Billion BiPAC 7300W Router Manual PDF (Setup & Configuration Guide)

Page 121 / 139 Scroll up to view Page 116 - 120

118

5.3.9.1 Static Route

Destination:

The destination subnet IP address.

Netmask:

Subnet mask of the destination IP addresses based on above destination.

Gateway:

The gateway IP address to which packets are forwarded.

Interface:

Select the interface through which packets are forwarded.

Cost:

Represents the cost of transmission for routing purposes. The number need not be

precise, but it must be between 0 and 65535.

5.3.9.2 Static ARP

This feature allows you to map the layer-2 MAC (Media Access Control) address that

corresponds to the layer-3 IP address of the device.

IP Address:

Enter the IP of the device that the corresponding MAC address will be mapped

to.

MAC Address:

Enter the MAC address that corresponds to the IP address of the device.

Click Add to confirm the settings.

Page 122 / 139

119

Edit:

Check the Edit radio button to display the parameter of the selected application, then

after changing the parameters click the "Edit/Delete" button to apply the changes.

Delete:

To remove a static ARP entry, check the Delete box of the selected entry then click

the "Edit/Delete" button.

5.3.9.3 Dynamic DNS

The Dynamic DNS function lets you alias a dynamic IP address to a static hostname, so if

your ISP does not assign you a static IP address you can still use a domain name. This is

especially useful for hosting servers via your ADSL connection, so that anyone wishing to

connect to you may use your domain name, rather than having to use your dynamic IP

address, which changes from time to time. This dynamic IP address is the WAN IP address

of the router, which is assigned to you by your ISP.

You first need to register and establish an account with the Dynamic DNS provider using

their web site, for example

http://www.dyndns.org/

Disable:

Check to disable the Dynamic DNS function.

Enable:

Check to enable the Dynamic DNS function. The fields following are activated

and required.

Dynamic DNS Server:

Select the DDNS service you have established an account with.

Wildcard:

Select this check box to enable the DYNDNS Wildcard.

Page 123 / 139

120

Domain Name, Username and Password:

Enter your registered domain name and

your username and password for this service.

Period:

Set the time period between updates, for the Router to exchange information

with the DDNS server. In addition to updating periodically as per your settings, the router will

perform an update when your dynamic IP address changes. If the period is 0, the router will

check the DNS server every 5 min.

5.3.9.4 VLAN

VLAN (Virtual Local Area Network) is a group of devices on different physical LAN segments

that can communicate with each other as if they were all on the same physical LAN

segment.

Page 124 / 139

121

5.3.9.5 Device Management

The Device Management advanced configuration settings allow you to control your router’s

security options and device monitoring features.

Embedded Web Server:

HTTP Port:

The port number of the router’s embedded web server (for web-based

configuration uses. The default value is the standard HTTP port, 80. You may specify an

alternative if, for example, you are running a web server on a PC within your LAN.

For Example:

User A changes HTTP port number to

100

, specifies their own IP address of

192.168.1.55

, and sets the logout time to be

100

minutes. The router only allows User A

access from the IP address

192.168.1.55

to logon to the Web GUI by typing:

http://192.168.1.254:100

in their web browser. After 100 minutes, the device automatically

logs out User A.

Universal Plug and Play (UPnP):

UPnP offers peer-to-peer network connectivity for PCs and other network devices, along

with control and data transfer between devices. UPnP offers many advantages for users

running NAT routers through UPnP NAT Traversal, and on supported systems makes tasks

such as port forwarding much easier by letting the application control the required settings,

removing the need for the user to control advanced configuration of their device.

Both the user’s Operating System and the relevant application must support UPnP in

addition to the router. Windows XP and Windows Me natively support UPnP (when the

component is installed), and Windows 98 users may install the Internet Connection Sharing

client from Windows XP in order to support UPnP. Windows 2000 does not support UPnP.

Page 125 / 139

122

Disable:

Check to disable the router’s UPnP functionality.

Enable:

Check to enable the router’s UPnP functionality.

UPnP Port:

The Default setting is 2800. It is highly recommended you use this port value.

If this value conflicts with other ports already in use you may wish to change the port.

Installing UPnP in Windows Example

Follow the steps below to install the UPnP in Windows Me.

Step 1:

Click Start and Control Panel. Double-click Add/Remove Programs.

Step 2:

Click on the Windows Setup tab and select Communication in the Components

selection box. Click Details.

Rate

Popular Billion Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share