under Select a network to connect to and then click the

Connect

button.

Enter the appropriate security key or passphrase in the field

provided and then click the

Connect

button.

Configure WEP

It is recommended to enable WEP on your wireless bridge or access point before configuring your wireless adapter.

If you are joining an existing network, you will need to know the WEP key being used.

88

D-Link DAP-1522 User Manual

Section 5 - Connecting to a Wireless Network

Click on a network (displayed using the SSID) using WPA-PSK

under Select a network to connect to and then click the

Connect

button.

Enter the appropriate security key or passphrase in the field

provided and then click the

Connect

button.

Configure WPA-PSK

It is recommended to enable WEP on your wireless bridge or access point before configuring your wireless adapter.

If you are joining an existing network, you will need to know the WEP key being used.

89

D-Link DAP-1522 User Manual

Section 6 - Troubleshooting

Troubleshooting

This chapter provides solutions to problems that can occur during the installation and operation of the DAP-1522.

Read the following descriptions if you are having problems.

(The examples below are illustrated in Windows

®

XP.

If

you have a different operating system, the screenshots on your computer will look similar to the following examples.)

1. Why can’t I access the web-based configuration utility?

When entering the IP address of the D-Link access point (192.168.0.50 for example), you are not connecting to a

website on the Internet or have to be connected to the Internet. The device has the utility built-in to a ROM chip in the

device itself. Your computer must be on the same IP subnet to connect to the web-based utility.

• Make sure you have an updated Java-enabled web browser. We recommend the following:

• Internet Explorer 7.0 or higher

• Firefox 3.0 or higher

• Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using

a different cable or connect to a different port on the device if possible. If the computer is turned off, the link light may

not be on.

• Disable any internet security software running on the computer. Software firewalls such as Zone Alarm, Black Ice,

Sygate, Norton Personal Firewall, and Windows

®

XP firewall may block access to the configuration pages. Check the

help files included with your firewall software for more information on disabling or configuring it.

90

D-Link DAP-1522 User Manual

Section 6 - Troubleshooting

• Configure your Internet settings:

• Go to

Start > Settings > Control Panel

. Double-click the

Internet Options

Icon. From the Security tab,

click the button to restore the settings to their defaults.

• Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings

button. Make sure nothing is checked. Click OK.

• Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three

times.

• Close your web browser (if open) and open it.

• Access the web management. Open your web browser and enter the IP address of your D-Link access point in the

address bar. This should open the login page for your the web management.

• If you still cannot access the configuration, unplug the power to the access point for 10 seconds and plug back in.

Wait about 30 seconds and try accessing the configuration. If you have multiple computers, try connecting using a

different computer.

2. What can I do if I forgot my password?

If you forgot your password, you must reset your access point. Unfortunately this process will change all your settings

back to the factory defaults.

To reset the access point, locate the reset button (hole) on the rear panel of the unit. With the access point powered

on, use a paperclip to hold the button down for 10 seconds. Release the button and the access point will go through

its reboot process. Wait about 30 seconds to access the access point. The default IP address is 192.168.0.50. When

logging in, the username is admin and leave the password box empty.