Page 36 / 320 Scroll up to view Page 31 - 35
Chapter 3 Internet / Wireless Setup Wizard
AMG1302/AMG1202-TSeries User’s Guide
36
Note: The wireless stations and AMG1302/AMG1202-TSeries must use the same SSID and
channel ID for wireless communication.
7
The configuration settings are saved and applied. Click
Close
to complete the Internet /
Wireless setup.
Figure 14
Results Summary
8
Launch your web browser and navigate to www.zyxel.com. Internet access is just the
beginning. Refer to the rest of this guide for more detailed information on the complete
range of AMG1302/AMG1202-TSeries features. If you cannot access the Internet, open
the web configurator again to confirm that the Internet settings you configured in the
wizard setup are correct.
Page 37 / 320
AMG1302/AMG1202-TSeries User’s Guide
37
C
HAPTER
4
Tutorials
4.1
Overview
This chapter shows you how to use the AMG1302/AMG1202-TSeries’s various features.
Setting Up Your DSL Connection
, see
page 37
IPv6 Address Configuration
, see
page 39
Setting Up a Secure Wireless Network
, see
page 40
Configuring the MAC Address Filter for Restricting Wireless Internet Access
, see
page 47
Setting Up NAT Forwarding for a Game Server
, see
page 48
Setting Up NAT Forwarding for a Game Server
, see
page 48
Configuring Firewall Rules to Allow a Specified Service
, see
page 50
Configuring Static Route for Routing to Another Network
, see
page 53
Port Binding Configuration
, see
page 55
Configuring QoS to Prioritize Traffic
, see
page 59
Access the AMG1302/AMG1202-TSeries from the Internet Using DDNS
, see
page 62
4.2
Setting Up Your DSL Connection
This tutorial shows you how to set up your Internet connection using the web configurator.
If you connect to the Internet through a DSL connection, use the information from your Internet
Service Provider (ISP) to configure the AMG1302/AMG1202-TSeries. Do the following steps:
1
Connect the AMG1302/AMG1202-TSeries properly. Refer to the Quick Start Guide for details on the
AMG1302/AMG1202-TSeries’s hardware connection.
2
Connect one end of a DSL cable to the DSL port of your AMG1302/AMG1202-TSeries. The other end
should be connected to the DSL port in your house or a DSL router/modem provided by your ISP.
3
Connect one end of Ethernet cable to an Ethernet port on the AMG1302/AMG1202-TSeries and the
other end to a computer that you will use to access the web configuration.
4
Connect the AMG1302/AMG1202-TSeries to a power source, turn it on and wait for the
POWER
LED to become a steady green.
Page 38 / 320
Chapter 4 Tutorials
AMG1302/AMG1202-TSeries User’s Guide
38
Account Configuration
For this example, the interface type is ADSL and the connection has the following information.
General
Mode
Router
Encapsulation
PPPoE
User Name
Password
ABCDEF!
Service Name
My DSL
Multiplex
LLC
IPv6/IPv4 Dual
Stack
Enabled
PPP
Authentication
Auto
VPI
0
VCI
33
Others
IP Address: Obtain IP Address Automatically
DNS Server: Obtained From ISP
IPv6 Address: Obtain IPv6 Address Automatically
DHCP IPv6: DHCP
DHCP PD: Enable
WAN Identifier Type: EUI64
Page 39 / 320
Chapter 4 Tutorials
AMG1302/AMG1202-TSeries User’s Guide
39
Go to
Network Setting > Broadband
, enter or select these values and click
Apply
.
This completes your DSL WAN connection setting.
4.3
IPv6 Address Configuration
If the ISP’s network supports IPv6, the ISP may assign an IPv6 address to the AMG1302/AMG1202-
TSeries automatically.
Page 40 / 320
Chapter 4 Tutorials
AMG1302/AMG1202-TSeries User’s Guide
40
In the
Network Setting > Broadband
screen’s
IPv6 Address
configuration section, select
Obtain an IP Address Automatically
. In the
DHCP IPv6
field select
DHCP
to obtain an IPv6
address from a DHCPv6 server. In the
DHCP PD
field select
Enable
to have the AMG1302/
AMG1202-TSeries pass the WAN prefix to LAN hosts. The LAN hosts can then use the prefix to
generate their IPv6 addresses.
4.4
Setting Up a Secure Wireless Network
Thomas wants to set up a wireless network so that he can use his notebook to access the Internet.
In this wireless network, the AMG1302/AMG1202-TSeries serves as an access point (AP), and the
notebook is the wireless client. The wireless client can access the Internet through the AP.
Thomas has to configure the wireless network settings on the AMG1302/AMG1202-TSeries. Then he
can set up a wireless network using WPS (
Section 4.4.2 on page 41
) or manual configuration
(
Section 4.4.3 on page 45
).
4.4.1
Configuring the Wireless Network Settings
This example uses the following parameters to set up a wireless network. In the client, choose the
AP with the SSID configured here. When prompted for a key, use the Pre-Shared Key configured
here.
IPv6
IPv6
IPv6
SSID
SecureWirelessNetwork
Security Mode
WPA2-PSK
Pre-Shared Key
DoNotStealMyWirelessNetwork
802.11 Mode
802.11b+g+n

Rate

3.7 / 5 based on 3 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top