1. Home
    2. /
  2. Manuals
    3. /
  3. Arris
    4. /
  4. TG862A
    5. /
  5. 9
Page 41 / 52 Scroll up to view Page 36 - 40
Cable Modem Start Up Sequence
DS
US
Online
Description
Flash
Off
Off
Downstream search
On
Flash
Off
Downstream found; upstream search
On
On
Flash
Downstream and Upstream found;
retrieving setup information from
cable operator
On
On
On
Ready for service
Touchstone TG862 Telephony Gateway User’s Guide
Safety
Getting
Started
Installation
Ethernet
Configuration
Usage
Troubleshooting
Glossary
41
Page 42 / 52
Using the Reset Button
Use the
Reset
button, on the back of the Telephony Gateway, to reset the modem
and perform initialization as if you power cycled the unit. You may need to reset the
Telephony Gateway if you are having problems connecting to the Internet. Using
this button will be rare.
Use a pointed
non-metallic
object to press this button. The photo to the left shows
the location of the
Reset
button. The
Reset
button is recessed to prevent acci-
dental resets.
The diagram on the left shows the location of the reset button.
TG862S Only:
The rear panel power switch can
also be used to power cycle the
unit.
Resetting the Router to Factory Defaults
To reset the router to factory defaults, press and hold the
Reset
button on the back
of the Telephony Gateway for more than fifteen seconds. This restores the wireless
setup configuration and router configuration parameters to the factory defaults. You
may need to do this if a misconfiguration has locked out all access.
Touchstone TG862 Telephony Gateway User’s Guide
Safety
Getting
Started
Installation
Ethernet
Configuration
Usage
Troubleshooting
Glossary
42
Reset
USB
Telephone
Ethernet
10/100/1000
Cable
1/2
2
2
1
4
3
TG862A
Reset
USB
Telephone
Ethernet
10/100/1000
Cable
1/2
2
2
1
4
3
TG862S
Reset
Button
Power
Switch
Page 43 / 52
Troubleshooting
The Telephony Gateway is plugged in, but the Power light is off.
Check all power connections. Is the power cord plugged in firmly at both
ends?
If you plugged the power cord into a power strip, make sure the strip is
switched on.
Avoid using an outlet controlled by a wall switch, if possible.
Finally, check the fuse or circuit breaker panel.
I’m not getting on the Internet (all connections).
It may take over 30 minutes to establish a connection the first time you
power up your Telephony Gateway, especially when many people are online.
Always leave your Telephony Gateway plugged into AC power and connected
to the cable system.
Check the front panel lights:
•
The
Power
and
Online
lights should be on.
•
If the
Power
light blinks for more than 30 minutes, call your cable
company for assistance.
Check your cable connections. Connectors should be tight. The
coax cable
should not be pinched, kinked, or bent sharply—any of these can cause a
break or short in the cable (you may have to replace the cable). If you have
one or more splitters between the Telephony Gateway and CATV outlet, re-
move the splitters and connect the Telephony Gateway directly to the out-
let.
Proceed to the Ethernet or wireless solutions (next page) if necessary.
Touchstone TG862 Telephony Gateway User’s Guide
Safety
Getting
Started
Installation
Ethernet
Configuration
Usage
Troubleshooting
Glossary
43
Page 44 / 52
I’m not getting on the Internet. (Ethernet)
If you are using a hub, is the hub turned on?
Are you using the right type of
Ethernet
cable? Use the supplied cable for di-
rect connection to a computer; use a cross-over cable for connection to a
hub.
Press the
Reset
button on the back of the Telephony Gateway.
A misconfiguration could lock out all access to the Telephony Gateway router.
If you think this has happened, see
Resetting the Router to Factory Defaults
.
I’m not getting on the Internet. (Wireless)
Check the indicator lights (see
Using the Telephony Gateway
) — the WiFi
light should be on.
Does your connection utility discover your wireless LAN? If you turned off
“Broadcast SSID” you need to manually enter the name of your wireless LAN
in the connection utility.
Change your security mode to “WEP” or “disabled”. If you use “disabled,”
enable one of the other security modes as soon as you find the problem.
A misconfiguration could lock out all access to the Telephony Gateway router.
If you think this has happened, see
Resetting the Router to Factory Defaults
.
My wireless Internet connection stops working sometimes.
This is usually caused by interference — two common sources are 2.4GHz
“remote” telephones and microwave ovens. If you cannot remove the inter-
fering product, try using a different channel or setting Protected Mode.
I can get on the Internet, but everything is slow.
If the Web site you are visiting is very popular, that site may be having trou-
ble servicing all the requests. If other sites download quickly, wait for a few
minutes and try again. Usage during peak hours may also affect the connec-
tion speed.
Other communications on the LAN, or interference with wireless connec-
tions, may slow down your connection.
Touchstone TG862 Telephony Gateway User’s Guide
Safety
Getting
Started
Installation
Ethernet
Configuration
Usage
Troubleshooting
Glossary
44
Page 45 / 52
I don’t have dial tone when I pick up my phone, why?
In order for telephone service to be functional on the Telephony Gateway,
telephone service must have been purchased from the service provider and
configured on your Telephony Gateway. The following steps should help in
identifying the source of the problem.
1
Is the Power LED lit?
•
If not, check to make sure the Telephony Gateway is plugged in
and the outlet has power.
•
If the LED is lit, go to the next step.
2
Is the Online LED lit?
•
If not, check the coax connection at the Telephony Gateway and
the wall. Ensure they are connected and tight. If they are and
you do not have dial tone, contact your service provider.
•
If the Online LED is lit, go to the next step.
3
Is the Telephone (Tele 1 or Tel 2) LED lit?
•
If not, phone service has not been set up on that line. Contact
your service provider.
•
If it is blinking, there is a phone off hook somewhere in the
house. Find that phone and hang it up.
•
If it is lit, go to the next step.
4
Is the phone plugged directly into the Telephony Gateway?
•
Make sure the phone is plugged into the port on the back of the
Telephony Gateway labeled “Telephone 1/2” for line 1, and “Tele-
phone 2” for line 2.
•
If so, try a different phone. Make sure the new phone is a work-
ing phone.
•
If a known good phone is used and you still don’t have dial tone,
try a different phone cable. If a new phone and cable do not re-
store dial tone, call your service provider.
Touchstone TG862 Telephony Gateway User’s Guide
Safety
Getting
Started
Installation
Ethernet
Configuration
Usage
Troubleshooting
Glossary
45

Rate

4 / 5 based on 2 votes.

Popular Arris Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top