1. Home
    2. /
  2. Manuals
    3. /
  3. Zyxel
    4. /
  4. P-2602HW-D1A
    5. /
  5. 34
Page 166 / 427 Scroll up to view Page 161 - 165
P-2602H(W)(L)-DxA Series User’s Guide
166
Chapter 11 Voice
11.14
Advanced Analog Phone Setup Screen
Use this screen to edit advanced settings for each phone port. To access this screen, click
Advanced Setup
in
VoIP > Phone > Analog Phone
.
Figure 92
Phone > Analog Phone > Advanced
Each field is described in the following table.
Apply
Click this to save your changes and to apply them to the ZyXEL Device.
Cancel
Click this to set every field in this screen to its last-saved value.
Advanced Setup
Click this to edit the advanced settings for this phone port. The
Advanced Analog
Phone Setup
screen appears.
Table 57
Phone > Analog Phone
LABEL
DESCRIPTION
Table 58
Phone > Analog Phone > Advanced
LABEL
DESCRIPTION
Analog Phone
This field displays the phone port you see in this screen.
Voice Volume
Control
Speaking Volume
Enter the loudness that the ZyXEL Device uses for speech that it sends to the peer
device. -1 is the quietest, and 1 is the loudest.
Listening Volume
Enter the loudness that the ZyXEL Device uses for speech that it receives from the
peer device. -1 is the quietest, and 1 is the loudest.
Echo Cancellation
G.168 Active
Select this if you want to eliminate the echo caused by the sound of your voice
reverberating in the telephone receiver while you talk.
Page 167 / 427
P-2602H(W)(L)-DxA Series User’s Guide
Chapter 11 Voice
167
11.14.1
Common Phone Settings Screen
Use this screen to activate and deactivate immediate dialing. To access this screen, click
VoIP
> Phone > Common
.
Figure 93
Phone > Common
Each field is described in the following table.
Dialing Interval
Select
Dialing Interval
Select
Enter the number of seconds the ZyXEL Device should wait after you stop dialing
numbers before it makes the phone call. The value depends on how quickly you
dial phone numbers.
If you select
Active Immediate Dial
in
VoIP > Phone > Common
, you can press
the pound key (#) to tell the ZyXEL Device to make the phone call immediately,
regardless of this setting.
VAD Support
Select this if the ZyXEL Device should stop transmitting when you are not
speaking. This reduces the bandwidth the ZyXEL Device uses.
Back
Click this to return to the
Analog Phone
screen without saving your changes.
Apply
Click this to save your changes and to apply them to the ZyXEL Device.
Cancel
Click this to set every field in this screen to its last-saved value.
Table 58
Phone > Analog Phone > Advanced
LABEL
DESCRIPTION
Table 59
Phone > Common
LABEL
DESCRIPTION
Active Immediate
Dial
Select this if you want to use the pound key (#) to tell the ZyXEL Device to make
the phone call immediately, instead of waiting the number of seconds you selected
in the
Dialing Interval Select
in
VoIP > Phone > Analog Phone
.
If you select this, dial the phone number, and then press the pound key. The
ZyXEL Device makes the call immediately, instead of waiting. You can still wait, if
you want.
Apply
Click this to save your changes and to apply them to the ZyXEL Device.
Cancel
Click this to set every field in this screen to its last-saved value.
Page 168 / 427
P-2602H(W)(L)-DxA Series User’s Guide
168
Chapter 11 Voice
11.15
Supplementary Phone Services Overview
Supplementary services such as call hold, call waiting, call transfer, … are generally available
from your VoIP service provider. The ZyXEL Device supports the following services:
•
Call Hold
•
Call Waiting
•
Making a Second Call
•
Call Transfer
•
Call Forwarding (see
Section 11.19 on page 174
)
•
Three-Way Conference
•
Internal Calls (see
Section 12.3 on page 179
)
Note:
To take full advantage of the supplementary phone services available through
the ZyXEL Device's phone ports, you may need to subscribe to the services from your
VoIP service provider.
11.15.1
The Flash Key
Flashing means to press the hook for a short period of time (a few hundred milliseconds)
before releasing it. On newer telephones, there should be a "flash" key (button) that generates
the signal electronically.
If the flash key is not available, you can tap (press and immediately
release) the hook by hand to achieve the same effect.
However, using the flash key is
preferred since the timing is much more precise. With manual tapping, if the duration is too
long, it may be interpreted as hanging up by the ZyXEL Device.
You can invoke all the supplementary services by using the flash key.
11.15.2
Europe Type Supplementary Phone Services
This section describes how to use supplementary phone services with the
Europe Type
Call
Service Mode
. Commands for supplementary services are listed in the table below.
After pressing the flash key, if you do not issue the sub-command before the default sub-
command timeout (2 seconds) expires or issue an invalid sub-command, the current operation
will be aborted.
Table 60
European Flash Key Commands
COMMAND
SUB-COMMAND
DESCRIPTION
Flash
Put a current call on hold to place a second call.
Switch back to the call (if there is no second call).
Flash
0
Drop the call presently on hold or reject an incoming call which is
waiting for answer.
Flash
1
Disconnect the current phone connection and answer the incoming
call or resume with caller presently on hold.
Page 169 / 427
P-2602H(W)(L)-DxA Series User’s Guide
Chapter 11 Voice
169
11.15.2.1
European Call Hold
Call hold allows you to put a call (
A
) on hold by pressing the flash key.
If you have another call, press the flash key and then “2” to switch back and forth between
caller
A
and
B
by putting either one on hold.
Press the flash key and then “0” to disconnect the call presently on hold and keep the current
call on line.
Press the flash key and then “1” to disconnect the current call and resume the call on hold.
If you hang up the phone but a caller is still on hold, there will be a remind ring.
11.15.2.2
European Call Waiting
This allows you to place a call on hold while you answer another incoming call on the same
telephone (directory) number.
If there is a second call to a telephone number, you will hear a call waiting tone. Take one of
the following actions.
•
Reject the second call.
Press the flash key and then press “0”.
•
Disconnect the first call and answer the second call.
Either press the flash key and press “1”, or just hang up the phone and then answer the
phone after it rings.
•
Put the first call on hold and answer the second call.
Press the flash key and then “2”.
11.15.2.3
European Call Transfer
Do the following to transfer an incoming call (that you have answered) to another phone.
1
Press the flash key to put the caller on hold.
Flash
2
1. Switch back and forth between two calls.
2. Put a current call on hold to answer an incoming call.
3. Separate the current three-way conference call into two
individual calls (one is on-line, the other is on hold).
Flash
3
Create three-way conference connection.
Flash
*98#
Transfer the call to another phone.
Table 60
European Flash Key Commands
COMMAND
SUB-COMMAND
DESCRIPTION
Page 170 / 427
P-2602H(W)(L)-DxA Series User’s Guide
170
Chapter 11 Voice
2
When you hear the dial tone, dial “*98#” followed by the number to which you want to
transfer the call. to operate the Intercom.
3
After you hear the ring signal or the second party answers it, hang up the phone.
11.15.2.4
European Three-Way Conference
Use the following steps to make three-way conference calls.
1
When you are on the phone talking to someone, press the flash key to put the caller on
hold and get a dial tone.
2
Dial a phone number directly to make another call.
3
When the second call is answered, press the flash key and press “3” to create a three-way
conversation.
4
Hang up the phone to drop the connection.
5
If you want to separate the activated three-way conference into two individual
connections (one is on-line, the other is on hold), press the flash key and press “2”.
11.15.3
USA Type Supplementary Services
This section describes how to use supplementary phone services with the
USA Type
Call
Service Mode
. Commands for supplementary services are listed in the table below.
After pressing the flash key, if you do not issue the sub-command before the default sub-
command timeout (2 seconds) expires or issue an invalid sub-command, the current operation
will be aborted.
11.15.3.1
USA Call Hold
Call hold allows you to put a call (
A
) on hold by pressing the flash key.
If you have another call, press the flash key
to switch back and forth between caller
A
and
B
by putting either one on hold.
If you hang up the phone but a caller is still on hold, there will be a remind ring.
Table 61
USA Flash Key Commands
COMMAND
SUB-COMMAND
DESCRIPTION
Flash
Put a current call on hold to place a second call. After the second
call is successful, press the flash key again to have a three-way
conference call.
Put a current call on hold to answer an incoming call.
Flash
*98#
Transfer the call to another phone.

Rate

3.5 / 5 based on 2 votes.

Popular Zyxel Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top