Chapter 2 - CPE Installation

BreezeMAX Si 4000 Hardware Description

BreezeMAX Si 4000 CPE

22

Operator Manual

2.3.3

Reset Button

The recessed button is used to reset the BreezeMAX Si 4000 or to restore the unit

to factory default configuration.



Do not perform reset to factory default unless specifically instructed by

customer support.



To perform a hardware reset, press the button for approximately 1 second.



To restore the device to the factory default settings, press and hold the button

for 5 seconds or more; any configuration changes you made are removed and

the factory default configuration is restored to the unit.



Some user-configured parameters will be lost and must be reconfigured.

2.3.4

WiMAX Antennas

Two built-in omnidirectional antennas are included with the BreezeMAX Si 4000

for WiMAX communications. The omnidirectional antennas transmit and receive

signals in all directions equally.

2.3.5

BreezeMAX Si 4000Cables

Use only Category 5E Ethernet cables from either Alvarion or any of the approved

manufacturers, listed in

Table 2-4

. Consult with Alvarion's specialists on the

suitability of other cables.

NOTE

The length of the Ethernet cable connecting the BreezeMAX Si 4000 to the data equipment, must

not exceed 100 meters.

Table 2-4: Approved Category 5E Ethernet Cables

Manufacturer

Part Number

Superior Cables Ltd.

www.superior-cables.com

612098

HES Cabling Systems

www.hescs.com

H5E-00481

Teldor

www.teldor.com

8393204101

Chapter 2 - CPE Installation

BreezeMAX Si 4000 Hardware Description

BreezeMAX Si 4000 CPE

23

Operator Manual

In case of missing information in the manufacturer's WEB site (product

specifications, ordering issues, etc.), it is highly recommended to contact the

manufacturer's sales representative directly.

2.3.6

BreezeMAX Si 4000Wi-Fi Option

The BreezeMAX Si 40003.5 GHz model includes the 802.11b/g Wi-Fi option. This

unit includes internal antennas for local wireless connections to PCs.

To connect your PC using WiFi, click the WiFi icon

(lower right corner of PC);

Click Find WLAN and select the name of WiFi network Click Connect.

Southbay Holdings Limited

11th Fl., 15, Lane 347, Jong Jeng Rd.

Shin Juang City, Taipei County

Taiwan, R.O.C.

Attn: Eva Lin

Tel. 886-2-2832 3339

Fax. 886-2-2206 0081

E-mail:

TSM2404A0D

GU-Tech., LLC . -

A Member of OVIS GroupTel/Fax :

732 918 8221 Mobile:

718 909 4093

www.OVIS.COM.TW

www.GU-TECH.COM

Table 2-4: Approved Category 5E Ethernet Cables

Manufacturer

Part Number

3

Chapter

Commissioning

zzAlvarion_ page

Chapter 3 - Commissioning

BreezeMAX Si 4000 CPE

25

Operator Manual

In This Chapter:



“Introduction” on page 26



“Configuring the CPE Using the Web Management Interface” on page 28



“Configuring the CPE Using the WiMAX Modem Application CD” on page 31



“Configuring the CPE Using the IPKG Upgrade” on page 35



“Creating a Default Configuration File” on page 36



“Operation Verification” on page 39

Chapter 3 - Commissioning

Introduction

BreezeMAX Si 4000 CPE

26

Operator Manual

3.1

Introduction

After completing the installation process, as described in the preceding chapter,

several actions should be performed to ensure connectivity with a base station

(BS) and provisioning of services. After the subscriber unit is connected with a BS,

it can be fully managed via the wireless link:

1

The basic parameters must be configured to ensure that the unit operates

correctly and can communicate with a BS.

2

Proper operation should be verified, including data connectivity.

3

The unit must be positioned correctly to ensure optimal performance of the

wireless link.

The following methods are available for configuring the BreezeMAX Si 4000:



The web-based management interface - accessed using a PC/Notebook with a

web browser (see

“Configuring the CPE Using the Web Management Interface”

on page 28

).



An automatic configuration tool provided on a CDROM for the subscribers (see

“Configuring the CPE Using the WiMAX Modem Application CD” on page 31

).



Upgrading the CPE using an auto-configuration file, or IPKG (in

*.ipk

format)

(see

“Configuring the CPE Using the IPKG Upgrade” on page 35

).

The device may be delivered with the operator’s default settings already configured

in the FLASH memory.

The following parameters must be configured in order for a link to be established.

Table 3-1: Basic Parameters

Item

Default Value

Comment

User Name (WiMAX)

WAN mac address and

WiMax.com realm, e.g:

Should be supplied by system

administrator. Configured in the

Internet> Security> Authentication

window

WiMAX Password

quickynikynyoky

Domain

wimax.com (also Eng > WiMAX

Config > Realm

Frequency

Should be supplied by system

administrator.