Page 71 / 152 Scroll up to view Page 66 - 70
69
8 Wireless LAN Configurations
If your computer, PDA, game console, or other network device is equipped
with wireless network interface, you can use the wireless function of the
X650 to connect them to Internet and share resources with other computers
that have a wired-LAN connection. You can also use the built-in security
functions to protect your network from being invaded by malicious
intruders.
This router supports both 2.4GHz and 5GHz wireless bands simultaneously;
the wireless settings for both wireless bands are almost the same. The
following sections will highlight the differences between these two selections.
Go to ‘General Setup’ page and select ‘2.4GHz Wireless’ or ‘5GHz Wireless’
to configure the wireless settings for the different wireless radio types.
Please follow these instructions to set wireless parameters:
Please click ‘2.4GHz Wireless’ or ‘5GHz Wireless’ menu on the left of the web
management interface and the following message will be displayed on your
web browser. You must enable wireless function of this router, or the wireless
interface of this router will not function. Please select ‘Enable’ (1), then click
‘Apply’ (2) button.
If you want to disable wireless function, please switch hardware button to
Page 72 / 152
70
turn off wireless radio at rear panel of device.
After you click ‘Apply’(2), the following message will be displayed on your
web browser:
Please click ‘Continue’ to return to the previous setup menu and continue with
other setup procedures, or click ‘Apply’ to reboot the router so the settings take
effect (Please wait about 40 seconds for router to reboot).
8.1 Basic Wireless Settings
Please click ‘2.4GHz Wireless’ or ‘5GHz Wireless’ menu on the left of the web
management interface, then click ‘Basic Settings’, and the following message
will be displayed on your web browser:
2.4GHz Wireless
1
2
Page 73 / 152
71
5GHz Wireless
The X650 can work in 6 different modes:
1)
Access Point
: Standard wireless AP .
2)
Station-Infrastructure
: Configure the X650 to work with an Ethernet device
(such as a TV, Game player, HDD&DVD) to enable the Ethernet device to be a
wireless station.
3)
AP Bridge-Point to Point
: Connect the X650 with another wireless router to
expand the scope of your network.
4)
AP Bridge-Point to Multi-Point
: Connect the X650 with up to four other
wireless routers to expand the scope of your network.
Page 74 / 152
72
5)
AP Bridge-WDS
: Connect the X650 with up to four WDS-capable wireless
routers to expand the scope of your network.
6)
Universal Repeater
: The X650 can act as Station and AP at the same time. It
can use its Station function to connect to a Root AP and use its AP function to
service all wireless stations within its coverage.
Please select a proper operation mode you want to use from ‘Mode’ dropdown
menu (1), and continue on with other operation mode specific settings:
Access Point
- Please go to section 8.1.1
Station-Infrastructure
- Please go to section 8.1.2
AP Bridge-Point to Point
- Please go to section 8.1.3
AP Bridge-Point to Multi-Point
- Please go to section 8.1.4
AP Bridge-WDS
- Please go to section 8.1.5
Universal Repeater
- Please go to section 8.1.6
8.1.1 Setup procedure for ‘Access Point’:
Please select the radio band you want to use from the ‘Band’ dropdown menu
(2), and the following message will be displayed:
2.4GHz Access Point Settings
NOTE: For ‘AP Bridge-Point to Point’ and ‘AP Bridge-Point to
Multi-Point’ mode, wireless router is operated in wireless bridge
dedicated mode –
this means that the X650 is only being used to
expand the scope of network and no wireless clients will be accepted.
If you want to use your wireless router to expand the scope of
network and also accept wireless clients, please select ‘AP
Bridge-WDS’ or ‘Universal Repeater‘ mode.
Page 75 / 152
73
5GHz Access Point Settings
Here are descriptions of each setup item:
Band (2):
Please select the radio band from one of following
options:
2.4GHz Band
2.4 GHz (B): this mode only allows 802.11b wireless
network clients to connect to X650 (maximum transfer
rate 11Mbps).
2.4 GHz (N): this mode only allows 802.11n wireless
network clients to connect to X650 (maximum transfer
rate 300Mbps).
1
2
3
4
5
1
2
3
4
5

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top