Page 341 / 421
Scroll up to view Page 336 - 340
Appendix A Setting up Your Computer’s IP Address
P-660HN-FxZ Series User’s Guide
338
Figure 215
Red Hat 9.0: Dynamic IP Address Setting in ifconfig-eth0
•
If you have a static IP address, enter
static
in the
BOOTPROTO=
field. Type
IPADDR
= followed by the IP address (in dotted decimal notation) and type
NETMASK
=
followed by the subnet mask. The following example shows an example where the
static IP address is
192.168.1.10 and the subnet mask is 255.255.255.0.
Figure 216
Red Hat 9.0: Static IP Address Setting in ifconfig-eth0
2
If you know your DNS server IP address(es), enter the DNS server information in the
resolv.conf
file in the
/etc
directory.
The following figure shows an example
where two DNS server IP addresses are specified.
Figure 217
Red Hat 9.0: DNS Settings in resolv.conf
3
After you edit and save the configuration files, you must restart the network card. Enter
./network restart
in the
/etc/rc.d/init.d
directory.
The following figure
shows an example.
Figure 218
Red Hat 9.0: Restart Ethernet Card
DEVICE=eth0
ONBOOT=yes
BOOTPROTO=dhcp
USERCTL=no
PEERDNS=yes
TYPE=Ethernet
DEVICE=eth0
ONBOOT=yes
BOOTPROTO=static
IPADDR=
192.168.1.10
NETMASK=
255.255.255.0
USERCTL=no
PEERDNS=yes
TYPE=Ethernet
nameserver 172.23.5.1
nameserver 172.23.5.2
[root@localhost init.d]# network restart
Shutting down interface eth0:
[OK]
Shutting down loopback interface:
[OK]
Setting network parameters:
[OK]
Bringing up loopback interface:
[OK]
Bringing up interface eth0:
[OK]
Page 342 / 421
Appendix A Setting up Your Computer’s IP Address
P-660HN-FxZ Series User’s Guide
339
Verifying Settings
Enter
ifconfig
in a terminal screen to check your TCP/IP properties.
Figure 219
Red Hat 9.0: Checking TCP/IP Properties
[root@localhost]# ifconfig
eth0
Link encap:Ethernet
HWaddr 00:50:BA:72:5B:44
inet addr:172.23.19.129
Bcast:172.23.19.255
Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST
MTU:1500
Metric:1
RX packets:717 errors:0 dropped:0 overruns:0 frame:0
TX packets:13 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:730412 (713.2 Kb)
TX bytes:1570 (1.5 Kb)
Interrupt:10 Base address:0x1000
[root@localhost]#
Page 343 / 421
Appendix A Setting up Your Computer’s IP Address
P-660HN-FxZ Series User’s Guide
340
Page 344 / 421
P-660HN-FxZ Series User’s Guide
341
A
PPENDIX
B
Pop-up Windows, JavaScript
and Java Permissions
In order to use the web configurator you need to allow:
•
Web browser pop-up windows from your device.
•
JavaScript (enabled by default).
•
Java permissions (enabled by default).
"
Internet Explorer 6 screens are used here. Screens for other Internet Explorer
versions may vary.
Internet Explorer Pop-up Blockers
You may have to disable pop-up blocking to log into your device.
Either disable pop-up blocking (enabled by default in Windows XP SP (Service Pack) 2) or
allow pop-up blocking and create an exception for your device’s IP address.
Disable Pop-up Blockers
1
In Internet Explorer, select
Tools
,
Pop-up Blocker
and then select
Turn Off Pop-up
Blocker
.
Figure 220
Pop-up Blocker
You can also check if pop-up blocking is disabled in the
Pop-up Blocker
section in the
Privacy
tab.
1
In Internet Explorer, select
Tools
,
Internet Options
,
Privacy
.
Page 345 / 421
Appendix B Pop-up Windows, JavaScript and Java Permissions
P-660HN-FxZ Series User’s Guide
342
2
Clear the
Block pop-ups
check box in the
Pop-up Blocker
section of the screen. This
disables any web pop-up blockers you may have enabled.
Figure 221
Internet Options: Privacy
3
Click
Apply
to save this setting.
Enable Pop-up Blockers with Exceptions
Alternatively, if you only want to allow pop-up windows from your device, see the following
steps.
1
In Internet Explorer, select
Tools
,
Internet Options
and then the
Privacy
tab.
2
Select
Settings…
to open the
Pop-up Blocker Settings
screen.
19216811.live