61

D-Link DAP-1522 User Manual

Section 3 - Configuration

Transmit Power:

RTS Threshold:

Fragmentation

Threshold:

Short GI:

Set the transmit power of the antennas.

This value should remain at its default setting of

2436. If inconsistent data flow is a problem, only a

minor modification should be made.

The fragmentation threshold, which is specified

in bytes, determines whether packets will be

fragmented. Packets exceeding the 2346 byte

setting will be fragmented before transmission.

2346 is the default setting.

Check this box to reduce the guard interval time

therefore increasing the data capacity. However,

it is less reliable and may create higher data loss.

Advanced

Advanced Wireless

62

D-Link DAP-1522 User Manual

Section 3 - Configuration

Enable QoS:

QoS Type:

Priority by LAN

Port:

Enable this option if you want QoS to prioritize

your traffic.

There are two options available for your special

application: (1) Priority by LAN Port, and (2) Priority

by Protocol.

There are four priority levels for all LAN ports. The

priority level values assigned are 1 for Background,

3 for Best Effort, 5 for Video, and 7 for Voice (Voice

is the highest level and Background is the lowest

level) at a normal priority.

QoS

The Quality of Service (QoS) feature regulates the flow of data through the access point by assigning a priority to

each packet.

It enhances your experience of wireless network usage by prioritizing the traffic of different applications.

Enabling this option allows the AP to prioritize traffic. There are two options available for the special application.

63

D-Link DAP-1522 User Manual

Section 3 - Configuration

Priority by

Protocol:

Wireless to

Ethernet:

Ethernet to

Wireless:

ACK/DHCP/ICMP/

DNS Priority:

Web Traffic

Priority:

Mail Traffic

Priority:

Ftp Traffic Priority:

Other Traffic

Priority:

Users can set the priority and percentage of total bandwidth

reserved for each of their four traffic categories. Please

note that the combined percentage value of transmission

limits does not have to be 100%. These percentages

represent the maximum bandwidth designated for each

traffic category.

The value entered here indicates the wireless to Ethernet

speed required before the Advanced QoS function is

enabled. Advanced QoS will be enabled once the total

bandwidth reaches or surpasses the set value. The

suggested range is 800 ~ 96000kbits/sec.

The value entered here indicates the Ethernet to wireless

speed required before the Advanced QoS function is

enabled. Advanced QoS will be enabled once the total

bandwidth reaches or surpasses the set value. The

suggested range is 800 ~ 96000kbits/sec.

Represents the priority value and bandwidth limit applied to ACK, DHCP, ICMP, and DNS for packet delivering.

Traffic generated by typical Web services (packets sent through ports 80,443, 3128 and 8080).

Traffic generated by e-mail sending and receiving (ports 25, 110, 465 and 995).

Traffic generated by FTP Uploading and Downloading (ports 20, 21).

Other traffic generated that does not regard the aforementioned packet delivery.

Note:

Normally the wireless connection transmits application data packets based on the wireless to Ethernet speed and Ethernet to wireless speed.

Users can treat the two speeds as system transmission bandwidth, where all applications will share the whole system bandwidth based on assigned

priorities. Note that the maximum amount of bandwidth that can be used is the same as the set value of both speeds.

64

D-Link DAP-1522 User Manual

Section 3 - Configuration

Enter a name for your new schedule.

Select a day, a range of days, or All Week to

include every day.

Check

All Days

or enter a start and end time for

your schedule.

Select

On

or

Off

from the drop-down menu.

Click

Add

to save your schedule. You must click

Save Settings

at the top for your schedules to

go into effect.

The list of schedules will be listed here. Click the

Edit

icon to make changes or click the

Delete

icon to remove the schedule.

Name:

Days:

Time:

Wireless:

Add:

Schedule Rules

List:

Schedule

65

D-Link DAP-1522 User Manual

Section 3 - Configuration

Password:

Verify

Password:

Enter a new password for the Administrator Login

Name. The administrator can make changes to the

settings.

Enter the same password that you entered in the

previous textbox in order to confirm its accuracy.

Tools

Admin

This page will allow you to change the Administrator password. Admin has read/write access.